All Sailing Parts

All Sailing Parts

2266 products

Everything Nacra, Prindle, Hobie and a few more fun odds and ends.

2266 products

Sort

Wave/Getaway Shroud Anchor Plate

Murrays Part# 50-39100011

Hobie® factory replacement shroud anchor chain plate for Club Wave or Getaway. The Club Wave has a three-piece trampoline and shrouds and bridles connect with clevis pins. Current boats use two plates per side.

Hobie Part# 39100011

WAVE/GETAWAY SHROUD ANCHOR PLATE

H-18/20 JIB HALYARD WITH CLIP

The Aussie forestay replaced the original upper and lower forestay system in 2009 on the Hobie 16 as the factory standard. It is modeled after what the dominant Aussie racers using on their boats. Aussie forestays are longer than the classic halyard forestays actually have a separate connection cable for the jib halyard. The separate attachment point for the jib halyard provides a back up if either were to fail. If either the forestay or jib halyard were to break, the other will hold the m

H-16 AUSSIE FORESTAY

Clevis Pin 1/4X3/8

Murrays Part# 50-8020371

This is commonly used for Hobie Rigging parts. It has a 3/8" grip length. You can also use the 1/2" grip length pins also.

Hobie Part# 8020371 or 8020370

CLEVIS PIN 1/4 x 3/8"

MAST HINGE PIN NACRA/H17/20
Murrays Part# 56-F158
The mast base engages the mast ball and is secured by this headless clevis pin to allow the mast to be safely raised or lowered.
Specs: 1/4" diameter x 2-3/8" overall length with a grip length of 1-15/16"
Compatibility: Nacra Inter, F18, N15, F17, 4.5/450, 5.0, 5.2, 5.5SL, 5.7, 5.8NA, 6.0NA, 5.5UNI and 18SQ, as well as Hobie 17, Tiger and 20. Split rings are sold separately.
Compare to Hobie Cat part number 50406301.

NACRA MAST HINGE PIN

Rudder Cam Screws H17, H18, H20,
Older Wave and Getaway
Murrays Part# 001-3551
The Murrays Rudder Cam Pins are a pair of sister screws for use on the Hobie 17, 18, 20, 21, as well as the older Hobie Wave and Getaway rudder cams. These pins are an upgrade form the original stock hollow flare rivet that came on the Hobie. The Sister Screws are much easier to install and remove, and they are reusable.
Compare to Hobie Cat® #5203 and #50312301.
Sold in pairs

H-17/18/20/OLDER WAVE AND GETAWAY RUDDER CAM PINS

CINCH RINGS - Stainless Steel SOLD EACH

13/64" DINGHY CONTROL LINE 5mm

Hobie Getaway Forward Trampoline - 2002-2017 - black mesh Compare to Hobie part number 37980055

Hobie Getaway Forward Trampoline

GETAWAY FORWARD TRAMPOLINE 2002-2016 & 2021-CURRENT

Ronstan Halyard Shackle, 1/4" Pin

Murrays Part# 21-1033

The Ronstan Halyard Shackle with Twist Pin's main advantage is that you cant loose any of it once its attached. The top pin holds it on and the bottom pin dose not come out. Never loose your shackle pins again!

The 1/4" Halyard Shackle with Twist Pin is used in the following Murrays Products: 02-4383-50 N-5.5SL Jib Halyard w/Shackle

RONSTAN HALYARD SHACKLE, 3/16" PIN

Use this 1/8″ Dacron line for batten tie line and roller furling systems. For batten ties, allow about 18″ of line for each batten. Sold per foot. Spool: 1000′ (304.9m). Compare to Hobie part number RH112WHT - 8004510

1/8" DACRON SOLID BRAID

Split Ring

Stainless steel split ring for 5/16″-3/8″ diameter clevis pins. The larger size makes it easier to get on and off.

Large Split ring

Dimensions: 3/4″ Diameter

Material: 316 Stainless steel.

Also called Ring Ding or Ringy Dingy.

Hobie Part number 20860010 – RF686

3/4" SPLIT RING

Hobie Tiller Extension Hinge

Murrays Part# 50-10532010

Hobie® factory replacement tiller extension hinge for #50-20550001 Hobie® Fiberglass tiller extension. Also used on Nacra tillers.

Hobie Part Number: 10532010

Hobie Tiller Extension Hinge

Hobie Part number 10532010

Hobie factory replacement tiller extension hinge for #50-20550001 Hobie Fiberglass tiller extension. Also used on Nacra tillers.

Hobie Part# 10532010

HOBIE TILLER EXTENSION HINGE

Wave Bridle 1/8" Black
Murrays Part# 002-0814-02
One black bridle for Hobie® Wave is constructed to factory specifications. Compare to Hobie Cat® 39822011.

WAVE BRIDLE 1/8" BLACK WIRE

JIB CLEW BLOCK KIT

CAT TRAX CRADLES (PAIR)

Quick Release Deluxe Pin 1/4 X 1.5 with Lanyard

Murrays Part# 18-4M150L

This quick release pin features a push button on the top that releases 2 spring-loaded balls at the tip that secure the pin in place.

This pin includes a lanyard to help prevent loss of pin. Uses: Hobie 18 mast hinge pin,

Compare to Hobie part#P 20307 PIN, QR 1/4 X 1-1/2 CUP

Upgrade for Hobie 8020181, 8020180, 8020431, 8020430, 8020420, 8020421

QUICK RELEASE DELUXE PIN 1/4 X 1-1/2" WITH LANYARD

EZ Lock Upper Pintle

Murrays Part# 50-90880211

Hobie® factory replacement upper pintle for EZ Loc rudder system.

Fits Hobie Bravo and Getaway boats

Hobie Part# 90880211

BRAVO/WAVE/GETAWAY EZ LOC UPPER PINTLE

H14/16 Aluminum Rudder Pins

Murrays Part# 001-2272

Aluminum rudder pins are standard on Hobie® 14 and 16 and are good for all-around, low maintenance use. Pair of 3/8" x 8" rudder pins with cotter pins.

New One piece rudder gudgeons have been produced with a slightly smaller metric hole size. If you have a 2020 and newer boat or 2020 and newer one piece gudgeons, our aluminum rudder pins may require force to install and be difficult to remove. The stainless pins are a better fit.

Sold in pairs

Aluminum rudder pins are standard on Hobie® 14 and 16 and are good for all-around, low maintenance use. Pair of 3/8" x 8" rudder pins with cotter pins.

New One piece rudder gudgeons have been produced with a slightly smaller metric hole size. If you have a 2020 and newer boat or 2020 and newer one piece gudgeons, our aluminum rudder pins may require force to install and be difficult to remove. The stainless pins are a better fit.
Sold in pairs
Each pair is equivalent to two Hobie Cat® item# 20880001 (each)

H-14/16 ALUMINUM RUDDER PINS

DYNEEMA SK78 12-STRND 3mm GRAY

ROBLINE OCEAN 3000 DYNEEMA SK78

Harken Gloves 3/4 Finger Classic
Sailing Glove

The perfect all-purpose glove. Double-thick Black Magic® material for superior grip. Minimal stretch when wet, dries soft. Durable nylon spandex mesh. Full-finger or 3/4 finger. Tab lock for secure closure. Junior size available.

Use this page to order Sticky Race Short Gloves product numbers:

28-2385 XS
28-2386 S
28-2387 M
28-2388 L
28-2389 XL
28-2390 XXL

HARKEN GLOVES 3/4 FINGER CLASIC SAILING GLOVE

PRINDLE MAST STEP HINGE PIN

The Murrays Trapeze handle features a contoured grip and a wire guide prevent hand contact with the wire. A recessed cavity in the base holds the nicropress oval and shields the sailor from sharp wire ends.

Sold Individually.

Hobie uses item #2011 for this handle.

Used on Nacra, Prindle and Hobie catamarans.

Nacra 5.7 Double Trapeze (4 handles)

The Murrays Double Trapeze is a set of 4 black or white coated trap wires with 4 handles for double trapezing. A single thimble per pair of handles eliminates clutter at that mast connection.
Order shock cord, harness loops and adjustment kits separately.

A complete trapeze system requires the following:
Harness loop - Can't Miss Ring or Dogbone
Trap Shock Cord
Trap Adjustment kit
Sailing Harness

Trapeze adjustment kits (#001-1121, 001-1130 or 001-1140, purchased se

MURRAYS TRAPEZE HANDLE

Hobie Tracker Deck Plate

Murrays Part# 007-1051

The standard replacement deck plate for the traveler on all Hobie® 14, 16 and newer 17's

Uses a 3/16 x 1/2" clevis pin to attach to the main sheet system.

Also used in Hobie 14 and Hobie 16 upgrade downhaul systems to secure lower block.

Sold individually

Hobie part# 11870000

Hobie Tracker Deck Plate

Murrays Part# 007-1051

The standard replacement deck plate for the traveler on all Hobie® 14, 16 and newer 17's

Uses a 3/16 x 1/2" clevis pin to attach to the main sheet system.

Also used in Hobie 14 and Hobie 16 upgrade downhaul systems to secure lower block.

Sold individually

Hobie part# 11870000

TRACKER DECK PLATE (EA)

Sail Pocket Protector Kit Jib

Murrays Part# 001-1002

The Jib Sail Pocket Protector Kit includes one pair of tough nylon protectors with indentations for included rivets that are set with a hammer.

JIB SAIL POCKET PROTECTOR KIT

MAGIC MARINE SMART HARNESS CE

Replace a 3/16" bow shackle with this quick-release version to add convenience. Can be used on 2-1/4" blocks. Compare to Hobie Cat® #3062.

QUICK RELEASE 3/16" BOW SHACKLE

Quick Release Pin Deluxe  3/16 X 3/4"

Murrays Part# 18-3M075

This Quick Release Pin features 2 locking balls for a extra secure grip, and a push button deluxe dished head with a hole for lanyard attachment. The Deluxe pin is quick and easy to remove and install, and makes getting on and off the water quicker and easier.

QUICK RELEASE PIN DELUXE 3/16 X 3/4"

Harken 22mm Block

Murrays Part# 28-0224

This Harken ball bearing micro single block with stainless side plates is a small block with high load capabilities. It is a premium quality block for your trapeze return system.

HARKEN 22MM BLOCK

18SQ Forestay 5/32 Black
Murrays Part# 002-5045-02
Black coated forestay for your NACRA 18 Square built to original specifications.

H-14 FORESTAY 1/8" WIRE

Comp-Tip Cover: H-16/18/20
Murrays Part# 31-2441
Hobie Cat recommends that CompTips on Hobie 16, 17, 18 and 20 be covered to protect them from ultraviolet light. Top quality polyester material is treated for UV-resistance and provides much better and long-lasting protection than nylon covers. Highly visible, red-tip reinforced end. Cover ties to mast with included line.

H-16/18/20 COMP-TIP COVER

Tren Tec Hobie 16 main sail luff batten caps prevent batten splitting and align batten to the angle of the sail. Glue cap to the forward end of the batten.

Increases the life of the sail

Prevents battens ripping the sail pockets

Prevents battens from splitting

Aligns battens to the angle of the sail

Sold in packages of 8

Hobie Part# 1562

Tren Tec Hobie 16 main sail luff batten caps prevent batten splitting and align batten to the angle of the sail. Glue cap to the forward end of the batten.

Increases the life of the sail

Prevents battens ripping the sail pockets

Prevents battens from splitting

Aligns battens to the angle of the sail

Sold in packages of 8

Hobie Part# 1562

H-16 ANGLED LUFF CAPS (8)

Rivet CCC 6-6 (3/16 X 3/8) Countersunk
Murrays Part# 19-5024
Countersunk stainless steel 3/16" x 3/8" rivet for traveler tracks, etc.
Compare to Hobie Part # 8010201.
This rivets is what Hobie recommends for both the main traveler tack and the jib traveler track.
We also recommend using an 1/8" stop sleeve, part number 002-1041, as a spacer to help you apply pressure on the rivet inside the track, as the track is too narrow for most rivet guns to get far enough inside to apply pressure to the rivet.

RIVET CCC 6-6 CSK

Quick-Release Pin Detent 1/4 X 1-1/2
Murrays Part# 18-4D150
The Quick-Release Pin Detent 1/4 X 1-1/2 is an economical, quick connection for Hobie 16 mast step pin. A spring-loaded ball exerts sufficient pressure to help avoid accidental release. Measurements are 1/4″ diameter x 1-1/2″ maximum grip length (distance from the shoulder to the locking ball bearings).

QUICK RELEASE DETENT PIN 1/4 X 1-1/2"

Murrays Original Hobie 14 & 16 Jib traveler car for pre 1994 boats with the external track on the front crossbar. 21230000

Murrays Hobie 16 Jib Traveler car. Jib Sheet. Hobie 16 front crossbar. Jib track, corner casting, blue trampoline

MURRAYS H-16 JIB TRAVELER CAR

Hull Cradle: Universal

Murrays Part# 13-7010

HULL CRADLE: UNIVERSAL

Prindle split rings and clevis pin kit, mast hinge pin

PRINDLE PINS & RINGS KIT

Screw Delrin 3/8-16 X .75"

Murrays Part# 50-8032001

Hobie® factory replacement 3/8-16 x 3/4" Delrin screw is used as rudder rake adjustment screw on Pre-EZ Lock Rudder System.

Hobie Part# 8032001

HOBIE RUDDER RAKE ADJUSTMENT SCREW - 8032001

Wave Mainsheet S Hook

Murrays Part# 50-38900031

Hobie® factory replacement S-hook for Wave mainsheet. Mainsheet is 35 feet of Dacron® spun braid #39-055. Makes it easy to attach mainsheet to sail and standard on all new boats.

Hobie Part# 38900031

WAVE MAINSTEET S HOOK

Rudder Casting Lock Spring
Murray Part# 50-10430000
Hobie factory replacement 2-1/8" lock spring for rudder casting. Replace rudder springs with this original spring supplied on Hobie® 14, 16, (pre 1983) 17 and 18.
Compare to HC part number 10430000
H14, H16, H17, H18, H20

HOBIE RUDDER SPRING

Previous 1 … 3 4 5 6 7 … 57 Next

Recently viewed

All Sailing Parts