Hobie

Hobie

610 products

    All Hobie OEM parts.  Sails to rudders, trampolines to batten caps.

    610 products
    Hobie Shroud Adjuster Covers 11″ Pair are vinyl covers that protect the crew from metal shroud adjusters and can prevent de-masting by protecting the split rings. Includes two adjuster covers, one for each side of the boat. Available in white and black. Compatible with al beach cats: Nacra, Prindle, A-Cat, Dart, Sol Cat, G-Cat...
    11" SHROUD ADJUSTER COVERS
    Hobie
    Out of Stock
    Hobie Rudder Cam Hobie part number 10480000 Hobie factory replacement cam. Rudder cams should be inspected and replaced periodically. Always replace cams that are bent out of shape. Used on all Hobie Catamarans with metal housing rudder systems. Compatible on all Hobie 14, 16, 17, 18, 20, 21SC and 21SE as well as older Wave and Getaway models. Not compatible with the Hobie Wave and Getaway EZ Loc plastic rudder housing rudder system.
    HOBIE RUDDER CAM
    Hobie
    RUDDER LOCKING KIT Hobie 16 Murrays Part# 50-10311900 Hobie factory rudder locking kit for Hobie 14 or 16 includes one each plunger, 2-1/2" spring (#50-10432000), and Delrin screw. Delrin screw is 3/4-10 thread. In many cases you can drill it out with a 5/8" drill bit and then get a 3/4-10 tap to clear the threads.
    H-14/16 RUDDER LOCKING KIT
    Hobie
    Hobie rivet casings sleeves seal rivets to prevent water penetration. When used with a rivet they seal the hole to prevent water from getting through the center of the rivet. Rivet Casings are recommended for use on all rivets on the mast to keep the mast water tight. Compatible with all 3/16 diameter rivets up to 5/8" long. Compatible with all rivets on Hobie, Nacra and Prindle catamarans except traveler tracks. Requires 13/64" hole. Hobie part number 8011291, 8011290, also called rivet cap.
    RIVET CASING 6-10(3/16 X 5/8)
    Hobie
    RUDDER CASTING DELRIN SCREW - rudder locking adjustment screw - 60450000
    HOBIE DELRIN RUDDER SCREW - 60450000
    Hobie
    MAST STEP LINK KIT H14/16 Hobie part number 21380001
    H-14/16 MAST STEP LINK KIT
    Hobie
    Hobie Halyard - Downhaul Cheek Block - 20710000 Murrays Part# 25-3340 The plastic sheave degrades and breaks on older Hobie® 16 downhaul cheek blocks and the entire block must be replaced. Also fits Sol Cat 18. Hole spacing 1/2" on center from side to side; 2-3/4" on center from end to end. To install, use four #19-5031 6-4 rivets and four #19-5020 sealing casings. Hobie Cat® Part# 20710000.
    HOBIE CHEEK BLOCK - 20710000
    Hobie
    Mast Step Pin Wave/Getaway .25 x 2" Detent Murrays Part# 50-8020451 Replacement mast step pin / mast hinge pin for a Hobie Wave and Getaway. 1/4" x 2" detent pin.   Hobie part # 8020451
    MAST STEP DETENT PIN .25x2"
    Hobie
    H16 and Sol Cat Jib Hank Hobie part number 22090001 Hobie factory jib hank attaches the jib to the forestay of a Hobie 16 or Sol Cat
    H-16/SOL CAT JIB HANK
    Hobie
    Out of Stock
    Hobie factory replacement retainer clip for Hobie 20-style tiller connector and adjuster kit (#07-1953). TILLER CONNECTION RETAINER CLIP - HOBIE 20. 40590000 MURRAYS.COM - IN STOCK
    Hobie 1953 tiller connection kit - new style
    H-20 TILLER CONNECTOR RETAINER CLIP
    Hobie
    Mast Ball H20/21/Getaway Hobie part number 30110001 Hobie factory replacement mast ball for Hobie 20, Hobie 21 and Hobie Getaway. Ball measures 1-1/2" diameter with a 5/8" hole.
    H-20/21/GETAWAY MAST BALL
    Hobie
    The Hobie Baby Bob Mast Float is designed to offer the safety and security of mast head flotation with minimized drag through the air, the Baby Bob is fixed in position to the mast head with the included mounting hardware. The Baby Bob is standard on all Hobie Waves This float will also fit the Getaway and Hobie 16 with or without CompTip. Some drilling may be necessary. The larger Mama Bob (#07-30119) is also an option for most Hobies. The Baby Bob Mast Float displaces 32 pounds of water, is 20" long x 1
    MAST FLOAT WAVE BABY BOB
    Hobie
    H14/16 Bow Tang Murrays Part# 50-20120000 Hobie® factory replacement bow tang for Hobie® 14, 16 or Getaway. Use #19-3530 screw and #19-2520 nylock nut on Hobie 16; use #19-3530 screw on Hobie 14. The original Hobie® 14 tang is no longer available. 20120010
    Hobie factory replacement bow tang for Hobie 14, 16 or Getaway. Use #19-3530 screw and #19-2520 Nylock nut on Hobie 16; use #19-3530 screw on Hobie 14. The original H14 tang is no longer available. Hobie Part# 20120000 and 20120010
    H-14/16 BOW TANG
    Hobie
    Hobie 1953 tiller connection kit - new style
    HOBIE TILLER CONNECTOR KIT
    Hobie
    RIVET MCP 6-8 3/16x1/2" PH Murrays Part# 50-8011231 Hobie® factory 6-8 heavy duty rivet requires a rivet tool for installation. 3/16" x 1/2" pan head. Fits Hobie Getaway Eyelet Post. Fits Hobie 20 Eyelet Post. Mounts Wave Mast Step Hobie part number 8011231
    RIVET MCP 6-8 3/16x1/2" PH
    Hobie
    Batten Cap Hobie Main Leech Murrays Part# 50-11323000 Hobie® factory replacement part number 11323000. Hobie batten cap are sold individually. Order batten tie separately; 18" of 1/8" line per batten cap is standard. Sold individually
    HOBIE MAIN LEECH BATTEN CAP
    Hobie
    Hobie EZ Lock Rudder retainer clip Murrays Part# 50-90880231 Retainer clip for Hobie Bravo EZ Loc Rudder Housing. Hobie Part# 90880231
    HOBIE EZ LOCK RUDDER CLIP
    Hobie
    Hobie 18 rudder plunger. Hobie Part number 50312201. Also use on the 17 as well as the older Wave and Getaway
    H-17/18/GETAWAY RUDDER CAST PLUNGER
    Hobie
    Sale
    HOBIE FULL AUTO HARNESS - SMALL
    Hobie
    Save $96
    Clevis Pin 1/4X3/8 Murrays Part# 50-8020371 This is commonly used for Hobie Rigging parts. It has a 3/8" grip length. You can also use the 1/2" grip length pins also. Hobie Part# 8020371 or 8020370
    CLEVIS PIN 1/4 x 3/8"
    Hobie
    Hobie Shroud Anchor Bar Murrays Part# 50-50101701 This is the bar that the shroud anchor pins screws into to secure the shrouds on. Shroud anchor bar for Hobie Cat masts (replaces the nut used on older models). Use with the anchor pin to secure under the lip of the hull. Stainless steel Length: 3.5 inches Application: Hobie 14/16/17/18 sailboats Compare to Hobie Part# 50101701
    HOBIE SHROUD ANCHOR BAR
    Hobie
    Rudder Casting Plunger H14/16 Murrays Part# 50-10440000 Hobie® factory replacement rudder casting plunger for Hobie® 14 or 16.
    H-14/16 RUDDER CASTING PLUNGER
    Hobie
    Out of Stock
    Hobie 16 One Piece Gudgeon Upper and Lower Bushing Insert - 50102010
    H-16 ONE PIECE GUDGEON UPPER AND LOWER BUSHING INSERT
    Hobie
    Out of Stock
    Hobie 16 Mast head sheave - Old Style Murrays Part# 51-16041711 The Hobie 16 Mast head sheave - Old Style is the large plastic pulley sheave that replaces the sheave in the original all aluminum Hobie 16 mast. Requires a 3/8" x 1.5" clevis pin or bolt to install Hobie 16 pre comptip masthead sheave. Measures 4 7/8" x 3/8" with a 3/8" hole.
    H-16 MAST HEAD SHEAVE-OLD SYLE
    Hobie
    Rudder Casting Lock Spring Murray Part# 50-10430000 Hobie factory replacement 2-1/8" lock spring for rudder casting. Replace rudder springs with this original spring supplied on Hobie® 14, 16, (pre 1983) 17 and 18. Compare to HC part number 10430000 H14, H16, H17, H18, H20
    HOBIE RUDDER SPRING
    Hobie
    Hobie Tiller Extension Hinge Murrays Part# 50-10532010 Hobie® factory replacement tiller extension hinge for #50-20550001 Hobie® Fiberglass tiller extension. Also used on Nacra tillers. Hobie Part Number: 10532010
    Hobie Tiller Extension Hinge Hobie Part number 10532010 Hobie factory replacement tiller extension hinge for #50-20550001 Hobie Fiberglass tiller extension. Also used on Nacra tillers. Hobie Part# 10532010
    HOBIE TILLER EXTENSION HINGE
    Hobie
    Hobie Tracker Deck Plate Murrays Part# 007-1051 The standard replacement deck plate for the traveler on all Hobie® 14, 16 and newer 17's Uses a 3/16 x 1/2" clevis pin to attach to the main sheet system. Also used in Hobie 14 and Hobie 16 upgrade downhaul systems to secure lower block. Sold individually Hobie part# 11870000
    Hobie Tracker Deck Plate Murrays Part# 007-1051 The standard replacement deck plate for the traveler on all Hobie® 14, 16 and newer 17's Uses a 3/16 x 1/2" clevis pin to attach to the main sheet system. Also used in Hobie 14 and Hobie 16 upgrade downhaul systems to secure lower block. Sold individually Hobie part# 11870000
    TRACKER DECK PLATE (EA)
    Hobie
    H18 Mast Head/Base Sheave Murrays Part# 50-60620000 Factory replacement sheave for Hobie 18 mast head/base and outhaul assembly. Specs: 1" Diameter x 3/8" wide and 1/4" hole. Also used as traveler control line turning sheave on 2005 and newer Hobie 16 sailboats. Applications: Hobie 18 - Mast head halyard sheave ; mast base halyard sheave ; outhaul car sheaves. Hobie 16 - Jib Traveler line sheave. (in the H16 Race Corner Castings) use 50-8011251 Rivet
    H-18 MAST HEAD/BASE SHEAVE
    Hobie
    Screw Delrin 3/8-16 X .75" Murrays Part# 50-8032001 Hobie® factory replacement 3/8-16 x 3/4" Delrin screw is used as rudder rake adjustment screw on Pre-EZ Lock Rudder System. Hobie Part# 8032001
    HOBIE RUDDER RAKE ADJUSTMENT SCREW - 8032001
    Hobie
    Wave/Getaway Shroud Anchor Plate Murrays Part# 50-39100011 Hobie® factory replacement shroud anchor chain plate for Club Wave or Getaway. The Club Wave has a three-piece trampoline and shrouds and bridles connect with clevis pins. Current boats use two plates per side. Hobie Part# 39100011
    WAVE/GETAWAY SHROUD ANCHOR PLATE
    Hobie
    H18 Traveler Cylinder Bearing Set Murrays Part# 50-61852000 Hobie® factory replacement cylinder bearing set for Hobie® 18 main traveler. Set includes one pair.
    Hobie 18 main traveler car parts list - 6180001, 8040301, 61870000, 61880000, 60190000, 8050311, 61842000, 8060121, 61810000, 61830000, 61852000, 8020431
    H-18 TRAVELER CYLINDER BEARING SET
    Hobie
    H14/16/18 Gooseneck Boom Pin Murrays Part# 50-10772010 Hobie® factory gooseneck boom pin for Hobie® 14, 16 or 18.
    H-14/16/18 GOOSENECK BOOM PIN
    Hobie
    HOBIE 14/16 GOOSENECK ASSEMBLY Murrays PN 50-10770001 Hobie factory replacement gooseneck assembly for Hobie 14 or 16. Hobie Cat item #10770001.
    H-14/16 GOOSENECK ASSEMBLY
    Hobie
    EZ Lock Upper Pintle Murrays Part# 50-90880211 Hobie® factory replacement upper pintle for EZ Loc rudder system. Fits Hobie Bravo and Getaway boats Hobie Part# 90880211
    BRAVO/WAVE/GETAWAY EZ LOC UPPER PINTLE
    Hobie
    Out of Stock
    The tune-up kit for Hobie® roller furling drum 61900000 includes all of the items that commonly wear or break (bearings, bearing cage, nyliner, nylon sleeve, darby rings, spool and housing). Murrays.com
    HOBIE ROLLER FURLER TUNE-UP KIT
    Hobie
    NUT SQUARE 10-32 Murrays Part# 50-8051301 Hobie® factory replacement stainless steel 10-32 square nut can be used when mounting downhaul/halyard cleat on Hobie® 14 or 16. Also can be used for mounting H17 trampoline eye straps. Use 19-2910 screw. Hobie Part# 8051301
    NUT SQUARE 10-32
    Hobie
    Batten Cap Jib Leech H16 Murrays Part# 50-2133000 Hobie® factory jib leech batten cap for Hobie® 16. For batten tie, use 18" of 1/8" Dacron® solid braid #39-0221. These are also used on the top two battens of a Hobie Wave and the top batten of a Hobie 18 Mainsail. Sold individually
    HOBIE JIB BATTEN LEECH CAP (EA)
    Hobie
    Wave Mainsheet S Hook Murrays Part# 50-38900031 Hobie® factory replacement S-hook for Wave mainsheet. Mainsheet is 35 feet of Dacron® spun braid #39-055. Makes it easy to attach mainsheet to sail and standard on all new boats. Hobie Part# 38900031
    WAVE MAINSTEET S HOOK
    Hobie
    Hobie 20-style factory tiller connector post. Part of the Hobie 1953 tiller connection system. Hobie part number 40530000 and 40530001
    Hobie 1953 tiller connection kit - new style
    H-20 TILLER CONNECTOR POST
    Hobie
    Out of Stock
    HOBIE 16 MAINSAIL BATTEN CAP KIT - LEACH - 1522H
    H-16 MAINSAIL BATTEN LEACH CAP KIT (8)
    Hobie
    Recently viewed