Harken

Harken

184 products
    184 products
    Harken 22mm Block Murrays Part# 28-0224 This Harken ball bearing micro single block with stainless side plates is a small block with high load capabilities. It is a premium quality block for your trapeze return system.
    HARKEN 22MM BLOCK
    Harken
    Harken Calibration Strip Murrays Part# 28-2306 This handy, self-stick scale takes the guesswork out of setting the downhaul. The scale is marked in 1/2" increments to 10". The sticker can also be used as an outhaul scale, or jib track measurement guide. Features both vertical and horizontal numbers so it can be used on the mast or the crossbar.
    HARKEN CALIBRATION STRIP
    Harken
    HARKEN 6MM BOW SHACKLE
    Harken
    Harken 396 - 29mm Harken 180 Pivoting Block with Carbo-Cam, downhaul, Hobie.
    HARKEN 29MM PIVOTING LEAD BLOCK-CARBO-CAM CLEAT
    Harken
    Harken Shackle Stamped 3/16" Murrays Part# 28-0072 Harken's stainless stamped D-shackle has 3/16" diameter pin. For Harken 2.25" blocks
    HARKEN SHACKLE STAMPED 3/16"
    Harken
    Murrays 57mm Carbo 6:1 Mainsheet System Murrays Part# 28-61 The Murrays Harken 57mm Carbo 6:1 Mainsheet System is an improved low profile mainsheet system for Hobie 16.  By attaching a fairlead to the back side of the cleat mount the Murrays system does not need a becket on the lower block which makes the system more compact and gives sailors the ability to sheet in farther and or rake the mast back farther before having the mainsheet bottom out and go block to block.
    HARKEN 57MM CARBO 6:1 MAINSHEET SYSTEM
    Harken
    Harken Sail Chafe Protector Murrays Part# 28-0285 Harken's Sail Chafe Protector Set replaces the diamond wire rollers to protect the jib from chafing on the diamond wire spreader. The split rollers are pre-drilled to fit up to 3/16" wire. Each 2-3/4"-diameter (70mm) protector has two pieces that snap together for easy installation. Used on Hobie 18, Hobie 20, Prindle 18.2, Prindle 19, Nacra 15, 17, 18, Inter 20, F18
    HARKEN SAIL CHAFE PROTECTOR (2)
    Harken
    Harken 1/4" Torlon Ball Bearing-21 Balls Murrays Part# 28-0177 1/4" Torlon replacement ball bearings fit Harken 158, 159, 172, 210, 212, 214, 215, 249, 440 and 441. A bearing loader, #28-HSB8 (sold separately), is required for installation. Sold in packages of 21
    HARKEN 1/4" TORLON BALL BEARING (21)
    Harken
    Harken 29mm Bullet Sheave Murrays Part# 28-0160 Harken's downhaul/halyard sheave makes raising the sail and/or adjusting the downhaul with Harken ball bearing sheaves much easier. This is a direct replacement for the sheaves that came with early Hobie 17s.
    HARKEN 29MM BULLET SHEAVE
    Harken
    Harken 57mm Ratchet Block - Swivel, Becket, Cam Cleat Murrays Part# 28-2139 Harken 57mm jib block is great for use on almost all Hobie Cat, Nacra and Prindle. Carbo Ratchets allow sailors to hand-hold loaded lines and offer balance between holding power and controlled easing. Specifications Sheave diameter: 2-1/4" Length: 4-15/16" Weight: 9 oz Shackle pin diameter: 3/16" Maximum line diameter: 3/8" Maximum working load: 600 lb. Breaking load: 1500 lb.
    HARKEN 57MM RATCHET BLOCK- SWIVEL, BECKET, CAM CLEAT
    Harken
    Harken 29mm Clew Block Murrays Part# 28-0371 Harken's 29mm Carbo block assembly is designed to be sewn onto the clew of a sail. It can be used to replace the jib clew block on Hobie® 14 and 16. Specifications: 330 lb. SWL; 1000 lb. breaking strength; 5/16" maximum line diameter.  On Hobie® 14 and 16, attach with #21-1032 twist pin halyard shackle. Harken Part# 371
    HARKEN 29MM CLEW BLOCK
    Harken
    Harken 29mm Bullet Block Murrays Part# 28-0082 Medium-size Harken single bullet block with Delrin® ball bearings works well for control line or jib sheeting lines. The low-friction bullet block is compact and lightweight, with fast trim and release under high or low loads.
    HARKEN 29MM BULLET BLOCK
    Harken
    Harken 6mm Stamped Shackle Murrays Part# 28-0138 Harken's stainless stamped D-shackle has 1/4" diameter pin. For Harken 3.00" blocks. Stamped shackles are used on most Harken Small Boat Blocks and are appropriate for low loads. For higher loads, select forged and high-resistance shackles instead.
    HARKEN 6MM STAMPED SHACKLE
    Harken
    Harken 22mm Cheek Block Murrays Part# 28-0233 Harken micro cheek is used as a downhaul and turning block and as the Hobie 16 jib traveler control line block on the front crossbar. Specifications: 200 lb. SWL 1200 lb. breaking strength 1/4" maximum line diameter 7/8" sheave diameter 2-1/2" long
    HARKEN 22MM CHEEK BLOCK
    Harken
    Harken Swivel with Carbo Cam Bullseye Murrays Part# 25-3010 Swivel cam cleats are ideal for main traveler control and up-release jib cleating systems. Cam cleats and fairleads should be selected on the basis of need. Order plastic base pads and flat head screws separately to mount to your front crossbar.
    HARKEN SWIVEL WITH CARBO CAM & BULLSEYE
    Harken
    Harken 22mm Spring Murrays Part# 28-0071 Harken universal stand-up spring supports blocks on pad eyes, eyestraps, bases and traveler cars. Weight: .32 oz. This works well with snap shackle w/tack to upgrade a typical beachcat mainsheet system.
    HARKEN 22MM SPRING
    Harken
    Out of Stock
    Harken 57mm Carbo 10:1 System Murrays Part# 28-101 This system offers 10:1 purchase power! Light weight, low profile and very strong, these Carbo AirBlocks® have enormous working range, with a higher working load than standard blocks, even though they are lighter in weight. The base block has an on-off ratchet and will roll freely in both directions when disengaged, such as in light air. Engage the ratchet in heavy air when you need the mechanical advantage of the ratchet.
    HARKEN 57mm CARBO 10:1 SYSTEM
    Harken
    Harken H16 Race 6:1 Main Sheet System Murrays Part# 28-61p The 6:1 Race Mainsheet System is a low profile mainsheet system is super light weight and allows for maximum mast rake. The base block is the 57mm Harken Carbo Ratchamatic from our regular 6:1 system with a 40mm carbo triple on the top. The Harken 57mm base block has a load sensing ratcheting system to help hold the line when it is under tension.
    HARKEN H-16 RACE 6:1 MAIN SHEET SYSTEM
    Harken
    Harken Traveler Car Bearing Loader
    HARKEN TRAVELER CAR BEARING LOADER
    Harken
    Harken Standard Cam-Matic Cleat -150 Murrays Part# 28-0150 For high load/high-wear applications. Cam-Matic® ball bearing cam cleats engage and release easily, hold securely, and work with a wide range of line types and sizes. Cam teeth are smooth to protect line and because tooth grip is not required to close the pawls. Three rows of UV-stabilized, Delrin® ball bearings provide minimal friction for easy line engagement and release, even under high loads.
    HARKEN STANDARD CAM-MATIC CLEAT-150
    Harken
    Harken 4mm Shallow Bow Shackle Murrays Part# 28-2131 Forged stainless steel shackles are polished to a high luster and are stamped with the screw pin diameter. Bow shackles are best for multidirectional loads. Shallow bow shackles are proportionally wider for their length than regular bow shackles.
    HARKEN 4MM SHALLOW BOW SHACKLE
    Harken
    Harken 57mm Carbo Ratchamatic 12:1 Low-Profile Mainsheet System Murrays Part# 28-121 The Harken 57mm Carbo Ratchamatic 12:1 Low-Profile Mainsheet System is a Light weight, low profile and very strong. These Carbo AirBlocks® have enormous working range, with a higher working load than standard blocks, even though they are lighter in weight! The Carbo Ratchmatic® is a load-sensing ratchet block that rolls freely in both directions under low loads, and automatically engages the ratchet as loads increase.
    HARKEN 57mm CARBO 12:1 SYSTEM
    Harken
    Harken 29mm Bullet Block-Becket Murrays Part# 28-0083 Medium-size Harken single bullet block with becket has Delrin® ball bearings and works well for control line or jib sheeting lines. The low-friction bullet block is compact and lightweight, with fast trim and release under high or low loads. Free-rolling Delrin® ball bearings. Sheave and sideplates are UV-stabilized with carbon-black additive for maximum protection.
    HARKEN 29MM BULLET BLOCK-BECKET
    Harken
    HARKEN SWIVEL WITH ALUMINUM CAM & BULLSEYE
    Harken
    Out of Stock
    Harken 40mm Ratchet Block-Swivel, Becket, Cam Cleat Murrays Part# 28-2611 ​Carbo Ratchets allow sailors to hand-hold loaded lines and offer balance between holding power and controlled easing.
    HARKEN 40MM RATCHET BLOCK-SWIVEL, BECKET, CAM CLEAT
    Harken
    Out of Stock
    Harken Standard Flairlead Fiber-reinforced plastic flairlead mounts on Harken aluminum or Carbo Cam cleat to allow the cleat to be used when lines enter or leave the cam at unfair angles. Length (in) 2 3/16 in Length (mm) 56 mm Width (mm) 21 mm Width (in) 1 3/16 in Weight (g) 7 g Weight (oz) 0.25 oz Fastener spacing (mm) 38 mm Fastener spacing (in) 1 1/2 in Height above cam (in) 5/8 in Height above cam (mm) 16 mm Fits cam 365 Harken Part# 425
    +1
    HARKEN STANDARD FLAIRLEAD
    Harken
    Harken Gloves 3/4 Finger Classic Sailing Glove The perfect all-purpose glove. Double-thick Black Magic® material for superior grip. Minimal stretch when wet, dries soft. Durable nylon spandex mesh. Full-finger or 3/4 finger. Tab lock for secure closure. Junior size available. Use this page to order Sticky Race Short Gloves product numbers: 28-2385 XS 28-2386 S 28-2387 M 28-2388 L 28-2389 XL 28-2390 XXL
    HARKEN GLOVES 3/4 FINGER CLASIC SAILING GLOVE
    Harken
    Harken Micro Carbo-Cam Kit-Wire Fairlead Murrays Part# 28-0473 ​Wire fairleads maintain a low profile while holding the line close to the cleat. Kit includes lightweight, fiber-reinforced 471 Carbo Cam, and 475 wire fairlead.
    HARKEN MICRO CARBO-CAM KIT-WIRE FAIRLEAD
    Harken
    Harken Rubber Standup Boot -55mm Murrays Part# 28-0370 Made of durable, flexible PVC, stand-up boots hold blocks up without snagging lines. The 370 fits 75 mm Carbo blocks. Harken Part# 370
    HARKEN 55MM STANDUP BOOT
    Harken
    Harken Traveler Car End Plates Murrays Part# 28-HSB78 End cap kit for #28-0214 Harken traveler car includes 2 end caps, screws, blue loc-tite and instructions. Sold as a pair
    HARKEN TRAVELER CAR END PLATES (2)
    Harken
    Harken 57mm Carbo 8:1 System Murrays Part# 28-81 Lightweight, low profile and very strong, these Carbo AirBlocks® have enormous working range, with a higher working load than standard blocks, even though they are lighter in weight! The Carbo Ratchmatic® is a load-sensing ratchet block that rolls freely in both directions under low loads, and automatically engages the ratchet as loads increase.
    HARKEN 57mm CARBO 8:1 SYSTEM
    Harken
    Harken 57mm Carbo Ratchamatic 7:1 Low-Profile Mainsheet System Murrays Part# 28-71 The Harken 7:1 Mainsheet System includes a 57mm Triple Carbo Ratchamatic Base with 40mm Carbo single (Harken #HSB360) added on to it and a 57mm Triple with becket boom block (Harken #2605) By adding the 40mm Carbo single to the base block we have turned this into a low profile 7:1 Mainsheet system. line is not included. Safe working load is 1500 pounds; breaking strength is 3750 pounds.
    HARKEN 57MM CARBO RATCHAMATIC 7:1 LOW-PROFILE MAINSHEET SYSTEM
    Harken
    Harken 56mm Padeye - 2 Fasteners Murrays Part# 28-2759 This is an upgrade for your harken main traveler car. It is being used on the NACRA 17 Olympic boats to replace the failing eyestrap. It will typically require longer bolts/ screws. This is a heavy duty cast stainless steel padeye. Fits on Harken Car 2738 and 2756 Harken Part# 2759
    HARKEN 56MM PADEYE - 2 FASTENERS
    Harken
    Harken 2156 40mm Pivot 180 Block with Cam
    HARKEN 40MM PIVOTING LEAD BLOCK- CAM-MATIC CLEAT
    Harken
    Harken 29mm T2 Soft-Attach Block Murrays Part# 28-2146 For catamarans, this tie-on block eliminates the need for shackles, posts, swivels, etc. It is ultra-lightweight and sized like a bullet-block. Specifications: 1-1/8" sheave diameter 330 lb. SWL 1000 lb. breaking strength 5/16" maximum line diameter The high-strength composite T2™ is the first block with no metal shackles or rivets.
    HARKEN 29MM T2 SOFT-ATTACH BLOCK
    Harken
    Harken Micro Wire Fairlead Murrays Part# 28-0475 Harken's wire fairlead places the fairlead ahead of the cam and holds line at cleat when not in use. Fits Harken 468 and 471 cams. Wire fairleads maintain a low profile while holding the line close to the cleat.
    HARKEN MICRO WIRE FAIRLEAD
    Harken
    Harken Micro Cam-Matic Cleat Murrays Part# 28-0468 Harken's Cam-Matic cleat has multiple rows of high-load ball bearings to reduce friction so that cams open easily for snap-down, rather than draw-through cleating. The cam horns and smooth V-shape guide line for easy entry. This allows precise sail control without having to readjust the cleated line.
    HARKEN MICRO CAM-MATIC CLEAT
    Harken
    Out of Stock
    Harken 4:1 Mainsheet System
    Murrays Hobie wave main sheet system
    HARKEN 4:1 MAIN SHEET SYSTEM
    Harken
    Harken 16mm Block-Becket Murrays Part# 28-0405 The Harken air block offers a very high load in an extremely lightweight block. Excellent for control lines. The overall length is only 1-1/2" long. The 5/8" sheave will accept line as large as 7/32". 250 lb. SWL; 1200 lb. breaking strength.  The 16 mm is Harken’s smallest block. It is perfect for small synthetic control lines found on high-tech dinghies. The patented bearing system uses stainless steel balls in a captive grooved race and has a 250 lb.
    HARKEN 16MM BLOCK-BECKET
    Harken
    Harken 16mm Single Murrays Part# 28-0404 The Harken air block offers a very high load in an extremely lightweight block. Excellent for control lines. The block itself is only 1-1/8" long. The 5/8" sheave will accept line as large as 7/32". 250 lb. SWL; 1200 lb. breaking strength.
    HARKEN 16MM SINGLE
    Harken