Sailing Rudder & Foils

212 products

    212 products
    Rudder Stiffening Kit

Murrays Part# 001-2053

The Rudder Stiffening Kit for all Hobies eliminates excessive clearances between rudders and castings which cause wobble and thwart rudder alignment. Kit has 4 stainless nylock nuts and 8 spacers. Compare to Hobie Cat® item #136.
    RUDDER STIFFENING KIT
    Murrays Sports
    $7.00
    Hobie rudder bushing. Hobie part number 8062001
    RUDDER TITE BUSHING EACH
    Murrays Sports
    $5.50
    Murrays Part# 001-2050

The Hobie Rudder Cam Kit: Hobie 14, Hobie 16 are replacement rudder cams to keep the rudder lock-down mechanism on your Hobie Cat® functioning properly. The Hobie® 14 or 16 kit includes two cams, two reusable, internally threaded sister screws for both sides, and instructions. Purchase the complete kit if your boat has the stock flare pins; purchase just the cams (#50-10480000 each) if your boat already has sister screws. 

Compare to Hobie Cat® #5202.
    H-14/16 RUDDER CAM KIT
    Murrays Sports
    $52.00
    3/16 - 1/4" Split Ring
Murrays Part# 22-9492
Stainless steel split ring (ring ding) for 3/16″-1/4″ diameter clevis pin. This is the standard size Hobie split ring used all over the boats, most commonly on the shrouds, forestay and roller furler
Medium Split ring
Dimensions: 5/8″ Diameter
Material: 316 Stainless steel.
This is the most common size Split ring on Hobie, Nacra and Prindle Catamarans. 20860000 Medium Clevis Ring.
    3/16-1/4" SPLIT RING
    Misc
    $0.75
    RUDDER LOCKING KIT Hobie 16
Murrays Part# 50-10311900
Hobie factory rudder locking kit for Hobie 14 or 16 includes one each plunger, 2-1/2" spring (#50-10432000), and Delrin screw.
Delrin screw is 3/4-10 thread. In many cases you can drill it out with a 5/8" drill bit and then get a 3/4-10 tap to clear the threads.
    H14/16 RUDDER LOCKING KIT
    Hobie
    $29.99
    Aluminum Adjustable tiller extension for Hobie, Nacra and Prindle catamarans. Compare to Hobie 20550001 Hobie hot stick
    ALUMINUM TILLER EXTENSION 50"-95"
    Murrays Sports
    $89.00
    H17/18/20/21/Wave and Getaway
Rudder Cam Kit


Murrays Part# 001-3550



The Rudder Cam Kit: H17, H18, H20, H21, Wave, & Getaway are replacement rudder cams which help keep your Hobie’s rudder lock-down mechanism functioning properly. This kit includes sister screws to install the cams, making it easier to replace the cams. Purchase the complete kit if your boat has the stock flare pins; or you can purchase just the cams (#50-10480000 each) if your boat already has sister screws.
    H-17/18/20/21/WAVE AND GETAWAY RUDDER CAM KIT
    Murrays Sports
    $59.00
    Hobie Rudder Cam
Hobie part number 10480000
Hobie factory replacement cam. Rudder cams should be inspected and replaced periodically. Always replace cams that are bent out of shape.

Used on all Hobie Catamarans with metal housing rudder systems. Compatible on all Hobie 14, 16, 17, 18, 20, 21SC and 21SE as well as older Wave and Getaway models.

Not compatible with the Hobie Wave and Getaway EZ Loc plastic rudder housing rudder system.
    HOBIE RUDDER CAM
    Hobie
    $16.99
    RUDDER CASTING DELRIN SCREW - rudder locking adjustment screw - 60450000
    HOBIE DELRIN RUDDER SCREW
    Hobie
    $9.99
    Tiller Connection Kit
Murrays Part# 001-2061
The Murrays Tiller Connection Kit assures consistent rudder alignment through the full rudder sweep. Spring-loaded half balls and contoured spacers take the slop out of the tiller-to-crossbar connection on Hobie Cats. Racing class legal. Each kit contains 2 connectors to join the tiller crossbar to the tiller arms. Compare to Hobie Cat® #3052.
Applications:; Hobie 14, 16, 17, 18, 18SX
    TILLER CONNECTION KIT (PR)
    Murrays Sports
    $25.00
    Murrays Part# 001-0062
Replacement tiller yoke assembly for all hiking sticks sold by Murrays. Used to connect the tiller extension to the tiller crossbar. Includes two contoured spacers that provide a solid platform for the yoke to sit on. Compare to Hobie Cat® Tiller yoke assembly #3205 or NACRA connection part tiller/joystick #31072
Applications: All Hobies and Prindles
Tiller Yoke Assembly: 1
    TILLER YOKE ASSEMBLY WITH SPACERS
    Murrays Sports
    $14.99
    Cotter Pin 3/32 X 3/4
Murrays Part# 19-1015
Cotter pins are used on all Hobie, Nacra and Prindle rudder pins. They are used to secure the rudder pins. Compare to Hobie Cat® #8060111.
Stainless steel cotter pin measures 3/32" x 3/4".
    COTTER PIN 3/32 X 3/4" SS
    Misc
    $0.18
    RUDDER PINS H14/16 Stainless Steel

Murrays Part# 001-2269


Weight-saving, hollow stainless rudder pins for Hobie® 14 or Hobie® 16 with stronger .065" wall provide reduced wear and the best long-term fit. Includes one pair of 3/8" x 8" rudder pins with cotter pins.

These rudder pins are sold as a pair, whereas Hobie Cat® sells theirs individually as item #20880011.

New One piece rudder gudgeons have been produced with a slightly smaller metric hole size. If you have a 2020 and newer boat or 2020 and
    H-14/16 RUDDER PINS PR (SS)
    Murrays Sports
    $35.00
    RUDDER PINS W/BUSHINGS H14/16

Aluminum rudder pins for a Hobie 14 and 16. Includes cotter pins and 4 rudder bushings.

Hobie part numbers: 20880001 and 8062001
    H-14/16 RUDDER PINS WITH BUSHINGS
    Murrays Sports
    $45.00
    Murrays PN 001-0053

The Murrays Rudder Stiffening Spacer is a 2" diameter spacer for use on Hobie, Nacra and Prindle catamarans to eliminate excessive clearances between rudders and castings which cause rudder slop, side to side wobble, and thwart rudder alignment. A kit with spacers and nuts is also available (#01-2053).  The Murrays Rudder Stiffening Spacer are quite thin so that you can achieve a perfect fit. Standard kits come with 8 spacers.
    RUDDER STIFFENING SPACER
    Murrays Sports
    $0.75
    Rudder Pins H17/18 Stainless Steel

Murrays Part# 001-4273

Weight-saving compared to solid stainless steel pins, hollow stainless rudder pins with still beefy .065″ wall provide reduced wear and the good long-term durability. The universal stainless steel 3/8″ x 9-1/4″ rudder pins are suited for; Hobie 17/18/20 rudder castings. Also used on older Hobie Wave and Getaways with metal rudder castings.

Cotter pins are included.
Alternative to Hobie Cat® #60880011.  (* Pre EZ LOC Rudder c
    H-17/18 RUDDER PINS PR (SS)
    Murrays Sports
    $36.00
    Rudder Locking Kit Hobie 17, 18, 20, 21

Murrays Part# 001-3552



The Rudder Locking Kit Hobie 17, 18, 20, 21 includes the rudder spring, rudder casting screw, and the rudder plunger for the Hobie 17, 18, 20 and 21.


Delrin screw is 3/4-10 thread. In many cases you can drill it out with a 5/8" drill bit and then get a 3/4-10 tap to clear the threads.
    RUDDER LOCKING KIT - H-17/18/20 and 21
    Murrays Sports
    $38.19
    NACRA and Prindle Rudder Spring
Murrays Part# 56-4016
The NACRA and Prindle Rudder Spring is the rudder spring for all Prindle and most newer Nacras (Late Model US boats, Inters and all European NACRA boats) is Nacra Sailing factory item #30418.
Fits Nacra 460, Nacra 500, Nacra 570, Nacra 16, Nacra 17, Nacra F18 Infusion, Nacra F20 Carbon and all Inters.
    RUDDER SPRING
    NACRA
    $6.00
    Nut Nylock 5/16-18 Stainless Steel
Murrays Part# 19-2520
5/16-18 nylock nut is used on Hobie® rudders. The stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Compare to Hobie Cat® item #8050311 and 8050321 shroud anchor pin nut
Used with Hobie Getaway Bow Tang Bolt
    NUT NYLOCK 5/16-18 (SS)
    Misc
    $0.75
    The Murrays Hobie 16 one piece rudder gudgeon is not cast but machined and then anodized for superior strength and longevity.

Compare to Hobie 50102011
    The Murrays Hobie 16 one piece rudder gudgeon is not cast but machined and then anodized for superior strength and longevity.

Compare to Hobie 50102011
    MURRAYS H-16 ONE PIECE RUDDER GUDGEON
    Murrays Sports
    $89.99
    Retainer Clip EZ Lock Rudder Housing

Murrays Part# 50-90880231




Retainer clip for Hobie Bravo EZ Loc Rudder Housing.

Hobie Part# 90880231
    RETAINER CLIP EZ LOCK RUDDER HOUSING
    Hobie
    $5.99
    Out of Stock
    Hobie Wave Lower Pintle Bushing

Murrays Part# 50-38360001


This is the lower bushing for the original Wave or Getaway rudder castings. This fits into the aluminum rudder castings PRE- EZLoc rudder assemblies. This also fits Getaway and Bravo Pre-Ez Loc assemblies.

Hobie Part# 38360001
    HOBIE WAVE LOWER PINTLE BUSHING
    Hobie
    $5.99
    Rudder Casting Plunger H14/16
Murrays Part# 50-10440000
Hobie® factory replacement rudder casting plunger for Hobie® 14 or 16.
    H-14/16 RUDDER CASTING PLUNGER
    Hobie
    $6.99
    Hobie® factory replacement retainer clip for Hobie 20-style tiller connector and adjuster kit (#07-1953). TILLER CONNECTION RETAINER CLIP - HOBIE 20. 40590000 MURRAYS.COM - IN STOCK
    H-20 TILLER CONNECTOR RETAINER CLIP
    Hobie
    $5.99
    Hobie Tiller Extension Hinge

Murrays Part# 50-10532010

Hobie® factory replacement tiller extension hinge for #50-20550001 Hobie® Fiberglass tiller extension. Also used on Nacra tillers.

Hobie Part Number: 10532010
    HOBIE TILLER EXTENSION HINGE
    Hobie
    $17.99
    Tiller  Rudder Stiffening Kit: Prindle

Murrays Part# 001-5141



Spring-loaded tiller connection with contoured spacers tightens the hinge connection on Prindles. Six plastic shims reduce slop between rudders and castings
    PRINDLE TILLER AND RUDDER STIFFENING KIT
    Murrays Sports
    $19.95
    Rudder Cam Screws H17, H18, H20,
Older Wave and Getaway
Murrays Part# 001-3551
The Murrays Rudder Cam Pins are a pair of sister screws for use on the Hobie 17, 18, 20, 21, as well as the older Hobie Wave and Getaway rudder cams. These pins are an upgrade form the original stock hollow flare rivet that came on the Hobie. The Sister Screws are much easier to install and remove, and they are reusable.
Compare to Hobie Cat® #5203 and #50312301.
Sold in pairs
    H-17/18/20/OLDER WAVE AND GETAWAY RUDDER CAM PINS
    Murrays Sports
    $29.99
    Hobie Rudder Covers

Murrays PN 50-82420000

Rudder covers by Hobie protect your rudders from nicks and grime. Hobie's rudder covers feature straps with Fastex® fasteners to keep the covers firmly in place, even when trailering. The covers fit all Hobies except H21SE (Special Edition).

These come as a pair.

Hobie part number 82420000
    HOBIE RUDDER COVER
    Hobie
    $114.99
    Black Blue Red Orange
    POWERSTICK TELESCOPING CARBON TILLER 62-115" - YOKE STYLE
    Murrays Sports
    from $289.00
    H14/16/17/18 Gudgeon Lower

Murrays Part# 25-3352

The latest, strongest rudder gudgeon design with welded sleeve bushings provides large, smooth bearing surfaces between rudder pins and gudgeons. Replace flared gudgeons with their sharp edges and point loading that can cause early rudder pin failure. For Hobie® 14, 16 and 17, order separate upper and lower gudgeons. For all other Hobie® cats with new-style castings, post 1986, order 4 for a complete set .

Replacement for Hobie Part# 50101401
    H14/16/17/18 LOWER GUDGEON
    Murrays Sports
    $35.99
    Out of Stock
    H16/17/18 Tiller Crossbar-Post-1995

Murrays Part# 50-20521001



The Tiller Crossbar H16, H17, H18 Post-1995- is a Hobie® factory replacement tiller crossbar for 1995 and newer Hobie® 16, 17 or 18.

The Post 95 version comes with the new style quick connect tiller connection system.
    H-16/17/18 TILLER CROSSBAR-POST 1995
    Hobie
    $286.99
    Screw Delrin 3/8-16 X .75"

Murrays Part# 50-8032001

Hobie® factory replacement 3/8-16 x 3/4" Delrin screw is used as rudder rake adjustment screw on Pre-EZ Lock Rudder System.

Hobie Part# 8032001
    SCREW DELRIN 3/8-16 X .75"
    Hobie
    $5.99
    Hobie 18 rudder plunger. Hobie Part number 50312201. Also use on the 17 as well as the older Wave and Getaway
    H-17/18/GETAWAY RUDDER CAST PLUNGER
    Hobie
    $9.99
    Rudder Casting Lock Spring
Murray Part# 50-10430000
Hobie factory replacement 2-1/8" lock spring for rudder casting. Replace rudder springs with this original spring supplied on Hobie® 14, 16, (pre 1983) 17 and 18.
Compare to HC part number 10430000
H14, H16, H17, H18, H20
    HOBIE RUDDER SPRING
    Murrays Sports
    $9.99
    Replacement Sheave Prindle Rudder Upper

Ronstan PN RF1741




Replacement sheave for upper part of rudder casting on all models of Prindle catamarans. Replacement for Performance Sports item #4009. 1/4" wide x 3/4" diameter, 1/4" hole.
    ILLUSTRATED PRNDLE RUDDER PARTS LIST
    RONSTAN 19MM ACETAL SHEAVE, 6MM WIDTH
    Ronstan
    $3.50
    Rivet CCP 6-8 (3/16 X 1/2)
Murrays Part# 19-5033
Stainless steel 3/16" x 1/2" rounded pan head rivet. Compare to Hobie Cat® #8011231.
    RIVET CCP 6-8 (3/16 X 1/2)
    Misc
    $0.85
    H14/16 Upper Gudgeon

Murrays Part# 25-3351

This latest, strongest design with welded sleeve bushings provides large, smooth bearing surfaces between rudder pins and gudgeons. Replace flared gudgeons with their sharp edges and point loading that can cause early rudder pin failure. For Hobie® 14's, 16's and 17, order separate upper and lower gudgeons.

 For all other Hobie® cats Part# 25-3352 for both gudgeons. Each

This gudgeon is a replacement for item #50101301
    H-14/16 UPPER GUDGEON
    Murrays Sports
    $19.99
    Hobie 1953 tiller connection kit - new style
    H-20 TILLER CONNECTOR
    Hobie
    $240.99
    H14/16 Rudder Return Hand Shock Cord

Murrays Part# 001-2240

Two 32" shock cords with balls keep your Hobie® 14 or 16 rudders down when the cams don't! Order Kisme Kleets #05-1010 separately, if needed.
    H-14/16 RUDDER RETURN HAND SHOCK CORD
    Murrays Sports
    $8.50
    Rudder Pins H17, H18, Wave, Getaway (Aluminum)
Murrays Part# 001-4274
Aluminum rudder pins for the Hobie 17, 18, Wave and Getaway.  Aluminum 3/8″ x 9-1/4″ rudder pins, cotter pins are included. 

Sold in pairs

Compare to Hobie Cat® #60880001
    H-17/18/WAVE AND GETAWAY ALUMINUM RUDDER PINS
    Murrays Sports
    $30.00