All Sailing Parts

All Sailing Parts

2262 products

Everything Nacra, Prindle, Hobie and a few more fun odds and ends.

2262 products

Sort

Daggerboard Carpet

Murrays Part# 56-1082

Approximately 1-1/2″ wide carpet installs in daggerboard wells.

Nacra factory item #1083.

Sold by the foot.

DAGGERBOARD CARPET

Hobie Cat 8010181 Rivet

RIVET CCP SEALED 6-4 (3/16 X 1/4)

H14/16 Bow Tang

Murrays Part# 50-20120000

Hobie® factory replacement bow tang for Hobie® 14, 16 or Getaway. Use #19-3530 screw and #19-2520 nylock nut on Hobie 16; use #19-3530 screw on Hobie 14.

The original Hobie® 14 tang is no longer available.
20120010

Hobie factory replacement bow tang for Hobie 14, 16 or Getaway. Use #19-3530 screw and #19-2520 Nylock nut on Hobie 16;

use #19-3530 screw on Hobie 14.

The original H14 tang is no longer available.

Hobie Part# 20120000 and 20120010

H-14/16 BOW TANG

Nut Nylock 5/16-18 Stainless Steel
Murrays Part# 19-2520
5/16-18 nylock nut is used on Hobie® rudders. The stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Compare to Hobie Cat® item #8050311 and 8050321 shroud anchor pin nut
Used with Hobie Getaway Bow Tang Bolt

NUT NYLOCK 5/16-18 (SS)

The Murrays Jib Snorkel will protect your roller furling jib from ultraviolet light and weather while on or off the boat.

MURRAYS JIB SNORKEL

Murrays red, green and blue tell tails. Sail trimming guides.

MURRAYS TELL TAIL SET

3/16" Split Ring - 7/16″ Diameter
Murrays Part# 22-9490
Stainless steel split ring for 1/8-3/16″ diameter clevis pins. Comparable to Hobie Cat® #81503100 Small Clevis Ring. This is a super small size, best for locations where you may be concerned about it snagging on something. The small size helps prevent it from snagging on lines, sheets, sails and clothing.

3/16" SPLIT RING

Batten Cap Hobie Main Leech
Murrays Part# 50-11323000
Hobie® factory replacement part number 11323000.
Hobie batten cap are sold individually.
Order batten tie separately; 18" of 1/8" line per batten cap is standard.
Sold individually

HOBIE MAIN LEECH BATTEN CAP

Alpha SSR 8mm Racing Sheet - main sheet

5/16" SSR RACING SHEET 8MM

Wave Shroud 1/8" Black Wire

Murrays Part# 002-0804-02

Single black shroud (sidestay) for Hobie® Wave is constructed to factory specifications.

Compare to Hobie Part# 39790001

WAVE SHROUD 1/8" BLACK WIRE

Wave Forestay 1/8" Black
Murrays Part# 002-0844-02
One black forestay for Hobie® Wave is constructed to factory specifications. Compare to Hobie Cat® #39810001.

WAVE FORESTAY 1/8" BLACK WIRE

Prindle New Rubber Hull Plug

Murrays Part# 56-1015

Solid rubber hull plug for Prindle's fits into 1-5/8″ diameter hole. This part is not as clean of a fit as the original part. Some silicone may help with placement.

Nacra Sailing factory item #30378

PRINDLE NEW RUBBER HULL PLUG

RIVET CCP 6-6 (3/16 X 3/8)
Murrays Part# 19-5032
Stainless steel 3/16" x 3/8" pan head rivet
Among other uses, the Stainless steel 3/16" x 3/8" pan head rivet can be used when Hobie® rivet #8010131 is specified:
Hobie 14 (2) or 16 (4) mast head
Hobie Wave/Getaway/14/16/17/18/18SX/ mast base (4)
Hobie 14/16 rudder upper casting (2)
Hobie 14/16 tiller end cap (2)
Hobie 14/16 boom front end cap (3)
Pair with stainless steal rivet casings to seal the holes when using on the mast.

RIVET CCP 6-6 (3/16 X 3/8)

Hobie Shroud Anchor Bar

Murrays Part# 50-50101701

This is the bar that the shroud anchor pins screws into to secure the shrouds on. Shroud anchor bar for Hobie Cat masts (replaces the nut used on older models). Use with the anchor pin to secure under the lip of the hull.

Stainless steel
Length: 3.5 inches
Application: Hobie 14/16/17/18 sailboats

Compare to Hobie Part# 50101701

HOBIE SHROUD ANCHOR BAR

Hobie 1953 tiller connection kit - new style

HOBIE TILLER CONNECTOR KIT

Main Halyard Ring (Murrays)

Murrays Part# 001-4216

If you're having trouble raising or lowering your mainsail due to a faulty halyard ring and shackle, this upgrade will help. Welded ring and lanyard give you more positive control while hooking or unhooking the ring to the hook. Use on any boat that uses a hook at the mast head and a ring and shackle at the head of the sail. Personal preference dictates whether you choose this ring or the Hobie Aussie Ring (#07-3064).

This item replaces discontinued Part

MAIN HALYARD RING (MURRAYS)

H14/16 6:1 Downhaul Kit
Murrays Part# 007-2089-1
This Class-legal, complete 6:1 downhaul kit for Hobie 14 or 16 comes with Harken Carbo blocks. 

Includes: Class-approved mast track attachment, all hardware and line.

Recommended for use with gooseneck bearing kit (#012-2050)

Hobie Part# 2089

Downhaul Kit: 6:1 Hobie 14/16
This Class-legal, complete 6:1 downhaul kit for Hobie 14 or 16 comes with Harken Carbo blocks.
Includes: Class-approved mast track attachment, all hardware and line.
Recommended for use with gooseneck bearing kit (#012-2050).
Hobie part number 2089

H-14/16 6:1 DOWNHAUL KIT

Murrays Part# 001-1195WH

5" Flat Access Port

The 5" Flat Access Port is designed to install on a flat surface. Each hatch includes one deck ring and one lid. A lip accommodates a Cat Bag (sold separately). For Hobie® 20 and Tiger. This also fits the NACRA 15 and fits much like the VIKING access ports. Customers tend to prefer this style to the ports that became stock in 2018. Does not include hardware, hardware options shown in the related items section below.

Compare to NACRA part number 30365

Compare

5" PORT FLAT SCREW WITH LIP WHITE

Dacron Spun Braid 3/8″

The Dacron Spun Braid 3/8″ is very low-stretch sheeting line and has a soft, fuzzy surface that offers excellent grip and make it easy on the hands. It features a 100% polyester braided core with a spun polyester braided cover. The 3/8″ diameter is ideal for mainsheets on Hobies, Nacra and Prindle Catamarans. Sold per foot. Spools come in 600′. We recommend Dacron Spun Braid line for recreational cat sailors, it has a nice hand feel, cleats well and runs thru the blocks well. D

3/8" DACRON SPUN BRAID 9MM

EZ-UP TRAP KIT: HARKEN - similar to Hobie part number 3102

EZ-UP TRAPEZE KIT

Hobie 18 rudder plunger. Hobie Part number 50312201. Also use on the 17 as well as the older Wave and Getaway

H-17/18/GETAWAY RUDDER CAST PLUNGER

Rudder Casting Plunger H14/16
Murrays Part# 50-10440000
Hobie® factory replacement rudder casting plunger for Hobie® 14 or 16.

H-14/16 RUDDER CASTING PLUNGER

Hobie 18 shroud - side stay - Hobie part number 6079001 white and 60792001 black

H-18/21 SC SHROUD 5/32" ROLLER SWAGED

The Hobie 18 Trapeze Shock Cord is an absolute necessity because it keeps the trapeze system in place and ready for hook-up. On this kit for Hobie® 18, one hook connects to either the thimble on the trapeze wire or the adjustment line, then runs through the hull fairlead and through the eyestrap under the lip of the hull near the bow or stern for crew and skipper trapeze lines respectively. The 3/16" shock cord stretches more and slides through ferrules better than larger diameter shock cord. Includes four

H-18 TRAP SHOCK CORD (4)

Hobie 16 Batten Tie Set

Murrays Part# 001-3816

4 x jib batten ties and 8 main sail batten ties.

H-16 BATTEN TIE SET

Tiller Rudder Stiffening Kit: Prindle

Murrays Part# 001-5141

Spring-loaded tiller connection with contoured spacers tightens the hinge connection on Prindles. Six plastic shims reduce slop between rudders and castings

PRINDLE TILLER AND RUDDER STIFFENING KIT

The Murrays Rudder Cam Sister Screws: Hobie 14, Hobie 16 are a pair of sister screws for Hobie 14 and 16 rudder cams. These pins are much easier to install and remove than the stock pin and they are reusable! Sold in pairs

Hobie Cat Part# 10470000

Hobie Part# 5201

The Murrays Rudder Cam Sister Screws: Hobie 14, Hobie 16 are a pair of sister screws for Hobie 14 and 16 rudder cams. These pins are much easier to install and remove than the stock pin and they are reusable! Sold in pairs

Hobie Cat Part# 10470000

Hobie Part# 5201

H-14/16 RUDDER CAM SISTER SCREWS

Hobie EZ Lock Rudder retainer clip

Murrays Part# 50-90880231

Retainer clip for Hobie Bravo EZ Loc Rudder Housing.

Hobie Part# 90880231

HOBIE EZ LOCK RUDDER CLIP

H14 Shroud 1/8"

One shroud (sidestay) for Hobie® 14 constructed of 1/8" wire to factory specifications.

Connect at top with #21-0635 1/4" bow shackle; connect to stay adjuster with #22-9802 clevis pin.

Use this page to order product numbers:

02-0104-01 White
02-0104-02 Black

Hobie Cat® Part# 10792100

H-14 SHROUD 1/8" WIRE

The Murrays Hobie 16 Jib Halyard Tension Kit allows sailors to quickly and easily adjust their jib halyard tension while under way.  This allows sailors to adjust their mask rake and rig tension to suit the conditions.

H-16 JIB HALYARD TENSION KIT

RIVET MCP 6-8 3/16x1/2" PH
Murrays Part# 50-8011231
Hobie® factory 6-8 heavy duty rivet requires a rivet tool for installation. 3/16" x 1/2" pan head.
Fits Hobie Getaway Eyelet Post.
Fits Hobie 20 Eyelet Post.
Mounts Wave Mast Step
Hobie part number 8011231

RIVET MCP 6-8 3/16x1/2" PH

The Selma fid (needle) is the only tool for splicing all kinds of rope. Selma fids are made of highly polished stainless steel. Made in Norway and patented worldwide.

Please note that the appropriate fid size will depend on the type and construction of line. The purchase of a set of 4 or 5 fids may be a better option if you are unsure of the fid size you need.

SELMA FID 4.0mm 1/8-1/4"

Cat Trax Tire Tubes

Murrays Part# 13-1401-9

Add an inner tube to the tire(s) of your Cat Trax beach dolly to prevent air leaks or squeeze some life out of your old tires.

Sold individually

CAT TRAX TIRE TUBE

Sail/Kite Repair Tape – Cut the needed amount off the 25-foot, 2″-wide roll of repair tape and keep the rest handy for emergencies. The 3/4-oz. ripstop nylon is self-adhesive and easy to apply for repairs to sails and kites. Compare to Hobie Cat® #1662.

SAIL/KITE REPAIR TAPE

Righting Bag Only (200+LBS)

Murrays Part# 001-3282

This is the bag only from Murrays' popular Cat Righting Big Bag System (#01-3280). The 18" x 32" bag attaches with hook and loop straps under the tramp for easy use and storage. The theoretical maximum capacity of the bag is 250 lbs.

RIGHTING BAG ONLY (200+LBS)

Clevis Pin 1/4X3/8

Murrays Part# 50-8020371

This is commonly used for Hobie Rigging parts. It has a 3/8" grip length. You can also use the 1/2" grip length pins also.

Hobie Part# 8020371 or 8020370

CLEVIS PIN 1/4 x 3/8"

MAST HINGE PIN NACRA/H17/20
Murrays Part# 56-F158
The mast base engages the mast ball and is secured by this headless clevis pin to allow the mast to be safely raised or lowered.
Specs: 1/4" diameter x 2-3/8" overall length with a grip length of 1-15/16"
Compatibility: Nacra Inter, F18, N15, F17, 4.5/450, 5.0, 5.2, 5.5SL, 5.7, 5.8NA, 6.0NA, 5.5UNI and 18SQ, as well as Hobie 17, Tiger and 20. Split rings are sold separately.
Compare to Hobie Cat part number 50406301.

NACRA MAST HINGE PIN

Spring Clip 1/4-5/16"

Murrays Part# 25-2204

Use this 316 stainless spring clip for quick rudder pin removal or on 1/4" to 5/16" pins. This handy little pin is also called a hairpin cotter, bridge pin, hitch pin clip or R clip. Great convenience item for all boats with rudder pins, ie: Hobie 14, 16, 17, 18, 20, Prindle 15, 16, 18, 18-2, 19, 19MX, and Escape.

Spring Clip: 1/4-5/16

Murrays Part# 25-2204

Use this stainless spring clip for quick rudder pin removal or on 1/4" to 5/16" pins. This handy little pin is also called a hairpin cotter, bridge pin, hitch pin clip or R clip. Great convenience item for all boats with rudder pins, ie: Hobie 14, 16, 17, 18, 20, Prindle 15, 16, 18, 18-2, 19, 19MX, and Escape.

SPRING CLIP 1/4 - 5/16"

Rudder Pins H17/18 Stainless Steel

Murrays Part# 001-4273

Weight-saving compared to solid stainless steel pins, hollow stainless rudder pins with still beefy .065″ wall provide reduced wear and the good long-term durability. The universal stainless steel 3/8″ x 9-1/4″ rudder pins are suited for; Hobie 17/18/20 rudder castings. Also used on older Hobie Wave and Getaways with metal rudder castings.

Cotter pins are included.
Alternative to Hobie Cat® #60880011.  (* Pre EZ LOC Rudder c

H-17/18 RUDDER PINS PR (SS)

H-18/20 JIB HALYARD WITH CLIP

Previous 1 2 3 4 5 6 … 57 Next

Recently viewed

All Sailing Parts