NACRA

331 products

    331 products
    Mast Ball 1.5" (Nylon) Murrays Part# 56-2504 This larger mast ball for post-1983 Nacras. Ball measures 1-1/2" diameter with a 9/16"-18 threaded hole. Nacra Sailing factory item# 30338 and 30062
    NACRA MAST BALL 1.5" (NYLON)
    NACRA
    Mast Bearing Half Round Murrays Part# 56-2007 Half-round mast bearing for all Prindle mast steps. Nacra Sailing factory item# 30964
    PRINDLE MAST BEARING HALF ROUND
    NACRA
    MAST HINGE PIN NACRA/H17/20 Murrays Part# 56-F158 The mast base engages the mast ball and is secured by this headless clevis pin to allow the mast to be safely raised or lowered. Specs: 1/4" diameter x 2-3/8" overall length with a grip length of 1-15/16" Compatibility: Nacra Inter, F18, N15, F17, 4.5/450, 5.0, 5.2, 5.5SL, 5.7, 5.8NA, 6.0NA, 5.5UNI and 18SQ, as well as Hobie 17, Tiger and 20. Split rings are sold separately. Compare to Hobie Cat part number 50406301.
    NACRA MAST HINGE PIN
    NACRA
    Prindle New Rubber Hull Plug Murrays Part# 56-1015 ​Solid rubber hull plug for Prindle's fits into 1-5/8″ diameter hole. This part is not as clean of a fit as the original part. Some silicone may help with placement. Nacra Sailing factory item #30378
    PRINDLE NEW RUBBER HULL PLUG
    NACRA
    NACRA and Prindle Rudder Spring Murrays Part# 56-4016 The NACRA and Prindle Rudder Spring is the rudder spring for all Prindle and most newer Nacras (Late Model US boats, Inters and all European NACRA boats) is Nacra Sailing factory item #30418. Fits Nacra 460, Nacra 500, Nacra 570, Nacra 16, Nacra 17, Nacra F18 Infusion, Nacra F20 Carbon and all Inters.
    ILLUSTRATED PRNDLE RUDDER PARTS LIST
    NACRA/PRINDLE RUDDER SPRING
    NACRA
    End Cap With Hole Murrays Part# 56-2503 Nacra crossbar end cap. Used on all Nacras with round crossbars. Pictured with hole. Nacra front crossbar end cap with hole part #2503, rear crossbar end cap without hole part #3503  Compatible with Nacra 4.5, 450, 5.0, 5.2, 5.5SL, 5.7, 5.8NA, 6.0NA, 5.5UNI, and 18SQ
    NACRA END CAP WITH HOLE
    NACRA
    Mast Base Casting Murrays Part# 56-6005 Mast base casting for Prindle 16 Nacra Sailing factory item# 30442
    PRINDLE 16 MAST BASE CASTING
    NACRA
    Rudder Locking Bolt Murrays Part# 56-4017 The Prindle Rudder Locking Bolt is the factory replacement bolt for rudder locking system on all Prindles. Tip: Be sure to check for proper alignment of the lock bolt to spring bolt. Any bent component will prevent the system from working properly. Identify and replace the bent portion to get your rudder system functioning properly. Performance Sports factory item# 4017
    PRINDLE RUDDER LOCKING BOLT
    NACRA
    Clevis Pin 1/4 X 3/4" Murrays Part# 56-4012 The Clevis Pin 1/4 X 3/4" is used on Prindle rudders, Nacra mast head sheave and as Nacra/Prindle shroud pin. Prindle Part# 4012
    CLEVIS PIN 1/4 X 3/4"
    NACRA
    Jib Halyard "S" Hook Murrays Part# 56-9839 The Prindle Jib Halyard "S" Hook is a welded stainless "S" hook for Prindle-style jib halyards. Nacra Sailing factory item #30507. Performance sailing part# 9839 Nacra Sailing factory item# 30507
    PRINDLE JIB HALYARD "S" HOOK
    NACRA
    Traveler Car Murrays Part# 56-3010 The Prindle Traveler Car is standard equipment on all models of the latest Prindle® cats. Four durable plastic rollers ride smoothly on Prindle® traveler tracks. Two cylindrical sheaves reduce traveler control line friction. Performance Sports factory item# 3010
    PRINDLE TRAVELER CAR
    NACRA
    Out of Stock
    Nacra Tiller Tie Bar End Tendon Assembly Murrays Part# 56-31567-2 The rubber tiller tiebar connection including string. This part connects the tillerarm with the tiller crossbar.
    NACRA TILLER TIE BAR END TENDON ASSEMBLY
    NACRA
    Nacra Main Halyard Ring with Shackle Murrays Part# 56-30312 This shackle connects your Mainsail on your mast, it's knotted on your main halyard. It takes your Mainsail through the slot of your mast to the top where it connects with the Mainsail hook.
    NACRA MAIN HALYARD RING WITH SHACKLE
    NACRA
    Trampoline Slug Slide Murrays Part# 56-9892 Use for lacing tramp to rear crossbar to eliminate the need for an aft lacing strip. The slug can also be used in sail track. Used on the Hobie Getaway and Hobie 21SC forward trampolines Hobie Part # 96280000
    NACRA TRAMPOLINE SLUG SLIDE
    NACRA
    Half Round Load Spreader Murrays Part# 56-4019 This component is installed into the head of the rudder blade to anchor the rudder locking pin. The Prindle Half Round Load Spreader is for rudder system on all Prindles. Prindle Part# 4019 Nacra sailing factory item# 30973
    PRINDLE HALF ROUND LOAD SPREADER
    NACRA
    Prindle Rudder Lower Plastic Spacer Murrays Part# 56-4014 Prindle Rudder Lower Plastic Spacer is used on the rudder systems of all Prindle models. Performance Sports factory item #4014. 9/16″ wide x 1/2″ diameter, 1/4″ hole.
    ILLUSTRATED PRNDLE RUDDER PARTS LIST
    PRINDLE LOWER RUDDER PLASTIC SPACER
    NACRA
    Upper Rudder Roller Murrays Part# 56-4009 This plastic spacer/ roller is used in the locking mechanism of Prindle Rudder systems. It is also used as a boom roller.
    PRINDLE UPPER RUDDER ROLLER
    NACRA
    Nylon Washer Internal Casting Prindle Murrays Part# 56-F118 Nylon washer is used on Prindle rudder casting to separate the upper sheaves to help keep the line from fouling. Order four per side to remove as much slop as possible. Performance Sports factory item #F118
    PRINDLE NYLON WASHER INTERNAL CASTING
    NACRA
    4" ALUMINUM BAR FOR BOW TANG Bow tang support rod for Prindle catamarans. Aluminum bar for bow tang on Prindle 15, 16 and 18 is Nacra Sailing factory item #30387.
    PRINDLE 4" ALUMINUM BAR FOR BOW TANG
    NACRA
    Nacra Rear Beam Tramp Tie Buttons Murrays Part# 56-30883 The NACRA Rear Beam Tramp Tie Buttons are the black nubs that are riveted on to the rear beam to hook the tramp lacing around. These are used on many boats and are installed with a 3/16 1/2" rivet. These can likely also be used on a Hobie Getaway, Miracle 20 or others that are looking to use a smaller Dyneema line instead of the 3/16 or 5/32 line Nacra Part# 30883
    NACRA REAR BEAM TRAMPOLINE TIE BUTTONS
    NACRA
    Tiller Tie Bar Kit Murrays Part# 56-5516 The Nacra Tiller Tie Bar Kit provides improved tiller connect for older Nacras. Nacra Sailing factory item# 30149 and 30150
    NACRA TILLER TIE BAR KIT
    NACRA
    Nacra Rudder Blade Cushion Use these cushions to trim your rudder blades in the casting.
    NACRA RUDDER BLADE CUSHION
    NACRA
    NACRA URETHANE TILLER TIE BAR ROD WITH STRING
    NACRA
    Nacra Mast Ball 1-1/4" Old (Nylon) Murrays Part# 56-C601 This is the smaller, 1-1/4" mast ball for older, pre-1983 Nacra 5.0, 5.2 and 5.8. Hole diameter is 1/2".
    NACRA NYLON MAST BALL 1-1/4" OLD STYLE
    NACRA
    Spreader Tip Cover Murrays Part# 56-9862 These vinyl spreader bar end covers are real sail-savers! The smooth, resilient cover protects the jib luff from wear and tear from cotter keys and sharp edges. Nacras (except original 5.2 with non-adjustable spreaders) and Prindles. Nacra Sailing factory replacement item# 30322
    NACRA SPREADER TIP COVER
    NACRA
    Tiller Tie Bar Fitting with Tendon Murrays Part# 56-4536 Tiller tie bar fitting with tendon fits all Inters
    NACRA TILLER TIE BAR FITTING WITH TENDON
    NACRA
    Rear Boom End Cap Murrays Part# 56-7903 Rectangular rear boom end cap casting for Nacra 5.2 and all Prindles. Nacra Sailing factory item# 30205
    NACRA/PRINDLE REAR BOOM END CAP
    NACRA
    NACRA 15/F16/17/F20C BRIDLE CONNECTOR
    NACRA
    NACRA MAST CAUTION LOGO STICKER
    NACRA
    Out of Stock
    Nacra Spinnaker Tapered Halyard Murrays Part# 56-50011 Spihalyard tapered Nacra F18 Infusion (red/white), , has a SSR basics, made by Alpha Ropes. Looking to the construction of the line, it's single braid, 16 strand (8x2), mix Dyneema® Sk78 / Cordura®. This line is not ready for kinking and is excellent for sheets. A advantage of this line, its soft while kept in your hands. The spihalyard is ready to sail, completed with tapering for less resistance while hosting/dropping.
    NACRA SPINNAKER TAPERED HALYARD
    NACRA
    Inter Downhaul S Hook Murrays Part# 56-9651 ​The Nacra Inter Downhaul “S” Hook is a down haul hook for all Nacra Inter catamarans. Performance Sports factory Part# 9651
    NACRA INTER DOWNHAUL S HOOK
    NACRA
    Tiller Joint- 3" Urethane Rod Murrays Part# 56-4588 The Nacra Tiller Joint - 3" Urethane Rod is for tiller connections on all Inters, the 500, 570, F18 Infusion and more. The part must be drilled to match your application. Compare to Nacra Part# 4588
    NACRA TILLER JOINT- 3" URETHANE ROD
    NACRA
    Prindle Rudder Lock Bolt Nut Murrays Part# 56-4018 The Prindle Rudder Lock Bolt Nut is the factory replacement 3/8″ hex nut for rudder lock bolts on all Prindles. Also used as the jam nut for adjuster screw on Nacra bridle foil assembly. Nacra Sailing factory item #30420. Prindle part number 4018
    Prindle rudder parts 4000, 4001, 4002, 4004, 4005, 006, 4007, 4009, 4012, 4010, 4014, 013, 4016, F115, F120
    PRINDLE/NACRA RUDDER LOCK BOLT NUT
    NACRA
    NACRA BOOM PIN
    NACRA
    Out of Stock
    Nacra Tapered Mainsheet with Splittale 1:10 Murrays Part# 56-50017 The N15 Tapered Mainsheet w/ Splittale 10:1 has a D cup kmix basics, made by Alpha Ropes. The construction of the line is double braid, 12 strand coated, Dyneema® Sk78 core, 24 plait mix with a HT Polyester / Cordura cover.
    NACRA TAPERED MAINSTEET WITH SPLITTALE
    NACRA
    Jib Track End Stop Murrays Part# 56-1911 1 Jib track end stop. Fits Nacra 5.5SL, 5.7, 5.8, 6.0, as well as Prindle 18-2 and 19.
    PRINDLE/NACRA JIB TRACK END STOP
    NACRA
    Carbon Mast Head Murrays Part# 56-6602CAR Nacra mast head for a carbon mast. Nacra Part# 6602Car
    NACRA CARBON MAST HEAD
    NACRA
    Nacra Inter 20 Tiller Arm Murrays Part# 56-4583 Tiller arm for the Inter 20. Nacra Part# 30124
    NACRA INTER 20 TILLER ARM
    NACRA
    Nacra Spinnaker Pole Rear End Cap Murrays Part# 56-9625 Use to attach spinnaker pole to boat. Outside diameter of cap is approximately 1-5/16". Fits: Nacra 460, Nacra 500, Nacra 570, Nacra 16, NACRA 17, Nacra F18 Infusion, Nacra F20 Carbon FCS Nacra Sailing factory item# 30775
    NACRA SPINNAKER POLE REAR END CAP
    NACRA
    Out of Stock
    Nacra Daggerboard Rubber Holder Murrays Part# 56-30014 Replacement dagger board rubber holder for NACRA boats with a dagger board. Specs: 3/4 x 2" Nacra Part# 30014
    NACRA DAGGERBOARD RUBBER HOLDER
    NACRA
    Recently viewed