Hobie, Nacra, Prindle sails and sail accessories

Sails & Accessories

184 products
    184 products
    Out of Stock
    3/16 - 1/4" Split Ring Murrays Part# 22-9492 Stainless steel split ring (ring ding) for 3/16″-1/4″ diameter clevis pin. This is the standard size Hobie split ring used all over the boats, most commonly on the shrouds, forestay and roller furler Medium Split ring Dimensions: 5/8″ Diameter Material: 316 Stainless steel. This is the most common size Split ring on Hobie, Nacra and Prindle Catamarans. 20860000 Medium Clevis Ring.
    SPLIT RING 3/16-1/4"
    Misc
    The Murrays Hobie 16 main halyard for is constructed to factory specifications with a long rope section and a shorter wire section with a stopper and halyard shackle. 20617001
    H-16 MAIN HALYARD COMPTIP
    Murrays Sports
    Hobie Cat #80550005 Main sail batten pocket protector kit. Hobie, Nacra, Prindle.
    SAIL POCKET PROTECTOR KIT MAIN
    Murrays Sports
    1/4" Bow Shackle Ronstan PN RF635
    1/4" BOW SHACKLE
    Ronstan
    Ronstan Stainless Steel Bow Shackle, 3/16" Pin, Coined Head Murrays Part# 21-0634 Solid stainless steel bow shackle has 3/16" diameter pin.  UDL BL - The “Uniformly Distributed Load” breaking load of the shackle; the load is applied across the full span of the shackle pin. PL BL - The “Point Load” breaking load of the shackle; the load is only applied at the center or one side of the shackle pin.
    RONSTAN STAINLESS STEEL BOW SHACKLE, 3/16" PIN, COINED HEAD
    Ronstan
    JIB HANK H-16 & SOL CAT
    Hobie
    Hobie 16 Main Halyard with Shackle is a wire halyard for the all-aluminum mast (no Comp-Tip) Hobie 16 and is used to raise the main sail. Compare to Hobie Cat® #20651011
    H-16 MAIN HALYARD WITH SHACKLE
    Murrays Sports
    Downhaul Kit: 6:1 Hobie 14/16 Murrays Part# 007-2089 This Class-legal, complete 6:1 downhaul kit for Hobie 14 or 16 comes with Harken Carbo block. Includes Class-approved attachment for base of mast, all hardware and line. Use with gooseneck bearing kit (#12-2050). Hobie Part# 2089
    Downhaul Kit: 6:1 Hobie 14/16 Murrays Part# 007-2089 This Class-legal, complete 6:1 downhaul kit for Hobie 14 or 16 comes with Harken Carbo block. Includes Class-approved attachment for base of mast, all hardware and line. Use with gooseneck bearing kit (#12-2050). Hobie Part# 2089
    DOWNHAUL KIT 6:1 H14/16
    Murrays Sports
    Batten Cap Hobie Main Leech Murrays Part# 50-11323000 Hobie® factory replacement part number 11323000. Hobie batten cap are sold individually. Order batten tie separately; 18" of 1/8" line per batten cap is standard. Sold individually
    HOBIE MAIN LEECH BATTEN CAP (EA)
    Hobie
    The Murrays main halyard for Hobie Wave is constructed with 1/4" polyester yacht braid line and 316 stainless wire finished with a halyard shackle with a captured pin, Built to factory specifications. A main halyard is used to raise the main sail. Compare to Hobie part number 38651001. 
    WAVE MAIN HALYARD
    Murrays Sports
    Hobie 16 Super Flex Jib Batten Set Hobie part number 0122
    MURRAYS H16 SUPER FLEX JIB BATTEN SET
    Murrays Sports
    Getaway Main Halyard Murrays Part# 002-0973-60 The Murrays Hobie Getaway main halyard for is constructed to the current factory specs. It has a long rope section and a shorter wire section with a stopper and halyard shackle. The rope section is easy on the hands and prevents electrical current from traveling down the mast in the event of an electrical wire contact.
    GETAWAY MAIN HALYARD
    Murrays Sports
    Ronstan Stainless Steel D Shackle, 3/16" Pin, Slotted Head Murrays Part# 21-0616 Ronstan stainless D shackle has 3/16" diameter pin. This shackle is a substitute for Hobie® item #11220000, #SP0051 and #SP0052.
    RONSTAN STAINLESS STEEL D SHACKLE, 3/16" PIN, SLOTTED HEAD
    Ronstan
    Murrays Deluxe Sail and Boom Bag - Will fit any Hobie sail, compatible with all Nacra and Prindle sails as well. The Hobie 16 has the widest sail of any Hobie and at a width of 109″
    Murrays Deluxe Sail and Boom Bag - Will fit any Hobie sail, compatible with all Nacra and Prindle sails as well. The Hobie 16 has the widest sail of any Hobie and at a width of 109″
    Murrays Deluxe Sail and Boom Bag
    Murrays Sports
    Murrays Tell Tails Pack of 16 Murrays PN 001-3825 Black ripstop nylon tell-tales attach to the sail with adhesive patches to visually aid in trimming the sail.  Compatible with both the main and jib sails. Set includes: 6 x pairs of Black tell tails 4 x Black Leech tell tails
    MURRAYS TELL TAIL SET
    Murrays Sports
    Tack Clew Plate Replacement Kit Murrays Part# 001-1016 ​The Tack & Clew Plate Replacement Kit includes one pair anodized aluminum plates with rivets to be set with a hammer. Rounded triangular plates measure 2-1/2″ by 2-1/2″ by 3″. Replacement rivets are available separately (#19-5005). These are commonly used as the H16 main sail clew plate and tack plate on older H16 sails. Newer sails use a hydraulic press ring at the tack and clew. Compare to Hobie part number 12240000.
    TACK/CLEW PLATE REPL KIT
    Murrays Sports
    Harken 22mm Block Murrays Part# 28-0224 This Harken ball bearing micro single block with stainless side plates is a small block with high load capabilities. It is a premium quality block for your trapeze return system.
    HARKEN 22MM BLOCK
    Harken
    H14/16 6:1 Downhaul Kit Murrays Part# 007-2089-1 This Class-legal, complete 6:1 downhaul kit for Hobie 14 or 16 comes with Harken Carbo blocks.  Includes: Class-approved mast track attachment, all hardware and line. Recommended for use with gooseneck bearing kit (#012-2050) Hobie Part# 2089
    Downhaul Kit: 6:1 Hobie 14/16 This Class-legal, complete 6:1 downhaul kit for Hobie 14 or 16 comes with Harken Carbo blocks. Includes: Class-approved mast track attachment, all hardware and line. Recommended for use with gooseneck bearing kit (#012-2050). Hobie part number 2089
    H-14/16 6:1 DOWNHAUL KIT
    Murrays Sports
    Batten Caps Luff H16 Jib (Pack of 4) Hobie Part# 012-3006 No more battens poking through next to the mast. This Tren Tec item includes four Hobie® 16 jib luff batten caps to prevent batten splitting and align batten to the angle of the sail, increasing the life of your sail. Glue to the forward end of the batten. Hobie Cat® uses #1566 for this item
    LUFF CAPS H-16 JIB (4)
    Tren-Tec
    Use this 1/8″ Dacron line for batten tie line and roller furling systems. For batten ties, allow about 18″ of line for each batten. Sold per foot. Spool: 1000′ (304.9m). Compare to Hobie part number RH112WHT - 8004510
    DACRON SOLID BRAID 1/8" WHITE
    Misc
    Sail Pocket Protector Kit Jib Murrays Part# 001-1002 The Jib Sail Pocket Protector Kit includes one pair of tough nylon protectors with indentations for included rivets that are set with a hammer.
    SAIL POCKET PROTECTOR KIT JIB
    Murrays Sports
    SAIL & BOOM BAG "Big Dryer"
    Murrays Sports
    H-18/20 JIB HALYARD W/CLIP
    Murrays Sports
    Murrays red, green and blue tell tails. Sail trimming guides.
    MURRAYS TELL TAIL SET
    Murrays Sports
    Ronstan Single Block, Ferrule Murrays Part# 21-0469 This is the original clew block on most of the old Hobie cat Sailboats. This will work as a replacement jib clew block for Hobie® 14, 16 and 18 cats. Lightweight stainless block with ferrule has 1-1/8" x 5/8" sheave diameter, Delrin bearing and 1/2" line capacity. SWL: 950 lbs. This is a great option if you're looking to use a larger line diameter on your sheets or want the classic look.
    RONSTAN SINGLE BLOCK, FERRULE
    Ronstan
    S HOOK WAVE MAIN SHEET
    Hobie
    MYLAR SAIL REPAIR 2"x10' CLEAR
    Misc
    Murrays 57mm Carbo 6:1 Mainsheet System Murrays Part# 28-61 The Murrays Harken 57mm Carbo 6:1 Mainsheet System is an improved low profile mainsheet system for Hobie 16.  By attaching a fairlead to the back side of the cleat mount the Murrays system does not need a becket on the lower block which makes the system more compact and gives sailors the ability to sheet in farther and or rake the mast back farther before having the mainsheet bottom out and go block to block.
    MURRAYS 57MM CARBO 6:1 MAINSHEET SYSTEM
    Harken
    Harken 29mm Bullet Block Murrays Part# 28-0082 Medium-size Harken single bullet block with Delrin® ball bearings works well for control line or jib sheeting lines. The low-friction bullet block is compact and lightweight, with fast trim and release under high or low loads.
    HARKEN 29MM BULLET BLOCK
    Harken
    Clew Kit 5-Hole (H16 Jib) Murrays Part# 001-1012 Clew kit for Hobie® 16 jib includes one pair of anodized aluminum plates with rivets to be set with a hammer. Each plate has five holes and measures 8" maximum length by 1-1/2" wide. Replacement rivets are available separately (#19-5006). This product replaces discontinued item #50-22240000.
    CLEW KIT 5-HOLE (H-16 JIB)
    Murrays Sports
    H-16 JIB BATTEN 44" 44" Murrays jib batten with a trentec batten cap.   Batten #3 in a Hobie jib batten set - 20400001 It is also use for the batten #8 on a Hobie 16 main sail batten set - 21000001
    H-16 JIB FIBERGLASS BATTEN 44"
    Murrays Sports
    Downhaul Kit 3:1 Wave Murrays Part# 001-2029 This is a HCA and Formula Wave Class Legal downhaul kit. The Hobie Wave is a simple boat, and this simple kit helps make downhaul adjustments quick and easy. Installs in minutes with a Philips head screw driver. This can also be an intermediate downhaul kit for the H16 for recreational use, it's not class legal for HCA racing.
    Downhaul Kit 3:1 Wave Murrays Part# 001-2029 This is a HCA and Formula Wave Class Legal downhaul kit. The Hobie Wave is a simple boat, and this simple kit helps make downhaul adjustments quick and easy. Installs in minutes with a Philips head screw driver. This can also be an intermediate downhaul kit for the H16 for recreational use, it's not class legal for HCA racing.
    DOWNHAUL KIT 3:1 WAVE
    Murrays Sports
    Batten Cap Jib Leech H16 Murrays Part# 50-2133000 Hobie® factory jib leech batten cap for Hobie® 16. For batten tie, use 18" of 1/8" Dacron® solid braid #39-0221. These are also used on the top two battens of a Hobie Wave and the top batten of a Hobie 18 Mainsail. Sold individually
    H-16 JIB BATTEN LEECH CAP (EA)
    Hobie
    The Murrays Prindle 16 main halyard is made to factory specs.  We use 316 stainless steal bare wire and thimbles.  It also has a Ronstan Halyard Shackle with a captive pin so that it will not fall out when loosened. Prindle part number 9026
    P-16 MAIN HALYARD WITH SHACKLE
    Murrays Sports
    PRINDLE JIB HALYARD W/CLIPS
    Murrays Sports
    Headboard Replacement Kit Murrays Part# 001-1014 Headboard Replacement Kit includes one pair of anodized aluminum plates with rivets to be set with a hammer. Plates measure 5" high x 4" wide x 6-1/4 diagonal. Replacement rivets are available separately (#19-5006).
    HEADBOARD REPL KIT
    Murrays Sports
    HOBIE 14 MAIN HALYARD COMPTIP This main halyard is used to raise the main sail on a Hobie® 14 with CompTip on its mast. Constructed to factory specifications. Compare to Hobie Cat® #10657001.
    H-14 MAIN HALYARD COMPTIP
    Murrays Sports
    Batten Cap Leech H14/16/17/18 Main E Murrays Part# 012-3003-1 No more knots at the trailing edge. Adjust sail shape in seconds without tying and untying knots. Release tension to prolong sail shape and life. Individual batten cap for Hobie 14, 16, 17 or 18 main sail. Mainsail batten cap for Saturn shape main sail battens used on Hobie, Prindle some Nacra sails. Trentec part number BC-HM Compare to Hobie 11323000 Sold individually 
    H/14/16/17/18 MAIN BATTEN LEECH CAP
    Tren-Tec
    Rivet Solid A 4-6 (1/8 X 3/8) Murrays Part# 19-5005 Solid aluminum 1/8" x 3/8" rivet is designed to be set with a hammer.
    RIVET SOLID A 4-6 (1/8x3/8")
    Misc
    Out of Stock
    SAIL JIB Hobie 16 WHITE
    Hobie