Sailing Hardware

217 products

    217 products
    Out of Stock
    3/16 - 1/4" Split Ring Murrays Part# 22-9492 Stainless steel split ring (ring ding) for 3/16″-1/4″ diameter clevis pin. This is the standard size Hobie split ring used all over the boats, most commonly on the shrouds, forestay and roller furler Medium Split ring Dimensions: 5/8″ Diameter Material: 316 Stainless steel. This is the most common size Split ring on Hobie, Nacra and Prindle Catamarans. 20860000 Medium Clevis Ring.
    SPLIT RING 3/16-1/4"
    Misc
    10 Hole Hobie shroud adjuster
    SHROUD STAY ADJUSTER 10-HOLE
    MISC
    3/16 - 1/4" Split Ring with Pigtail Murrays Part# 22-9491 A pigtail makes this split ring (ring ding) easier to open than standard split rings. For use on 3/16″ – 1/4″ clevis pins Material: 316 Stainless steel. Medium Split ring Dimensions: 5/8″ Diameter This is the most common size Split ring on Hobie, Nacra and Prindle Catamarans. Applications: All Hobies Shroud and Forestay split ring H18/ Hobie 18 SX – Tiller Yoke Clevis Pin Ring Also called Ring Ding, Clevis Ring, Cotter Ring or Ringy Ding
    SPLIT RING 3/16-1/4" PIGTAIL
    Misc
    Kit for Hobie® 14 or 16 includes 16 pieces: mast hinge pin, clevis pin assortment and split ring assortment. Compare to Hobie Cat® #30303.
    PINS & RINGS KIT: H-14/16
    Murrays Sports
    Cotter Pin 3/32 X 3/4 Murrays Part# 19-1015 Cotter pins are used on all Hobie, Nacra and Prindle rudder pins. They are used to secure the rudder pins. Compare to Hobie Cat® #8060111. Stainless steel cotter pin measures 3/32" x 3/4".
    COTTER PIN 3/32 X 3/4" SS
    Misc
    RIVET CCP 6-6 (3/16 X 3/8) Murrays Part# 19-5032 Stainless steel 3/16" x 3/8" pan head rivet Among other uses, the Stainless steel 3/16" x 3/8" pan head rivet can be used when Hobie® rivet #8010131 is specified: Hobie 14 (2) or 16 (4) mast head Hobie Wave/Getaway/14/16/17/18/18SX/ mast base (4) Hobie 14/16 rudder upper casting (2) Hobie 14/16 tiller end cap (2) Hobie 14/16 boom front end cap (3) Pair with stainless steal rivet casings to seal the holes when using on the mast.
    RIVET CCP 6-6 (3/16 X 3/8)
    Misc
    Murrays PN 001-0053 The Murrays Rudder Stiffening Spacer is a 2" diameter spacer for use on Hobie, Nacra and Prindle catamarans to eliminate excessive clearances between rudders and castings which cause rudder slop, side to side wobble, and thwart rudder alignment. A kit with spacers and nuts is also available (#01-2053).  The Murrays Rudder Stiffening Spacer are quite thin so that you can achieve a perfect fit. Standard kits come with 8 spacers.
    SPACER: RUDDER STIFFENING
    Murrays Sports
    CLEVIS PIN 3/16 X 7/8
    Misc
    Carbine Hook (Plastic) A quick connection of trapeze shock cord to height control adjustment. 2-1/4" long. Compare to Hobie Cat® #2101.
    CARBINE HOOK (PLASTIC)
    Murrays Sports
    Hobie 18 clevis pin kit includes 13 pieces: mast hinge pin, clevis pin assortment, and split ring assortment. Compare to Hobie Part Number #30304 Murrays.com
    PINS & RINGS KIT: H-18
    Murrays Sports
    Nut Nylock 5/16-18 Stainless Steel Murrays Part# 19-2520 5/16-18 nylock nut is used on Hobie® rudders. The stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Compare to Hobie Cat® item #8050311 and 8050321 shroud anchor pin nut Used with Hobie Getaway Bow Tang Bolt
    NUT NYLOCK 5/16-18 (SS)
    Misc
    Rudder Cam Screws H17, H18, H20, Older Wave and Getaway Murrays Part# 001-3551 The Murrays Rudder Cam Pins are a pair of sister screws for use on the Hobie 17, 18, 20, 21, as well as the older Hobie Wave and Getaway rudder cams. These pins are an upgrade form the original stock hollow flare rivet that came on the Hobie. The Sister Screws are much easier to install and remove, and they are reusable. Compare to Hobie Cat® #5203 and #50312301. Sold in pairs
    RUDDER CAM PINS ONLY H17/18/20
    Murrays Sports
    Shackle Pin Only 3/16 Threaded Murrays Part# 21-0032 Threaded stainless pin fits 3/16" Ronstan D or bow shackle.
    SHACKLE PIN ONLY 3/16 THREADED
    Ronstan
    STAINLESS STEEL CINCH RINGS 3/16 - 3/8" Stainless steel cinch ring for use securing the ends on shock cord or line. Also called hog rings. We use these to secure the hook on the end of trapeze bungees, as securing the ends on our shock cord trampoline lacing kit. Sold Individually. Hobie part 53180010
    STAINLESS STEEL CINCH RINGS 3/16 - 3/8"
    Misc
    5/16 - 3/8" Split Ring Stainless steel split ring for 5/16″-3/8″ diameter clevis pins. The larger size makes it easier to get on and off. Large Split ring Dimensions: 3/4″ Diameter Material: 316 Stainless steel. Also called Ring Ding or Ringy Dingy. Hobie Part number 20860010 – RF686
    SPLIT RING 5/16 -3/8"
    Misc
    Screw RHMS 5/16-18 X 1.25" Stainless Steel Murrays Part# 19-3530 Stainless steel round head machine screw measures 5/16-18 x 1-1/4". Bow Tang Bolt Equivalent to Hobie Cat® Part# 8030301
    SCREW RHMS 5/16-18 X 1.25 (SS)
    Misc
    clevis pins with split rings for the standing rig and mast stepping systems of Hobie 17, Hobie 20, or Nacra. Kit includes 18 pieces: mast hinge pin, clevis pin assortment, and split ring assortment.  Compare to Hobie Cat #30317.
    PINS & RINGS KIT:H-17/20/NACRA
    Murrays Sports
    3/16" Split Ring - 7/16″ Diameter Murrays Part# 22-9490 Stainless steel split ring for 1/8-3/16″ diameter clevis pins. Comparable to Hobie Cat® #81503100 Small Clevis Ring. This is a super small size, best for locations where you may be concerned about it snagging on something. The small size helps prevent it from snagging on lines, sheets, sails and clothing.
    SPLIT RING 3/16
    Misc
    Eyestrap Wave Bridle Murrays Part# 50-38120011 ​Hobie® factory replacement eyestrap for Hobie Wave bridle.
    EYESTRAP WAVE BRIDLE
    Hobie
    M8 T-Nuts: Titanium Hydrofoil Mast Track Inserts
    TITANIUM T-NUTS M8
    MISC
    CLEVIS PIN 3/16 X 5/8
    Misc
    M8x30mm TITANIUM TORX BOLT
    Murrays Sports
    SPRING CLIP: 1/4 - 5/16
    Misc
    Stainless steel cinch ring is also known as a hog ring. Use shock cord seizing pliers for a smooth installation; standard pliers can give a suitable cinch.
    CINCH RING 1/4" 6mm (X-0)
    Misc
    Titanium Hydrofoil Track Lock Universal Track Nut Murrays part# 55-0030T The Only Titanium Universal Track Nut! These track nuts lock into position with a set screw, setting them apart from other track nuts on the market. They were designed to be used with any foil board track and are made from 100% GR5 Titanium so corrosion will never be an issue. They are designed to work with any foil system whether it uses m6 or m8 hardware. The Track Lock Universal track Nut comes with both M6 and M8 threaded screw
    TITANIUM HYDROFOIL TRACK LOCK UNIVERSAL TRACK NUT (4)
    Misc
    M6 x 25mm Titanium Hydrofoil Screws Murrays Part# 55-0025T The M6 x 25mm Titanium Hydrofoil Screws are stronger and more corrosion resistant than stainless steal foil hardware. Compatible with all M6 foil track inserts. The 25mm length is used for both board to foil connection as well as foil assembly. Commonly used with F-One, Naish, Airush, Takuma, Axis, Sab foil, Armstrong and more. Titanium foil hardware does not require greasing or regular checking. Titanium does not corrode or seize
    M6 x 25mm Titanium Hydrofoil Screws Murrays Part# 55-0025T The M6 x 25mm Titanium Hydrofoil Screws are stronger and more corrosion resistant than stainless steal foil hardware. Compatible with all M6 foil track inserts. The 25mm length is used for both board to foil connection as well as foil assembly. Commonly used with F-One, Naish, Airush, Takuma, Axis, Sab foil, Armstrong and more. Titanium foil hardware does not require greasing or regular checking. Titanium does not corrode or seize
    M6x25mm TI TORX COUNTER SUNK BOLT
    Murrays Sports
    Shackle Pin Only 1/4 Threaded Murrays Part# 21-0033 Threaded stainless pin fits 1/4" Ronstan D or bow shackle.
    SHACKLE PIN ONLY 1/4 THREADED
    Ronstan
    Bolt Hex Head 5/16-18 X 2.50" Stainless Steel Murrays Part# 19-2231 Stainless steel rudder bolt for all Hobie® Cats measures 5/16-18 x 2.50".  Used on Hobie Getaway Bow Spreader - Bow Tang Bolt. Rudder bolt for both the upper and lower rudder casting. Compare to Hobie Cat® Part# 8040341
    BOLT HEX HEAD 5/16-18 X 2.50" SS
    Misc
    Prindle split rings and clevis pin kit, mast hinge pin
    PINS & RINGS KIT: PRINDLE
    Murrays Sports
    Hobie 3062 1/4" Bow shackle with quick release pin
    QR BOW SHACKLE 1/4"
    Murrays Sports
    1/2 BALL (NYLON) - Hobie half round washer spacer tiller connector - Hobie part number 11510000 HOBIE HALF SPHERE TILLER CONNECTOR
    1/2 BALL (NYLON)
    Murrays Sports
    Screw RHMS 1/4-20 X 1/2" Stainless Steel Murrays Part# 19-3019 Stainless steel, Phillips pan head 1/4-20 x 1/2" machine screw is used to fasten mast bearing on post-1990 Hobie® 18. Compare to Hobie Cat® #8032011
    SCREW RHMS 1/4-20 X 1/2" (SS)
    Misc
    CINCH RING 3/8 10mm (X-2) EACH Stainless steal cinch ring for use on 3/8" shock cord or line. Sold Individually. Hobie part 53180010
    CINCH RING 3/8 10mm (X-2) EACH
    Misc
    Rivet 6-18 Aluminum RIVET POP 3/16 x 1 1/8th inch aluminum rivet to hold the traveler control sheave on a H16 front crossbar from late 90s to current. Hobie Part Number 8011251
    Rivet 6-18 Aluminum
    MISC
    M6 x 25mm Stainless Steel Torx Head Screw The M6 x 25mm Stainless Steel Torx Head Screw is a very common size hydrofoil mounting screw. Compatible with all M6 foil track inserts and standard on F-One Rocket Wing Boards and Naish Hover Boards. Also used in foil assembly on F-One Carbon and FCT foils. Sold in a package of 4 
    M6 STAINLESS STEEL TORX HEAD SCREW (4)
    F-One
    Screw 1/4-20 x 5/8 PHMS-P Stainless Steel Murrays Part# 50-8030331 This screw is used on the Hobie wave to secure the eye straps to the inner edge of the crossbars for connecting the tramp pulleys on the classic wave or "other" on the club version.
    SCREW 1/4-20 x 5/8 PHMS-P SS
    Misc
    Out of Stock
    Nacra Boom Pin
    NACRA
    Titanium M6 T-Nut
    M6 T-NUTS: TITANIUM HYDROFOIL MAST TRACK INSERTS
    Wing Foiling
    RING: 3/8 X 2 ID (NYLON)
    Misc
    FAST EYE SNAP Brass 2-1/8"
    Misc