MISC

337 products

    337 products
    Universal Drain Plug for most Hobie, Nacra and Prindle Catamarans which includes a gasket and fits most Hobie, Nacra and Prindle catamarans. Hobie part number 10091000
    Hobie drain plug 10091000 Hobie 18
    DRAIN PLUG WITH GASKET
    Misc
    3/16 - 1/4" Split Ring Murrays Part# 22-9492 Stainless steel split ring (ring ding) for 3/16″-1/4″ diameter clevis pin. This is the standard size Hobie split ring used all over the boats, most commonly on the shrouds, forestay and roller furler Medium Split ring Dimensions: 5/8″ Diameter Material: 316 Stainless steel. This is the most common size Split ring on Hobie, Nacra and Prindle Catamarans. 20860000 Medium Clevis Ring.
    SPLIT RING 3/16-1/4"
    Misc
    10 Hole Hobie shroud adjuster
    SHROUD STAY ADJUSTER 10-HOLE
    Misc
    3/16 - 1/4" Split Ring with Pigtail Murrays Part# 22-9491 A pigtail makes this split ring (ring ding) easier to open than standard split rings. For use on 3/16″ – 1/4″ clevis pins Material: 316 Stainless steel. Medium Split ring Dimensions: 5/8″ Diameter This is the most common size Split ring on Hobie, Nacra and Prindle Catamarans. Applications: All Hobies Shroud and Forestay split ring H18/ Hobie 18 SX – Tiller Yoke Clevis Pin Ring Also called Ring Ding, Clevis Ring, Cotter Ring or Ringy Ding
    SPLIT RING 3/16-1/4" PIGTAIL
    Misc
    Cotter Pin 3/32 X 3/4 Murrays Part# 19-1015 Cotter pins are used on all Hobie, Nacra and Prindle rudder pins. They are used to secure the rudder pins. Compare to Hobie Cat® #8060111. Stainless steel cotter pin measures 3/32" x 3/4".
    COTTER PIN 3/32 X 3/4" SS
    Misc
    Stainless steel clevis pin. Measurement is 1/4" diameter x 5/8" grip length. Hobie part number 8020361, 8020381 and 8020380.
    CLEVIS PIN 1/4 X 5/8
    Misc
    Sealed Stainless Steel 3/16" x 3/8" Pan Head Rivet Murrays Part# 19-5032S Sealed rivets have a sealed end that does not require rivet casings to make them water tight. One and done, no casing needed, just insert and pop as you would a normal rivet, and your hole will be sealed. Among other uses, the Stainless steel 3/16" x 3/8" pan head rivet can be used when Hobie® rivet #8010131 is specified: Hobie 14 (2) or 16 (4) mast head Hobie Wave/Getaway/14/16/17/18/18SX/ mast base (4) Hobie 14/16
    RIVET CCP SEALED 6-6 (3/16 X 3/8)
    Misc
    CLEVIS PIN 3/16 X 7/8
    Misc
    Nut Nylock 5/16-18 Stainless Steel Murrays Part# 19-2520 5/16-18 nylock nut is used on Hobie® rudders. The stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Compare to Hobie Cat® item #8050311 and 8050321 shroud anchor pin nut Used with Hobie Getaway Bow Tang Bolt
    NUT NYLOCK 5/16-18 (SS)
    Misc
    Hobie Cat 8010181 Rivet
    RIVET CCP SEALED 6-4 (3/16 X 1/4)
    Misc
    Quick Release Pin Deluxe  3/16 X 3/4" Murrays Part# 18-3M075 This Quick Release Pin features 2 locking balls for a extra secure grip, and a push button deluxe dished head with a hole for lanyard attachment. The Deluxe pin is quick and easy to remove and install, and makes getting on and off the water quicker and easier.
    QUICK RELEASE PIN DELUXE 3/16 X 3/4"
    Misc
    STOP SLEEVE 1/8"
    Misc
    Use this 1/8″ Dacron line for batten tie line and roller furling systems. For batten ties, allow about 18″ of line for each batten. Sold per foot. Spool: 1000′ (304.9m). Compare to Hobie part number RH112WHT - 8004510
    DACRON SOLID BRAID 1/8" WHITE
    Misc
    Rivet CCC 6-6 (3/16 X 3/8) Countersunk Murrays Part# 19-5024 Countersunk stainless steel 3/16" x 3/8" rivet for traveler tracks, etc. Compare to Hobie Part # 8010201. This rivets is what Hobie recommends for both the main traveler tack and the jib traveler track. We also recommend using an 1/8" stop sleeve, part number 002-1041, as a spacer to help you apply pressure on the rivet inside the track, as the track is too narrow for most rivet guns to get far enough inside to apply pressure to the rivet.
    RIVET CCC 6-6 CSK
    Misc
    Clevis Pin 1/4 X 1/2 Murrays Part# 22-9808 Stainless steel clevis pin. Measurement is 1/4" diameter x 1/2" grip length (shoulder to the split ring hole). Substitute for Hobie Cat® #8020371.
    CLEVIS PIN 1/4 X 1/2
    Misc
    3/16" Split Ring - 7/16″ Diameter Murrays Part# 22-9490 Stainless steel split ring for 1/8-3/16″ diameter clevis pins. Comparable to Hobie Cat® #81503100 Small Clevis Ring. This is a super small size, best for locations where you may be concerned about it snagging on something. The small size helps prevent it from snagging on lines, sheets, sails and clothing.
    SPLIT RING 3/16
    Misc
    5/16 - 3/8" Split Ring Stainless steel split ring for 5/16″-3/8″ diameter clevis pins. The larger size makes it easier to get on and off. Large Split ring Dimensions: 3/4″ Diameter Material: 316 Stainless steel. Also called Ring Ding or Ringy Dingy. Hobie Part number 20860010 – RF686
    SPLIT RING 5/16 -3/8"
    Misc
    Screw RHMS 5/16-18 X 1.25" Stainless Steel Murrays Part# 19-3530 Stainless steel round head machine screw measures 5/16-18 x 1-1/4". Bow Tang Bolt Equivalent to Hobie Cat® Part# 8030301
    SCREW RHMS 5/16-18 X 1.25 (SS)
    Misc
    Rivet CCP 6-8 (3/16 X 1/2) Murrays Part# 19-5033 Stainless steel 3/16" x 1/2" rounded pan head rivet. Compare to Hobie Cat® #8011231.
    RIVET CCP 6-8 (3/16 X 1/2)
    Misc
    Rivet CCP 6-4 (3/16 X 1/4) Murrays Part# 19-5031 Stainless steel 3/16" x 1/4" rounded pan head rivet. Compare to Hobie Cat® #8010181. This is a common rivet used on many extrusions. Hobie, Nacra, Prindle masts and booms. Pair with a rivet casing to seal the rivet hole when used on masts. All Hobie mast hounds, tangs, heads, and cheek blocks. Used with Hobie Getaway Bow Spreader Plates Used on Hobie Getaway FWD and REAR Crossbar Stop Plates
    RIVET CCP 6-4 (3/16 X 1/4)
    Misc
    CLEVIS PIN 3/16 X 1/2
    Misc
    STAINLESS STEEL CINCH RINGS 3/16 - 3/8" Stainless steel cinch ring for use securing the ends on shock cord or line. Also called hog rings. We use these to secure the hook on the end of trapeze bungees, as securing the ends on our shock cord trampoline lacing kit. Sold Individually. Hobie part 53180010
    STAINLESS STEEL CINCH RINGS 3/16 - 3/8"
    Misc
    Premium Marine shock cord Use 3/16″ or 1/4″ for trapeze shock cords. Hobie uses #RS014BLK for 1/4″ bungee cord. Uses: 1/4″ shock cord is primarily used for trapeze shock cord.   Hobie 16 use 2 x 8′ sections for the trapeze shock cord Hobie 17 uses one 12′ section for the trap shock cord. Hobie 18 uses 4 x 7' pieces Nacra rudder bungees: Factory spec is 4′ of 1/4″ shock cord but it is a common upgrade to use 5/16″ We use 60' of 3/8' in our trampoline bungee lacing kits.
    PREMIUM MARINE GRADE SHOCK CORD
    Misc
    Book: Catamaran Racing for the 90's Murrays Part# 45-0052 It may be the 2000's, but this book is still relevant to today's cat sailor. Improve your sailing in any or all of the 21 major subjects covered in this manual.
    BOOT: CATAMARAN RACING FOR THE 90'S
    Misc
    Rivet CCP 6-10 (3/16 X 5/8) Murrays Part# 19-5034 Stainless steel 3/16" x 5/8" rounded pan head rivet. Compare to Hobie Cat® #8010121. Halyard mast cleat rivet
    RIVET CCP 6-10 (3/16 X 5/8)
    Misc
    Quick-Release Pin Detent 1/4 X 1-1/2 Murrays Part# 18-4D150 The Quick-Release Pin Detent 1/4 X 1-1/2 is an economical, quick connection for Hobie 16 mast step pin. A spring-loaded ball exerts sufficient pressure to help avoid accidental release. Measurements are 1/4″ diameter x 1-1/2″ maximum grip length (distance from the shoulder to the locking ball bearings).
    QUICK RELEASE DETENT PIN 1/4 X 1.5
    Misc
    M8 T-Nuts: Titanium Hydrofoil Mast Track Inserts
    TITANIUM T-NUTS M8
    Misc
    Quick Release Detent Pin 1/4 X 3" Murrays Part# 18-4D300 Economical quick release pin has a spring-loaded ball that exerts sufficient pressure to help avoid accidental release. Measurements are 1/4" diameter x 3" maximum grip length (distance from the shoulder to the locking ball bearings). Uses: - Use as mast step pin on Hobie® 21 and Prindle 16/18/18-2/19 cats. Compare to Hobie part # 8020501
    Quick Release Detent Pin 1/4 X 3" Murrays Part# 18-4D300 Economical quick release pin has a spring-loaded ball that exerts sufficient pressure to help avoid accidental release. Measurements are 1/4" diameter x 3" maximum grip length (distance from the shoulder to the locking ball bearings). Uses: - Use as mast step pin on Hobie® 21 and Prindle 16/18/18-2/19 cats. Compare to Hobie part # 8020501
    QUICK RELEASE DETENT PIN 1/4 X 3"
    Misc
    Hobie 18 mast step hinge pin, has a hole on one end only. The headless clevis pin measures 1/4″ diameter by 3-3/8″ grip length Hobie Part # 8020501
    CLEVIS PIN HEADLESS 1/4 X 3-3/8
    Misc
    CLEVIS PIN 3/16 X 5/8
    Misc
    Cat Bag 4" Murrays Part# 001-1169 The Cat Bag provides handy storage inside a deck port! The sturdy nylon bag with plastic collars hangs inside 4" access port on a molded shoulder. 12" deep. Hobie Cat® uses #5402 for this item.
    4" PORT CAT BAG
    Misc
    Quick-Release Pin Deluxe 1/4 X 3/4 Murrays Part# 18-4M075 This economical pin features a spring-loaded ball that exerts sufficient pressure to help avoid accidental release. The pin is also available with a lanyard to help prevent loss of pin (see related items below). Measurements are 1/4" diameter x 3/4" maximum grip length (distance from the shoulder to the locking ball bearings). Compare to Hobie Cat® #20302.
    QUICK RELEASE DELUXE PIN 1/4 X 3/4
    Misc
    Sealed Rivet CCP 6-8 (3/16 X 1/2) Murrays Part# 19-5033S Sealed rivets have a sealed end that does not require rivet casings to make them water tight. One and done, no casing needed, just insert and pop as you would a normal rivet, and your hole will be sealed. Sealed Stainless steel 3/16" x 1/2" rounded pan head rivet. Compare to Hobie Cat® #8011231 Rivet and Hobie Cat® #8011291 rivet casing.
    RIVET CCP SEALED 6-8 (3/16 X 1/2)
    Misc
    O-Ring: 4" Screw-In Port Murrays Part# 001-1161OR This is an approximate O-Ring for Viking Marine 4" ports.
    O-RING: 4" SCREW-IN PORT
    Misc
    Port Cat Bag 5" Murrays Part# 001-1178 The Cat Bag provides handy storage inside a deck port! Designed to hang inside 5" access port (#01-4210 or #01-4210BK) on a molded shoulder. Details: 12" deep Comes in one color: red Metal collar - gap in ring for easy installation Cinch bag style
    5" PORT CAT BAG
    Misc
    Bolt Hex Head 5/16-18 X 2.50" Stainless Steel Murrays Part# 19-2231 Stainless steel rudder bolt for all Hobie® Cats measures 5/16-18 x 2.50".  Used on Hobie Getaway Bow Spreader - Bow Tang Bolt. Rudder bolt for both the upper and lower rudder casting. Compare to Hobie Cat® Part# 8040341
    BOLT HEX HEAD 5/16-18 X 2.50" SS
    Misc
    A Multi-Sport / Water / Reef Helmet Hat. Purposely designed for Indo Surfing, Kitesurf, kiteboarding, Windsurf, Sailing, Kayaking & Wingboarding. It has a Hard protective shell for light / medium impacts. Non-water absorbent Foam with Water Proof Lining built for Flex Comfortability
    SURF AND FOIL IMPACT HAT
    Misc
    Titanium Hydrofoil Track Lock Universal Track Nut Murrays part# 55-0030T The Only Titanium Universal Track Nut! These track nuts lock into position with a set screw, setting them apart from other track nuts on the market. They were designed to be used with any foil board track and are made from 100% GR5 Titanium so corrosion will never be an issue. They are designed to work with any foil system whether it uses m6 or m8 hardware. The Track Lock Universal track Nut comes with both M6 and M8 threaded screw
    TITANIUM HYDROFOIL TRACK LOCK UNIVERSAL TRACK NUT (4)
    Misc
    DIAMOND WIRE ROLLER
    Misc
    CINCH RING 3/8 10mm (X-2) EACH Stainless steal cinch ring for use on 3/8" shock cord or line. Sold Individually. Hobie part 53180010
    CINCH RING 3/8 10mm (X-2) EACH
    Misc