All Sailing Parts

All Sailing Parts

2266 products

Everything Nacra, Prindle, Hobie and a few more fun odds and ends.

2266 products

Sort

Forward WIP Sailing Glove

The Forward WIP Sailing Glove has been professionally designed for sailing and windsurfing. They provide the user a snug fit, maximum protection, improved dexterity, comfort and excellent durability. This model has reinforced panels on the back of the hand to protect from impacts during sailing maneuvers.

Features:

Excellent durability
Snug fit
Improved dexterity
Water Shedding - holds less water
Seamless wrap around Amara® reinforcement on fingers combatting c

FORWARD WIP SAILING GLOVE

Harken 27mm Micro Eyestrap

Murrays Part# 28-0281

Eyestraps are useful accessories. They form light-duty mounting bases for blocks, serve as lash-down points, and can be used for fairleads.

Eyestrap for Cam-Matic 338, 423, 468, 471

Stainless steel eyestrap mounts on Harken aluminum Micro Cam-Matic (#28-0338) or Micro Carbo-Cam (#28-0423).

HARKEN 27MM MICRO EYESTRAP

Mini Fairlead: 1 X 1/4
Murrays Part# 25-0338
Stainless mini fairlead strap measurements:
A = 1 1/8" between holes center-to-center
B = 3/8" height
C = 3/16" hole diameter
Compare to Hobie Part 11470000
Rear Crossbar Padeye

RONSTAN MINI FAIRLEAD: 1 X 1/4

Mylar Sail Repair Tape 2x10"- Clear

Murrays Part# 010-3410

Make quick and easy sail repairs with Bainbridge's 10' roll of 2"-wide clear mylar polyester film with pressure-sensitive adhesive.

MYLAR 2x10" SAIL REPAIR TAPE-CLEAR

Cat Trax Washer & Cotter Pin Kit

Murrays Part# 13-1401-7

Kit includes: Replacement washers and cotter pins for two Cat Trax beach wheels.

CAT TRAX WASHER & COTTER PIN KIT

CAT TRAX WIDE HULL CRADLES

Quick Release Pin Detent 1/4 X 1"

Murrays Part# 18-4D100

This quick pin has a spring-loaded ball that exerts sufficient pressure to help avoid accidental release. Measures 1/4" diameter x 1" long.

Can be used to replace 1/4" clevis pins up to 1" long.  Not recommended for use in shroud adjusters or chain plates.

QUICK RELEASE PIN DETENT 1/4 X 1"

Deluxe Quick Release Pin 1/4 X 1 with Lanyard

Murrays Part# 18-4M100

This quick release pin features a push button on the top that releases 2 spring-loaded balls at the tip that secure the pin in place. Uses:

Hobie boom Gooseneck quick connection pin on the 14, 16 and 18.
Hobie 18 main clew to outhaul car connection pin.

Compare to Hobie Cat #20305 PIN, QR 1/4 X 1 CUP

Upgrade for Hobie 8020410 and 8020411 clevis pin

DELUXE QUICK RELEASE PIN 1/4 X 1" WITH LANYARD

Replaceable Aluminum Trap Handle

Murrays Part# 007-2010

Foam-covered aluminum handle is easily installed onto existing trapeze wire. Carry a spare as a temporary repair, then replace the wire at your convenience. Each.

Hobie Cat® Part# 2010

REPLACABLE ALUMINUM TRAP HANDLE

O-Ring: 4" Screw-In Port

Murrays Part# 001-1161OR

This is an approximate O-Ring for Viking Marine 4" ports.

O-RING: 4" SCREW-IN PORT

Harken 8mm Bow Shackle

Murrays Part# 28-2117

The Harken 8mm Bow Shackle is a forged stainless steel shackle that is polished to a high luster and stamped with the screw pin diameter. Bow shackles are best for multidirectional loads. Their large interior opening allows plenty of articulation especially when attached to a round bail.

HARKEN 8MM BOW SHACKLE

Hobie 18 main sheet traveler car assembly - Hobie part number 61800001 - Murrays.com

Traveler Car Assembly H18 Complete - 61800001 - Murrays.com

H-18 TRAVELER CAR ASSEMBLY

Tiller Crossbar Adjustable Cap Kit

Murrays Part# 50-60400011M

Murrays Tiller Crossbar Adjustable Cap Kit installs in the end of the Hobie tiller crossbar and allows you to adjust the width of the crossbar which controls the angel of the rudders.

Hobie discontinued this part and this is a Murrays Replacement part that we have made here in California.

Applications: H14, H16, H17, H18, Hobie 18 SX tiller x-bar

Tiller Crossbar Adjuster: 1

HOBIE TILLER CROSSBAR ADJUSTABLE END CAP - 60400011

Roller Furler Drum Ball Bearing
Murrays Part# 50-61670000
Hobie® factory replacement bearing for Hobie roller furler. A total of 18 ball bearings are required per furler.

HOBIE ROLLER FURLER BEARING

Prindle 15/16/18 Owner Manual

Murrays Part# 56-9050

This is a copy of the original factory owner's manual for Prindle 15, 16 and 18 catamarans built by Performance Sports.

PRINDLE 15/16/18 OWNER MANUAL

Nylon Washer Internal Casting Prindle
Murrays Part# 56-F118
Nylon washer is used on Prindle rudder casting to separate the upper sheaves to help keep the line from fouling. Order four per side to remove as much slop as possible.
Performance Sports factory item #F118

PRINDLE NYLON WASHER INTERNAL CASTING

Hobie Gooseneck Hinge Vertex

Murrays Part# 50-50772031
Hobie® factory replacement gooseneck vertex for all Hobie® Cats.

Hobie Part# 50772031

HOBIE GOOSENECK HINGE VERTEX

Boom Outhaul Bearing H18
Murrays Part# 50-60240000
Boom bearing for Hobie 18 outhaul system

H-18 BOOM OUTHAUL BEARING

RONSTAN 4" HORN CLEAT

SK78 Mini Spool 3mm Dyneema Lashing Line

The SK78 Mini Spool 3mm- Robline Dyneema good for any small boat kit…. for tying. lashing, lanyards, pigtails etc. Easily spliced with a small Selma Fid or a D Splicing tool.

Honeywell International produces a similar line, marketed as Spectra®

Identical to Ocean 3000 XG, but on a smaller spool, this rope is made of pure Dyneema SK78 and treated with FSE Robline’s S.Y.I.S. coating technology.
Dyneema SK78 has the same high strength of SK75, but with lower creep

SK78 MINI DYNEEMA SPOOL 3MM

Nacra Tiller Tie Bar End Tendon Assembly

Murrays Part# 56-31567-2

The rubber tiller tiebar connection including string.
This part connects the tillerarm with the tiller crossbar.

NACRA TILLER TIE BAR END TENDON ASSEMBLY

O’Pen Skiff Tiller End Plug
Murrays Upgrade

Murrays Part# 65-316970

The O’Pen Skiff Tiller End Plug Murrays Upgrade is the solution to a weak point on the O’Pen Skiff boat. This upgrade replaces the two standard tiller end plugs that go on each pintle. Only two are required instead of four because the Murrays Tiller end plug is solid and spans the whole distance inside the rudder housing. So you don't need two per pintle only per rudder.

O'PEN SKIFF TILLER END PLUG (MURRAYS UPGRADE)

Nylon Port Fastener Kit

The Port Nylon Fastener Kit includes all the necessary nylon fasteners (screws, washers and nuts) plus marine silicone sealant for the installation of two access ports, also known as hatches, on to a catamaran like a Hobie, Nacra or Prindle.

Use this page to order:
001-1159 White
001-1160 Black

NYLON PORT FASTENER KIT

Hobie Main Sail Headboard w/ rivets
Replacement Hobie factory Hobie Main Sail Headboard w/ rivets. Hobie part #68330011

ALUMINUM HEADBOARD WITH RIVETS

Overhead Surf-Cap-Safety Retainer

Murrays Part# 54-4413

The Hat Leash is finally here!  New from Overhead Surf is the Cap-Safe Retainer lanyard. Simply attached to your hat or cap and ensures that if it does get blown off your head, it stays with you.  Total hat saver!!  Now featuring a breakaway snap on the leash so it wont try to rip your head off if the hat gets caught on something.

Features:

Break away snap connection
Hook/Loop for hat connection

SURF HAT SAFETY RETAINER

SMALL BLOCK W/REMOVABLE SHEAVE

This small block is used on trapeze adjustment systems where the removable sheave enables installation without cutting wires.

Specifications: 1-3/16" removable sheave, Teflon® bearing and 5/16" line capacity.

Hobie item #3103

SMALL BLOCK W/REMOVABLE SHEAVE

This small block is used on trapeze adjustment systems where the removable sheave enables installation without cutting wires.

Specifications: 1-3/16" removable sheave, Teflon® bearing and 5/16" line capacity.

Hobie item #3103

SMALL BLOCK WITH REMOVABLE SHEAVE

H18 Angled Luff Batten Caps
Murrays Part# 012-4005
No more battens poking through next to the mast. Ten angled Tren Tec luff caps for Hobie® 18 prevent batten splitting and align batten to the angle of the sail, increasing the life of your sail. Glue to the forward end of the batten.
Hobie Part# 1563
Sold in packages of 10

H-18 ANGLED LUFF BATTEN CAPS

Rear Mast Support with "V"

Murrays Part# 13-3002

REAR MAST SUPPORT WITH "V"

Hull Cradle: Bow

Murrays Part# 13-7030

HULL CRADLE: BOW

Quick Release Deluxe Pin 1/4 X 1.25"
Murrays Part# 18-4M125
This quick release pin features a push button on the top that releases 2 spring-loaded balls at the tip that secure the pin in place. Also available with a lanyard, see related items below.

Uses:

This pin is recommended for connection of hiking stick to crossbar on all Hobie, Nacra and Prindle catamarans.
Also used on Hobie 18 SX and Hobie Magnum wings.
Compare to Hobie part# 20306 PIN, QR 1/4 X 1-1/4 CUP

QUICK RELEASE DELUXE PIN 1/4 X 1-1/4"

EZ LOC UP-LOCK PIN KIT

Murrays PN 50-50314001

The EZ LOC UP-LOCK PIN KIT is the pin for locking Hobie Cat EZ Loc rudder system in up position during storage. EZ Loc up-lock pin kit is the pin, screw, split rings and lanyard for securing the EZ Loc rudder in the up position.

Hobie Part Number 50314001

HOBIE EZ LOC UP LOCK PIN KIT

Hobie Wave Mast Step Post (Threaded)

Murrays Part# 50-38170001

This part is used on the Hobie Wave to connect the mast ball to the mast step casting on the front crossbar. The older waves utilize an H14 mast step casting.

Hobie Part# 38170001

WAVE MAST STEP POST (THREADED)

Washer 3/8 X 3/4 Nylon for 07-1953
Murrays Part# 50-8080691
Washer for tiller arm bolt #50-8040171. Hobie® factory item

WASHER NYLON 3/8 X 3/4"

Hobie® factory replacement end cap for Hobie 20-style tiller connector and adjuster kit (#07-1953). Hobie part number 40561001 and 40561000

Hobie 1953 tiller connection kit - new style

H-20-1995 & LATER TILLER CONNECTOR END CAP

H18 Mast Bearing

Murrays Part# 50-60110000

Hobie Cat® factory mast bearing for Hobie 18. This part sits on the mast step to facilitate mast rotation on the Hobie 18.

Hobie part# 60110000

H-18 MAST BEARING

Screw PHMS 1/4-20 X 1"
Stainless Steel

Murrays Part# 19-3020

Stainless steel, slotted pan head 1/4-20 x 1" machine screw to fasten mast bearing on pre-1990 Hobie® 18. Other uses include universal Prindle/Nacra bow plate and bow tang on Prindle 15/16/18/Escape.

Replaces Murrays item #56-F125.

1/4-20 X 1" Stainless Steel Screw

Harken 57mm Ratchet Block - Swivel, Becket, Cam Cleat
Murrays Part# 28-2139
Harken 57mm jib block is great for use on almost all Hobie Cat, Nacra and Prindle. Carbo Ratchets allow sailors to hand-hold loaded lines and offer balance between holding power and controlled easing.
Specifications
Sheave diameter: 2-1/4"
Length: 4-15/16"
Weight: 9 oz
Shackle pin diameter: 3/16"
Maximum line diameter: 3/8"
Maximum working load: 600 lb.
Breaking load: 1500 lb.

HARKEN 57MM RATCHET BLOCK- SWIVEL, BECKET, CAM CLEAT

Murrays Hobie Getaway Turquoise Jib Sail - 37992071

GETAWAY JIB - TURQUOISE

Coffee Marine Bridle Vane XL
Murrays Part# 001-7080
compare to Hobie 7703

XL Bridle Vane - Wave & 17

H16 Jib Sail (White)

Murrays Part# 50-20992010

This is an OEM Hobie White Jib for the Hobie 16 sailboat. This is class legal for One Design Hobie Racing. This sail includes batten ties

H-16 JIB SAIL (WHITE)

Previous 1 … 11 12 13 14 15 … 57 Next

Recently viewed

All Sailing Parts