All Sailing Parts

All Sailing Parts

2262 products

Everything Nacra, Prindle, Hobie and a few more fun odds and ends.

2262 products

Sort

Tear-Aid Type A is the best-known kite and sail repair tape and it works on all kite canopy / sail materials: Dacron, mylar and ripstop nylon and kite bladders. Each package includes one foot of clear repair tape, alcohol pad and instructions. To use, clean area to be repaired with alcohol, cut patch to size, then peel and stick.

TEAR-AID KITE/SAIL REPAIR PATCH (3x12")

Batten Cap Leech Adjustable H16 Jib Each

Murrays Part# 012-3004-1

No more knots at the trailing edge. Adjust Hobie® 16 jib sail shape in seconds without tying and untying knots. Release tension to prolong sail shape and life. Individual cap.

Sold Individually

ADJUSTABLE LEECH JIB BATTEN CAP (EA)

H20 Upper Rudder Slack Bushing

Murrays Part# 50-40340001

This is the upper bushing for the Hobie Miracle 20 rudder casting. This uses the 5/16" stock rudder pins.

Hobie Part# 40340001

H-20 UPPER RUDDER SLACK BUSHING

H20 Lower Rudder Slack Bushing

Murrays Part# 50-40360001

This is the lower bushing for the Hobie Miracle 20 rudder casting. This uses the 5/16" stock rudder pins.

Compare to Hobie Part# 40360001

H-20 LOWER RUDDER SLACK BUSHING

Mast Float Mount Plate

Murrays Part# 50-39640020

Mast float plate for the Hobie Baby Bob and the Mama Bob.

Sold individually

Hobie Part# 39640020

MAST FLOAT MOUNT PLATE

Hobie Wave Jib Spreader End Cap

Murrays Part# 50-38950011

This is part of the Wave bow spreader kit. These go into the ends of the spreader pole. Replacement end cap for Hobie Wave jib spreader assembly.

Sold individually
Hobie Part# 38950011

WAVE JIB SPREADER END CAP

Swivel Mount Base with Fasteners

Murrays Part# 007-1162

The offset base pad kit fits Hobie® and Prindle elliptical crossbars. Includes injection-molded plastic base and fasteners.

Replacement fasteners are also available (requires 3 self-tapping screws #19-1620, 1 machine screw #19-1516, and 1 nut #19-2016).

Hobie Cat® Part# 1162

PRINDLE SWIVEL MOUNT BASE WITH FASTENERS

H14/16 Upper Gudgeon

Murrays Part# 25-3351

This latest, strongest design with welded sleeve bushings provides large, smooth bearing surfaces between rudder pins and gudgeons. Replace flared gudgeons with their sharp edges and point loading that can cause early rudder pin failure. For Hobie® 14's, 16's and 17, order separate upper and lower gudgeons.

 For all other Hobie® cats Part# 25-3352 for both gudgeons. Each

This gudgeon is a replacement for item #50101301

Upper rudder gudgeon for the Hobie 14 and 16. This updated, strongest design with welded sleeve bushings provides large, smooth bearing surfaces between rudder pins and gudgeons. Replace flared gudgeons with their sharp edges and point loading that can cause early rudder pin failure. For Hobie 14's, 16's and 17, order separate upper and lower gudgeons.

 For all other Hobie® cats Part# 25-3352 for both gudgeons. Each

This gudgeon is a replacement for item #50101301

H-14/16 UPPER GUDGEON

Harken 29mm Bullet Sheave

Murrays Part# 28-0160

Harken's downhaul/halyard sheave makes raising the sail and/or adjusting the downhaul with Harken ball bearing sheaves much easier. This is a direct replacement for the sheaves that came with early Hobie 17s.

HARKEN 29MM BULLET SHEAVE

Clew Kit 5-Hole (H16 Jib)

Murrays Part# 001-1012

Clew kit for Hobie® 16 jib includes one pair of anodized aluminum plates with rivets to be set with a hammer. Each plate has five holes and measures 8" maximum length by 1-1/2" wide. Replacement rivets are available separately (#19-5006).

This product replaces discontinued item #50-22240000.

H-16 5 HOLE JIB CLEW KIT

Shock Cord Dyneema Cover 4mm - White

Murrays Part# 39-7391D

Robline 4mm Dyneema coated bungee.

Robline part number DSC-4W

DYNEEMA SHOCK CORD 3MM

Quick Release Pin Deluxe 3/16 X 1"

Murrays Part# 18-3M100

This convenient pin features a deluxe dished head with a hole for lanyard attachment. No other locking pin is faster operating or safer.

The pin is also available with a 1/16" x 7" stainless lanyard with nicropress ovals (see related items). Measurements for this quick pin with cup head are 3/16" diameter x 1" maximum grip length (distance from the shoulder to the locking ball bearings).

QUICK RELEASE PIN DELUXE 3/16 X 1"

The Selma fid (needle) is the only tool for splicing all kinds of rope. Selma fids are made of highly polished stainless steel. Made in Norway and patented worldwide.

Please note that the appropriate fid size will depend on the type and construction of line. The purchase of a set of 4 or 5 fids may be a better option if you are unsure of the fid size you need.

SELMA FID 5.5mm 1/4-5/16"

The Quick-Release Pin Deluxe 3/16 X 1″ with Lanyard features a deluxe dished head and a lanyard to help prevent loss. No other locking pin is faster operating or safer. The pin with cup head includes a stainless lanyard that comes secured on one end with a nicropress oval; the other end is left open so that you can secure with included nicropress oval after attaching the lanyard to your chosen location.

This Quick Release Pin features 2 locking balls for a extra secure grip, push button deluxe dished head,

QUICK RELEASE PIN 3/16 X 1 WITH LANYARD

Mast Rotation Control Arm

Murrays Part# 25-3040

Stainless mast rotation control arm is strong and smooth! Arm #25-3040 with 1/4″ hole is for all Hobies except for the Hobie® 17, Prindles and Nacras; Arm #25-3041 with 5/16″ hole is for Nacras, Prindles and the Hobie® 17. H17 uses #19-2235 bolt

Hobie Part# 61210001

MAST ROTATION CONTROL ARM

Hobie 16 jib sail, blue

Prindle Rudder Lower Plastic Spacer

Murrays Part# 56-4014

Prindle Rudder Lower Plastic Spacer is used on the rudder systems of all Prindle models. Performance Sports factory item #4014. 9/16″ wide x 1/2″ diameter, 1/4″ hole.

ILLUSTRATED PRNDLE RUDDER PARTS LIST

PRINDLE LOWER RUDDER PLASTIC SPACER

Prindle rudder parts diagram

Prindle internal rudder components

PRINDLE RUDDER REFRESH KIT

Ronstan Halyard Shackle, 1/4" Pin

Murrays Part# 21-1033

The Ronstan Halyard Shackle with Twist Pin's main advantage is that you cant loose any of it once its attached. The top pin holds it on and the bottom pin dose not come out. Never loose your shackle pins again!

The 1/4" Halyard Shackle with Twist Pin is used in the following Murrays Products: 02-4383-50 N-5.5SL Jib Halyard w/Shackle

RONSTAN HALYARD SHACKLE, 1/4" PIN

Cat Trax Delrin Roller Bearing Set

Murrays Part# 13-1401-5

Set of 20 roller bushings for one Cat Trax wheel. Tiger Trax require 2 sets per wheel.

Sold in set of 20

CAT TRAX DELRIN ROLLER BEARING SET (20)

Ronstan Stainless Steel D Shackle, 1/4"

Murrays Part# 21-0617

UDL BL - The “Uniformly Distributed Load” breaking load of the shackle; the load is applied across the full span of the shackle pin. PL BL - The “Point Load” breaking load of the shackle; the load is only applied at the center or one side of the shackle pin.
Ronstan solid stainless steel shackle has 1/4" pin diameter. Having a spare on hand may mean the difference between sailing or not!

RONSTAN 1/4" D SHACKLE

PRINDLE JIB HALYARD WITH SISTER CLIPS

Cat Righter Uphaul: Cam-Clt 4:1

Murrays Part# 001-3273

This is the 4:1 block and tackle system only from Murrays' popular Cat Righting Big Bag System (#01-3280). Use with a righting bag to aid in righting a capsized catamaran.

CAT RIGHTER UPHAUL: CAM-CLEAT 4:1

Can't Hurt Trap Rings

Murrays Part# 001-0123

Can't Hurt Trap Rings are a light and flexible alternative to "hard" stainless steel dogbones. Black high pressure nylon tubing covers 1/8" (1x19) stainless wire.

Compare to Hobie Cat® #2003.

Sold in pairs

CAN'T HURT TRAP RINGS (PR)

Hobie 16 turquoise mesh trampoline Hobie 20970058

H-16 BLUE TRAMPOLINE WITH TEFLON THREAD

Screw 1/4-20 x 5/8 PHMS-P Stainless Steel
Murrays Part# 50-8030331
This screw is used on the Hobie wave to secure the eye straps to the inner edge of the crossbars for connecting the tramp pulleys on the classic wave or "other" on the club version.

SCREW 1/4-20 x 5/8" PHMS-P SS

H16/18/Getaway Mast Tang

Murrays Part# 50-20690000

Hobie® factory replacement mast tang for Hobie® 16, 18, Getaway and the 1995 and newer Hobie® 17. Use twelve 6-4 rivets (#19-5031) and twelve casings (#19-5020) for installation.

Also known as a mast hound

H-16/18/GETAWAY MAST TANG

HOBIE ROLLER FURLER DRUM ASSEMBLY

EZ Lock Lower Pintle

Murrays Part# 50-90880221

Hobie® factory replacement lower pintle for EZ Loc rudder system.

Fits Hobie Bravo, wave and Getaway boats

Hobie Part# 90880221

BRAVO/WAVE/GETAWAY EZ LOC LOWER PINTLE

H18 Cotter Pin for Traveler

Murrays Part# 50-8060121

Hobie® factory replacement 3/32" x 2" stainless steel cotter pin is used on Hobie 18 main traveler car.

Hobie Part# 8060121

H-18 COTTER PIN FOR TRAVELER

TRAMP CLAMP (10)

Minimize chafing at trampoline stress points and reduce the possibility of the trampoline pulling out of the aluminum extrusion. Clamps slide into the aluminum extrusion track. 10 pieces, 1.5" long. By Tren Tec.™ Hobie Cat® uses #2066 for this item

TRAMP CLAMP (10)

Replacement Sheave Prindle Rudder Upper

Ronstan PN RF1741

Replacement sheave for upper part of rudder casting on all models of Prindle catamarans. Replacement for Performance Sports item #4009. 1/4" wide x 3/4" diameter, 1/4" hole.

ILLUSTRATED PRNDLE RUDDER PARTS LIST

RONSTAN 19MM ACETAL SHEAVE, 6MM WIDTH

Harken 29mm Bullet Block

Murrays Part# 28-0082

Medium-size Harken single bullet block with Delrin® ball bearings works well for control line or jib sheeting lines. The low-friction bullet block is compact and lightweight, with fast trim and release under high or low loads.

HARKEN 29MM BULLET BLOCK

H20 Shroud 5/32" Black Wire Roller Swaged

Murrays Part# 002-0705-12

Single shroud (sidestay) for Hobie® 20 is constructed to factory specifications. Hydraulic swaging produces a cleaner, stronger shroud than standard double swaging.

Compare to Hobie Cat® Part# 40792001

H-20 SHROUD 5/32" BLACK WIRE ROLLER SWAGED

1/4" QUICK RELEASE BOW SHACKLE

O’Pen Skiff Hiking Strap

Murrays Part# 65-53263

Padded booster strap

What O’Pen says about the Skiff:

For fun, recreation, perfection and racing! The O’pen BIC sailing dinghy is a breath of fresh air for junior sailing. Based on a modern skiff concept, the O’Pen BIC is very fast, very simple, and very FUN to sail! The self-bailing open transom hull is rapid and responsive, with a modern rig that’s rugged and versatile.

O'PEN SKIFF HIKING STRAP

Nacra Main Halyard Ring with Shackle

Murrays Part# 56-30312

This shackle connects your Mainsail on your mast, it's knotted on your main halyard.
It takes your Mainsail through the slot of your mast to the top where it connects with the Mainsail hook.

NACRA MAIN HALYARD RING WITH SHACKLE

Rooster Tell Tails
Murrays Part# 48-101579
The Rooster Tell Tails come in a pack of three green and three red self adhesive wool telltales (with TEFLON® treatment) that don´t stick to the sail when they are wet.

ROOSTER TELL TAILS

The Selma fid (needle) is the only tool for splicing all kinds of rope. Selma fids are made of highly polished stainless steel. Made in Norway and patented worldwide.

Please note that the appropriate fid size will depend on the type and construction of line. The purchase of a set of 4 or 5 fids may be a better option if you are unsure of the fid size you need.

SELMA FID 7.5mm 5/16-3/8"

50102020 - Hobie 16 One Piece Gudgeon Middle Bushing Insert

H-16 ONE PIECE GUDGEON MIDDLE BUSHING INSERT

Previous 1 … 8 9 10 11 12 … 57 Next

Recently viewed

All Sailing Parts