Murrays.com Hobie shroud, forestay, halyard, mast bearing

Murrays

800 products

Hobie, Nacra and Prindle rigging: shrouds, halyards, bridles, forestays and small parts like mast bearings, trapeze handles, rudder cam kits, rudder pins, righting lines and more.

800 products

Sort

Boom Outhaul Bearing H18
Murrays Part# 50-60240000
Boom bearing for Hobie 18 outhaul system

H-18 BOOM OUTHAUL BEARING

Tiller Crossbar Adjustable Cap Kit

Murrays Part# 50-60400011M

Murrays Tiller Crossbar Adjustable Cap Kit installs in the end of the Hobie tiller crossbar and allows you to adjust the width of the crossbar which controls the angel of the rudders.

Hobie discontinued this part and this is a Murrays Replacement part that we have made here in California.

Applications: H14, H16, H17, H18, Hobie 18 SX tiller x-bar

Tiller Crossbar Adjuster: 1

HOBIE TILLER CROSSBAR ADJUSTABLE END CAP - 60400011

Prop Guard Torqeedo Travel Motor

The Murrays Torqeedo Prop Guard is designed for use on the Torqeedo 503, 1003, 1103, 1103AC and 603 electric motors. Our Prop Guard protects the propeller from rocks, debris, and fishing line.

These are made to fit specific models of Motors, so please select your motor carefully from the drop down options above. The Travel motors were updated in 2021 to the 603 and 1103 versions.

PROPELLER GUARD TORQEEDO TRAVEL MOTOR

Hobie 20 TRAPEZE WIRE 40504501

H-20 DOUBLE TRAPEZE (4)

Hull Cradle: Bow

Murrays Part# 13-7030

HULL CRADLE: BOW

Replaceable Aluminum Trap Handle

Murrays Part# 007-2010

Foam-covered aluminum handle is easily installed onto existing trapeze wire. Carry a spare as a temporary repair, then replace the wire at your convenience. Each.

Hobie Cat® Part# 2010

REPLACABLE ALUMINUM TRAP HANDLE

Murrays M8 x 25mm Titanium Hydrofoil Screws

M8x25mm TITANIUM TORX BOLT

O’Pen Skiff Tiller End Plug
Murrays Upgrade

Murrays Part# 65-316970

The O’Pen Skiff Tiller End Plug Murrays Upgrade is the solution to a weak point on the O’Pen Skiff boat. This upgrade replaces the two standard tiller end plugs that go on each pintle. Only two are required instead of four because the Murrays Tiller end plug is solid and spans the whole distance inside the rudder housing. So you don't need two per pintle only per rudder.

O'PEN SKIFF TILLER END PLUG (MURRAYS UPGRADE)

Nylon Port Fastener Kit

The Port Nylon Fastener Kit includes all the necessary nylon fasteners (screws, washers and nuts) plus marine silicone sealant for the installation of two access ports, also known as hatches, on to a catamaran like a Hobie, Nacra or Prindle.

Use this page to order:
001-1159 White
001-1160 Black

NYLON PORT FASTENER KIT

Hobie 16 turquoise mesh trampoline Hobie 20970058

WAVE 3-PIECE CLUB TRAMPOLINE WITH TEFLON THREAD-LAKE BLUE

1/2 BALL (NYLON) - Hobie half round washer spacer tiller connector - Hobie part number 11510000 HOBIE HALF SPHERE TILLER CONNECTOR

Tiller Connection Kit
Murrays Part# 001-2061
The Murrays Tiller Connection Kit assures consistent rudder alignment through the full rudder sweep. Spring-loaded half balls and contoured spacers take the slop out of the tiller-to-crossbar connection on Hobie Cats. Racing class legal. Each kit contains 2 connectors to join the tiller crossbar to the tiller arms. Compare to Hobie Cat® #3052.
Applications:; Hobie 14, 16, 17, 18, 18SX

NYLON 1/2" BALL

H20 Forestay Roller Furling 5/32" Black Wire

Murrays Part# 002-0745-32

Lower forestay for Hobie® 20 with roller furling setup. Constructed to factory specifications. 

Compare to Hobie Cat® Part# 48814001

H-20 FORESTAY ROLLER FURLING 5/32" BLACK WIRE

H-16 BLACK MESH TRAMPOLINE-BLACK

Headboard Replacement Kit

Murrays Part# 001-1014

Headboard Replacement Kit includes one pair of anodized aluminum plates with rivets to be set with a hammer. Plates measure 5" high x 4" wide x 6-1/4 diagonal. Replacement rivets are available separately (#19-5006).

HEADBOARD REPLACEMENT KIT

H20 Upper Forestay 5/32" Black Wire with Roller Furling

Murrays Part# 002-0735-02

Black upper forestay for Hobie® 20 with roller furling setup. Constructed to factory specifications.

Compare to Hobie Cat® Part# 40810011

H-20 UPPER FORESTAY 5/32" BLACK WIRE WITH ROLLER FURLING

Quick-Release Convenience Package: H16

Murrays Part# 001-3231

This package makes set-up and take-down of your Hobie 16® more convenient.

Kit includes:

One #18-4R125 Quick Release Pin for hiking stick to crossbar connection.
One #18-3M075L Quick Release Pin with Lanyard for mainsheet block to traveler car connection.
One #21-1032 Quick Twist Halyard Shackle for jibsheet blocks to jib clew boom to mast connection.
One #21-1155L Toggle Pin with Lanyard for forestay to adjuster connection.
Four #01-0127 Car

H-16 QUICK RELEASE CONVENIENCE PACKAGE

SMALL BLOCK W/REMOVABLE SHEAVE

This small block is used on trapeze adjustment systems where the removable sheave enables installation without cutting wires.

Specifications: 1-3/16" removable sheave, Teflon® bearing and 5/16" line capacity.

Hobie item #3103

SMALL BLOCK W/REMOVABLE SHEAVE

This small block is used on trapeze adjustment systems where the removable sheave enables installation without cutting wires.

Specifications: 1-3/16" removable sheave, Teflon® bearing and 5/16" line capacity.

Hobie item #3103

SMALL BLOCK WITH REMOVABLE SHEAVE

Rudder Pin Nacra, Prindle and H21 (Aluminum)

Murrays Part# 001-5272

Aluminum rudder pins for Nacra, Prindle and Hobie® 21 measure 3/8" x 10-1/4" end-to-end, with hole at each end. Cotter pins are included.

Sold in pairs

NACRA/PRINDLE AND H21 ALUMINIUM RUDDER PIN

H18 Black 3 Piece Trampoline

Murrays Part# 30-3103

Murrays black mesh tramp for Hobie® 18 is not Class-legal for racing. Polypropylene mesh is the ideal material for beach cat tramps because it is light, strong and comfortable with very good UV resistance, plus it allows water to drain, so you won't be sitting in a puddle. The Hobie 18 version comes with a sewn in pocket in the front for your halyard and jib furling line.

H-18 3PC MESH TRAMPOLINE-BLACK

H-16 ROLLER FURLING JIB KIT

The Murrays Hobie Getaway line package contrains all the lines on a Hobie Getaway. The Main and Jib sheets are Robline Neptune 500 and the control lines are Pelican VLS, Very Low Stretch.

H-GETAWAY LINE PACKAGE

Rear Mast Support with "V"

Murrays Part# 13-3002

REAR MAST SUPPORT WITH "V"

M6 x 25mm Titanium Hydrofoil Screws
Murrays Part# 55-0025T
The M6 x 25mm Titanium Hydrofoil Screws are stronger and more corrosion resistant than stainless steal foil hardware. Compatible with all M6 foil track inserts. The 25mm length is used for both board to foil connection as well as foil assembly. Commonly used with F-One, Naish, Airush, Takuma, Axis, Sab foil, Armstrong and more. Titanium foil hardware does not require greasing or regular checking. Titanium does not corrode or seize

M6 x 25mm Titanium Hydrofoil Screws
Murrays Part# 55-0025T
The M6 x 25mm Titanium Hydrofoil Screws are stronger and more corrosion resistant than stainless steal foil hardware. Compatible with all M6 foil track inserts. The 25mm length is used for both board to foil connection as well as foil assembly. Commonly used with F-One, Naish, Airush, Takuma, Axis, Sab foil, Armstrong and more. Titanium foil hardware does not require greasing or regular checking. Titanium does not corrode or seize

M6x25MM TITANIUM HYDROFOIL SCREWS

EYE STRAP KIT - 2072

WAVE SAIL BAG DELUXE

3-Hole Pad Kit

Murrays Part# 001-0110

This base kit is for Harken®, Hobie® or Murray 360 cleats without swivel base adapters. Kit includes one 3-hole base, one swivel base adapter (#25-3001), plus three #10 FHSMS (#19-1626). Ronstan swivel 360 cleats include swivel base adapters, so this kit is not necessary. Fits Hobie® or Prindle elliptical crossbar.

H20 Jib Halyard Roller Furling

Murrays Part# 002-0786-00

Jib halyard for Hobie® 20 with roller furling is constructed to factory specifications. Order 24' of #39-0221 1/8" Dacron line for jib halyard line.

Compare to Hobie Cat® Part# 48661001

H-20 JIB HALYARD ROLLER FURLING

H18 Assembly Manual

Murrays Part# 50-63450000

Printout of H18 assembly manual PDF.

H-18 ASSEMBLY MANUAL

WING MOUNT KIT (1 EACH)

Murrays PN 50-65071001

Hardware mounting kit for Hobie 18 Magnum and SX wings. 

Includes:

2 x Wing Slug - Threaded post

2 x 5/16 -18 threaded nylock nuts
2 x 5/16 -18 Socket Screw

WING MOUNT KIT (1 EACH)

65071001

Hardware mounting kit for Hobie 18 Magnum and SX wings. 

Includes:

2 x Wing Slug - Threaded post

2 x 5/16 -18 threaded nylock nuts
2 x 5/16 -18 Socket Screw

WING MOUNT KIT (1 EACH)

104" Hobie batten part number 21000001

H-16 MAINSAIL FIBERGLASS BATTEN 107"

Murrays Hobie 18 Jib sail

Getaway Aft Mesh Trampoline
Pre 2017-Black

The Murrays Getaway Aft Black Mesh Trampoline is a 2 piece trampoline for a Hobie Getaway that comes with a 12" halyard pocket, hiking strap and robust Polypropylene mesh and UV treated Polyester thread. We also offer an optional upgrade to Teflon thread extends the life of the tramp is available for an additional charge which we recommend for boats that are primarily in direct sun, as it has better UV resistance properties.

GETAWAY AFT 2-PIECE MESH TRAMPOLINE PRE 2017-BLACK

H-14 TURBO BRIDLE 1/8
One bridle for Hobie 14 Turbo constructed of 1/8" 1x19 wire to factory specifications.

Turbo typically refers to the Hobie Factory Version that features a Hobie Roller furling drum, bridles connect to the drum with forks, and an under tramp jib block wire.

Use this page to order product numbers:

02-0114-21 White (compare to Hobie Cat® #10820011)
02-0114-22 Black bridle for Hobie 14 Turbo (compare to Hobie Cat® #10822010 black)

Murrays PN 002-0114-21 and 002-0114-22

H-14 TURBO BRIDLE 1/8" WIRE

Mainsheet for a Hobie Wave sailboat made of Dacron Spun Braid. Dacron Spun Braid was the OEM sheeting line for Hobie up into the late 90s. Dacron Spun Braid has excellent grip, cleats well and is easy on the hands.

35' of 3/8 Soft Dacron Spun Braid with a strong polyester blend core.

This was the stock Hobie mainsheet line from the 80s and 90s. Very little stretch, soft hand, easy cleating.

Mainsheet for a Hobie Wave sailboat made of Dacron Spun Braid. Dacron Spun Braid was the OEM sheeting line for Hobie up into the late 90s. Dacron Spun Braid has excellent grip, cleats well and is easy on the hands.

35' of 3/8 Soft Dacron Spun Braid with a strong polyester blend core.

This was the stock Hobie mainsheet line from the 80s and 90s. Very little stretch, soft hand, easy cleating.

H WAVE MAINSHEET

Coffee Marine Bridle Vane Replacement Vane

Murrays PN 001-7050-G

Sensitive, rigid and light! The classic bridle vane for the Hobie 16 and other racing cats. These are made in our warehouse and will fit the Hobie Bridle Vane assembly or the classic Coffee Marine assemblies. The Coffee Marine vanes are slightly more rigid than the Hobie wind vane, making them last longer and less likely to flap in the wind.

Compatible with Hobie Bridle vanes.

Hobie part number CM7703

Coffee Marine Bridle Vane Replacement Vane

Coffee Marine Bridle Vane XL
Murrays Part# 001-7080
compare to Hobie 7703

XL Bridle Vane - Wave & 17

HEAVY DUTY SWIVEL WITH ALUMINUM CAM & BULLSEYE

H20 Bridle 5/32" Black Wire

Murrays Part# 002-0715-22

One bridle for Hobie® 20 is constructed to factory specifications. 

Compare to Hobie Cat® Part# 40822001

H-20 BRIDLE 5/32" BLACK WIRE

H18SX Jib Halyard with Shackle

Murrays Part# 002-0686-00

Jib halyard with shackle for Hobie® 18SX is constructed to factory specifications.;

Use 20' of 1/8" line to to complete your jib halyard or our jib halyard kit with sister clips. links below in related items.

Compare to Hobie Cat® Part# 68661001

H-18SX JIB HALYARD WITH SHACKLE

Previous 1 … 4 5 6 7 8 … 20 Next

Recently viewed

Murrays