Murrays Marine - Catamaran specialists

All

3171 products

    All Murrays Products: Hobie, Nacra, Prindle rigging, rudder parts, sails, trampolines, spare parts, lines and more. 

    3171 products
    Black Mast Caution Decal Murrays Part# 50-13440000 The Decal Mast Caution Black Hobie® factory caution decal attaches to mast as a reminder to watch for overhead power lines when sailing and/or launching your boat.
    BLACK MAST CAUTION DECAL
    Hobie
    Sale
    The Dakine Nitrous Shorts Harness also known as the Dakine Nitrous Shorts are Dakine's most minimalist seat harness draped in board shorts. The Nitrous Shorts offer a very low spreader hook height and unhindered range of motion. The Nitrous shorts are one of Dakine’s lightest and most compact harnesses, they offer great freedom of movement with minimal padding that is only located where needed. Nitrous shorts are ideal for people with short arms, back pain, from foiling to kitesurfing.
    DAKINE NITROUS SHORTS HARNESS
    Dakine
    Save $50
    Harken 6mm "D" Shackle Murrays Part# 28-2108 For use with Harken main sheet blocks. Forged stainless steel shackles are polished to a high luster and are stamped with the screw pin diameter. "D" shackles are the most common type of shackle. They are best suited for aligned attachment points.
    HARKEN 6MM "D" SHACKLE
    Harken
    Robline waxed whipping twine
    WHIPPING TWINE - WHITE SPOOL
    Robline
    Out of Stock
    Hobie Wave Mast Step Post (Threaded) Murrays Part# 50-38170001 This part is used on the Hobie Wave to connect the mast ball to the mast step casting on the front crossbar. The older waves utilize an H14 mast step casting. Hobie Part# 38170001
    WAVE MAST STEP POST (THREADED)
    Hobie
    Out of Stock
    HOBIE WAVE EZ LOC TILLER CROSS BAR Murrays PN 50-39524001 Hobie® factory replacement tiller crossbar assembly for Wave with EZ Loc rudder system. Hobie part number 39524001
    WAVE EASY LOC TILLER CROSS BAR
    Hobie
    Hobie Wave Keeper Pin With Lanyard Murrays Part# 50-38490011 Hobie® factory replacement keeper wire with pin for Wave and Getaway. Hobie part# 38490011
    WAVE KEEPER PIN WITH LANYARD
    Hobie
    TORQEEDO MAGNETIC KEY
    Torqeedo
    Murrays Part# 50-10432000 Hobie® factory 2½" spring for Hobie® 16 lower rudder casting. This spring is longer and stiffer than original equipment (#50-10430000), providing additional tension if you are having trouble with rudder kick up. Used on Hobie 18 Rudder Systems from late 80s through now. Used on Hobie 16 Rudder Systems after 1983 Used on Hobie Getaway Rudder Systems pre- EZ Loc Hobie part number 10432000
    HOBIE RUDDER SPRING-LONG
    Hobie
    H18/20 Outhaul Car Bearing Pin Murrays Part# 50-60250000 This pin is used to hole the bearings on the traveler car for an H-18 or Miracle 20 beachcat. This pin has been discontinued by Hobie, this part meets or exceeds OEM quality and specification. Compare to Hobie Part# 6025000
    H-18/20 OUTHAUL CAR BEARING PIN
    Hobie
    Nylon Washer Internal Casting Prindle Murrays Part# 56-F118 Nylon washer is used on Prindle rudder casting to separate the upper sheaves to help keep the line from fouling. Order four per side to remove as much slop as possible. Performance Sports factory item #F118
    PRINDLE NYLON WASHER INTERNAL CASTING
    NACRA
    Tiller Tie Bar Kit Murrays Part# 56-5516 The Nacra Tiller Tie Bar Kit provides improved tiller connect for older Nacras. Nacra Sailing factory item# 30149 and 30150
    NACRA TILLER TIE BAR KIT
    NACRA
    Out of Stock
    Dakine Core Contour 3 Foot Straps Murrays Part# 32-485394
    DAKINE CORE CONTOUR 3 FOOT STRAPS
    Dakine
    Save $40
    Hobie Boom Blocker Hanger  Murrays Part# 50-10760000 Hobie factory boom block hanger for the Hobie 14, 16, 17 and 18. Hole spacing is 1-1/8".  Use four 6-4 rivets (#19-5031) for installation.
    HOBIE BOOM BLOCKER HANGER
    Hobie
    Batten Cap Main Luff (EA) Murrays Part# 50-11322011 Main luff batten cap for Hobie Cats are sold individually. Order batten tie separately; 18" of line per batten cap is standard. Hobie® factory replacement part.
    MAIN LUFF BATTEN CAP (EA)
    Hobie
    #4 Spur Grommets Set of 24
    GROMMET #4 SPUR Set of 24
    Misc
    Trap Shock Cord Kit: H20 Murrays Part# 001-0131 A trapeze shock cord is an absolute necessity because it keeps the trapeze system in place and ready for hook-up. One hook connects to either the thimble on the trapeze wire or the adjustment line, then runs under the tramp and connects to the other side in the same location. Our shock cord kit comes with one plastic carbine hook installed; the other hook is installed after lacing shock cord through trampoline grommets. Kit includes two lengths of 1/4" shock
    H-20 TRAP SHOCK CORD KIT
    Murrays Sports
    Screw PHMS 1/4-20 X 1" Stainless Steel Murrays Part# 19-3020 Stainless steel, slotted pan head 1/4-20 x 1" machine screw to fasten mast bearing on pre-1990 Hobie® 18. Other uses include universal Prindle/Nacra bow plate and bow tang on Prindle 15/16/18/Escape. Replaces Murrays item #56-F125.
    1/4-20 X 1" Stainless Steel Screw
    Misc
    Screw PHMS #10-32 X 5/8" Stainless Steel Murrays Part# 19-2910 Stainless steel, pan Phillips head, #10-32 x 5/8" machine screw.
    SCREW PHMS #10-32 X 5/8 (SS)
    Misc
    Ronstan Series 20 Utility Block, Tube Rivet Murrays Part# 21-0661 Rontan's cheek block is a Hobie® 18 and Prindle downhaul and turning block. Stainless steel cheeks and Acetal sheaves ensure a long service life with virtually no maintenance. Hollow rivets in the block heads can be fitted with shackles, which can also be used to add a becket for extra purchase.
    RONSTAN MIDGET SINGLE BLOCK (CHEEK)
    Ronstan
    Out of Stock
    Quick Release Deluxe Pin 1/4 X 1.25" Murrays Part# 18-4M125 This quick release pin features a push button on the top that releases 2 spring-loaded balls at the tip that secure the pin in place. Also available with a lanyard, see related items below. Uses: This pin is recommended for connection of hiking stick to crossbar on all Hobie, Nacra and Prindle catamarans. Also used on Hobie 18 SX and Hobie Magnum wings. Compare to Hobie part# 20306 PIN, QR 1/4 X 1-1/4 CUP
    QUICK RELEASE DELUXE PIN 1/4 X 1-1/4"
    Misc
    Out of Stock
    Hobie 3062 1/4" Bow shackle with quick release pin
    QUICK RELEASE 1/4" BOW SHACKLE
    Murrays Sports
    Quick Release Pin Detent 1/4 X 1" Murrays Part# 18-4D100 This quick pin has a spring-loaded ball that exerts sufficient pressure to help avoid accidental release. Measures 1/4" diameter x 1" long. Can be used to replace 1/4" clevis pins up to 1" long.  Not recommended for use in shroud adjusters or chain plates.
    QUICK RELEASE PIN DETENT 1/4 X 1"
    Misc
    Oxen blocks are the ultimate high tech, self-holding jib blocks that offer a real advantage over blocks with cleats! Get fast, simple mainsheet (and jibsheet) control: just pull-to-cleat, then pull-to release! Cleat or uncleat your jib or mainsheet every time without looking and from any position. Cleat from any angle or position on the boat, including the wings, even if your sheet passes over something en route. Oxen blocks are easy to install and foolproof to use. Expensive, but the best is rarely cheap!
    OXEN BLOCK WITH PIN
    Oxen
    Nut Nylock 1/2-13" Stainless Steel Thin Murrays Part# 19-2531 Thin stainless steel 1/2-13 hex nut with nylock insert will not rust or work loose if properly installed. Used on 1/2" pylon bolt on most older Hobie 16's (changed to 3/8" in 1994). Equivalent to Hobie #8050631.
    NUT NYLOCK 1/2-13 (SS) THIN
    Misc
    he comfortable, 6" adjustable foot straps feature 7mm neoprene padding to comfortably accommodate bare feet or sailing shoes. Their pre-formed arch eliminates collapsing and the exterior hook and loop closure system allows for quick and easy adjustment. Drilling instructions and self-tapping screws are included.
    DAKINE CATAMARAN FOOTSTRAP KIT (PR)
    Dakine
    Cat Trax Axle Hose Cover Murrays Part# 13-1401-6 Replacement hose cover for Cat Trax axle helps cushion your boat's hulls. Item sold individually
    CAT TRAX AXLE HOSE COVER (EA)
    Cat Trax
    Port Cat Bag 5" Murrays Part# 001-1178 The Cat Bag provides handy storage inside a deck port! Designed to hang inside 5" access port (#01-4210 or #01-4210BK) on a molded shoulder. Details: 12" deep Comes in one color: red Metal collar - gap in ring for easy installation Cinch bag style
    5" PORT CAT BAG
    Sea Dog
    H18 Main Adjustable Batten Leech Caps Murrays Part# 012-4003 No more knots at the trailing edge. Adjust Hobie® 18 main sail shape in seconds without tying and untying knots. Release tension to prolong sail shape and life. Hobie Part# 1523 Sold in packages of 10
    H-18 MAIN ADJUSTABLE BATTEN LEECH CAPS (10)
    Tren-Tec
    1/2 BALL (NYLON) - Hobie half round washer spacer tiller connector - Hobie part number 11510000 HOBIE HALF SPHERE TILLER CONNECTOR
    Tiller Connection Kit Murrays Part# 001-2061 The Murrays Tiller Connection Kit assures consistent rudder alignment through the full rudder sweep. Spring-loaded half balls and contoured spacers take the slop out of the tiller-to-crossbar connection on Hobie Cats. Racing class legal. Each kit contains 2 connectors to join the tiller crossbar to the tiller arms. Compare to Hobie Cat® #3052. Applications:; Hobie 14, 16, 17, 18, 18SX
    NYLON 1/2" BALL
    Murrays Sports
    P16 Mesh Trampoline-Black Murrays Part# 30-3122 Black mesh tramp for Prindle 16 includes cut-outs for ports. Hiking straps are installed and one pocket is included. Polypropylene mesh is the ideal material for beach cat tramps because it is light, strong and comfortable with very good UV resistance, plus it allows water to drain, so you won't be sitting in a puddle. Order lacing line separately.
    PRINDLE 16 MESH TRAMPOLINE-BLACK
    Murrays Sports
    CAT TRAX WIDE HULL CRADLES
    Cat Trax
    Out of Stock
    Eyelet Post H20 Murrays Part# 50-41220001 The Eyelet Post H20 Hobie® factory replacement eyelet post for Hobie® 20 rear crossbar. This item replaces tie button for Inter cats #56-9882. Fits Hobie Getaway Rear Crossbar
    H-20 EYELET POST
    Hobie
    Harken 57mm Carbo 8:1 System Murrays Part# 28-81 Lightweight, low profile and very strong, these Carbo AirBlocks® have enormous working range, with a higher working load than standard blocks, even though they are lighter in weight! The Carbo Ratchmatic® is a load-sensing ratchet block that rolls freely in both directions under low loads, and automatically engages the ratchet as loads increase.
    HARKEN 57mm CARBO 8:1 SYSTEM
    Harken
    Sale
    Jib track 5/8” used
    Murrays Sports
    Save $15
    Harken 38mm Low-profile Standard Eyestrap Murrays Part# 28-0201 The eyestrap low-profile SS (ST-2013)- Eyestraps are useful accessories. They form light-duty mounting bases for blocks, serve as lash-down points, and can be used for fairleads.
    HARKEN 38MM LOW-PROFILE STANDARD EYE STRAP
    Harken
    Hobie Wave EZ Loc Rudder Assembly Murrays Part# 50-39312000 EZ Loc rudder assembly for the Hobie Wave. Hobie Part# 39312000
    WAVE EZ LOC RUDDER ASSEMBLY
    Hobie
    Out of Stock
    Hobie 16 Jib Batten Cap Kit The Hobie 16 jib batten cap kit includes 4 jib batten leech caps and 4 batten tie lines. Hobie part number 1531 Hobie 16 jib batten cap part number 21333000
    H-16 JIB BATTEN CAP KIT
    Hobie
    Spare Parts Kit: Wave and Getaway, Hobie part number 30308
    WAVE/GETAWAY SPARE PARTS KIT
    Murrays Sports
    Out of Stock
    Light, compact, and easy to use, the F-One STRIKE CWC V3 is the quintessential light-wind weapon. Our patented 3-strut wing has proven to be the ideal concept for a successful large surface wing, and the STRIKE CWC has dominated light-wind wing foiling since its appearance on the market. Featuring a new and revolutionary design as well as F-ONE’s latest technologies and materials, this CWC V3 will let you show off your wing foiling skills in full confidence on any light wind day.
    Light, compact, and easy to use, the F-One STRIKE CWC V3 is the quintessential light-wind weapon. Our patented 3-strut wing has proven to be the ideal concept for a successful large surface wing, and the STRIKE CWC has dominated light-wind wing foiling since its appearance on the market. Featuring a new and revolutionary design as well as F-ONE’s latest technologies and materials, this CWC V3 will let you show off your wing foiling skills in full confidence on any light wind day.
    F-ONE STRIKE CWC V3 WING
    F-One
    Save $719
    Recently viewed