Murrays Marine - Catamaran specialists

All

3135 products

    All Murrays Products: Hobie, Nacra, Prindle rigging, rudder parts, sails, trampolines, spare parts, lines and more. 

    3135 products
    Trampoline Slug Slide Murrays Part# 56-9892 Use for lacing tramp to rear crossbar to eliminate the need for an aft lacing strip. The slug can also be used in sail track. Used on the Hobie Getaway and Hobie 21SC forward trampolines Hobie Part # 96280000
    NACRA TRAMPOLINE SLUG SLIDE
    NACRA
    GATH helmet GOPRO MOUNT W/FASTENER
    GOPRO MOUNT WITH FASTENER
    Gath
    Cat Paws Hull Pads Murrays PN 13-0031 Cat Paws Hull Pads are foam pads that will protect your catamaran hulls. Similar to hull chocks, but much more versatile. Cat Paws can be used as a mast cradle while trailering, and are perfect for turning your cat on its side in parking lots.  Made from a highly durable closed cell foam that does not absorb water, mold or corrode. Ideal for use on Hobie, Nacra, and Prindle catamarans. Closed cell foam body with a bungee strap for holding it in
    Hobie hull chocks, Nacra hull pads
    CAT PAWS HULL PADS (2)
    Murrays Sports
    Hobie Pre EZ Loc Upper Pintle Murrays Part# 50-38101301 Replacement upper pintle assembly for Hobie Wave and Hobie Getaway sailboats using the pre EZ loc style rudder assembly. Original Equipment on Hobie Wave and Hobie Getaway sailboats Upper pintle should be mounted with two (2) screws Use Part# 8030171 for boats 2008 and older, or Part# 8030331 for 2009 and newer If you have an EZ Loc style assembly, use the Hobie EZ loc upper pintle part# 90880211 Hobie Cat Part # 38101301
    HOBIE WAVE/GETAWAY UPPER PINTLE - PRE EZ LOC
    Hobie
    Out of Stock
    104" Hobie batten part number 21000001
    H-16 MAINSAIL FIBERGLASS BATTEN 107"
    Murrays Sports
    Black Mast Caution Decal Murrays Part# 50-13440000 The Decal Mast Caution Black Hobie® factory caution decal attaches to mast as a reminder to watch for overhead power lines when sailing and/or launching your boat.
    BLACK MAST CAUTION DECAL
    Hobie
    O'Pen Skiff Rudder Mount Bottom Murrays Part# 65-53269 Lower stainless steel needle Tahe Part# 53269
    O'PEN SKIFF RUDDER MOUNT BOTTOM
    Tahe Outdoors
    Hobie Bravo Batten Cap Murrays Part# 50-9101100 Hobie batten cap for round battens Sold individually
    BRAVO BATTEN CAP
    Hobie
    H18 Wing Strut Tab Murrays Part# 50-65100000 Hobie® factory replacement wing strut tab for Hobie 18.
    H-18 WING STRUT TAB
    Hobie
    Selma_fid-kit x4 4.5mm-10mm
    SELMA ROPE SPLICE FIDS x4
    Selma
    Re-Dek Traction System Murrays Part# 40-2010 Re-Dek is a quick and easy way to obtain permanent, professional-quality traction. The kit provides an easy step application process that allows you to customize the areas where permanent, no-slip traction is needed. Re-Dek can be applied right over graphics and artwork without hiding or distorting them.
    RE-DEK TRACTION SYSTEM
    Misc
    Nut Low Profile 5/16-24 Nylock Murrays Part# 50-8050341 Hobie® factory replacement 5/16-24 low-profile nylock nut. Used in Hobie 18SX wings mounting bar kit (#50-65071001). Hobie Part# 8050341
    NUT LOW PROFILE 5/16-24" NYLOCK
    Hobie
    Hobie Tendon Kit (Pre EZ Loc) Murrays Part# 50-37561011 This tendon kit is the replacement for tendons used on the Hobie Wave, Hobie Getaway, and Hobie Bravo with the first generation EZ Loc rudders. This upgraded version is a notable improvement over the original tendons. Hobie Part# 37561011
    HOBIE TENDON KIT (PRE EZ LOC)
    Hobie
    H-16 JIB BATTEN 67" 67" Murrays jib batten with a trentec batten cap. Batten #1 in a Hobie 16 jib batten set - 20400001
    H-16 JIB FIBERGLASS BATTEN 67"
    Murrays Sports
    Sale
    SAFETY HOOK KNIFE FORWARD Murrays Part# 47-0700-2 Forward Hook Safety Knife, can be used in conjunction with the Forward Impact Vest. The Forward impact vest has a special pocket inside the webbing sleeve to store a Forward Hook Safety Knife.
    FORWARD SAFETY HOOK KNIFE
    Forward Wip
    Save $4
    #4 Spur Grommets Set of 24
    GROMMET #4 SPUR Set of 24
    Misc
    SMALL BLOCK W/REMOVABLE SHEAVE This small block is used on trapeze adjustment systems where the removable sheave enables installation without cutting wires. Specifications: 1-3/16" removable sheave, Teflon® bearing and 5/16" line capacity. Hobie item #3103
    SMALL BLOCK W/REMOVABLE SHEAVE This small block is used on trapeze adjustment systems where the removable sheave enables installation without cutting wires. Specifications: 1-3/16" removable sheave, Teflon® bearing and 5/16" line capacity. Hobie item #3103
    SMALL BLOCK WITH REMOVABLE SHEAVE
    Murrays Sports
    Replaceable Aluminum Trap Handle Murrays Part# 007-2010 Foam-covered aluminum handle is easily installed onto existing trapeze wire. Carry a spare as a temporary repair, then replace the wire at your convenience. Each. Hobie Cat® Part# 2010
    REPLACABLE ALUMINUM TRAP HANDLE
    Murrays Sports
    Prindle 18 Shroud 5/32" Black Wire Roller Swaged Murrays Part# 002-2305-12 One single black shroud (sidestay) for Prindle 18 is constructed to factory specifications. Hydraulic swaging produces a cleaner, stronger shroud.
    PRINDLE 18 SHROUD 5/32" BLACK WIRE ROLLER SWAGED
    Murrays Sports
    Oxen self-holding blocks offer a real advantage over blocks with cleats! Get fast, simple mainsheet (and jibsheet) control: just pull-to-cleat, then pull-to release! Cleat or uncleat your jib or mainsheet every time without looking and from any position. Cleat from any angle or position on the boat, including the wings, even if your sheet passes over something en route. Oxen blocks are easy to install and foolproof to use.
    Oxen block with becket - Hobie, Nacra, Prindle, jib sheet, main sheet
    3" OXEN BLOCK WITH PIN & BECKET
    Oxen
    Harken 6mm Stamped Shackle Murrays Part# 28-0138 Harken's stainless stamped D-shackle has 1/4" diameter pin. For Harken 3.00" blocks. Stamped shackles are used on most Harken Small Boat Blocks and are appropriate for low loads. For higher loads, select forged and high-resistance shackles instead.
    HARKEN 6MM STAMPED SHACKLE
    Harken
    Out of Stock
    Harken 57mm Carbo 10:1 System Murrays Part# 28-101 This system offers 10:1 purchase power! Light weight, low profile and very strong, these Carbo AirBlocks® have enormous working range, with a higher working load than standard blocks, even though they are lighter in weight. The base block has an on-off ratchet and will roll freely in both directions when disengaged, such as in light air. Engage the ratchet in heavy air when you need the mechanical advantage of the ratchet.
    HARKEN 57mm CARBO 10:1 SYSTEM
    Harken
    Out of Stock
    HOBIE HALYARD GRIP KIT The Hobie Halyard grip kit is a mast hook that hold the jib halyard off center on the mast so that the jib battens don't hang up on the jib halyard when tacking. Mostly used on the Hobie 16. Hobie part number 114
    HOBIE HALYARD GRIP KIT
    Hobie
    H20 Forestay Roller Furling 5/32" Black Wire Murrays Part# 002-0745-32 Lower forestay for Hobie® 20 with roller furling setup. Constructed to factory specifications.  Compare to Hobie Cat® Part# 48814001
    H-20 FORESTAY ROLLER FURLING 5/32" BLACK WIRE
    Murrays Sports
    H18SX Jib Halyard with Shackle Murrays Part# 002-0686-00 Jib halyard with shackle for Hobie® 18SX is constructed to factory specifications.; Use 20' of 1/8" line to to complete your jib halyard or our jib halyard kit with sister clips. links below in related items. Compare to Hobie Cat® Part# 68661001
    H-18SX JIB HALYARD WITH SHACKLE
    Murrays Sports
    3/16 X 1-1/4" Clevis Pin Murrays Part# 22-9807 Stainless steel clevis pin. Measurement is 3/16" diameter x 1-1/4" grip length (shoulder to the split ring hole). Can replace Hobie Part# 8020340 Hobie Wave Mast Head Sheave Pin
    CLEVIS PIN 3/16 X 1-1/4
    Misc
    Cat Trax Tire Only 21x12 Murrays Part# 13-1401-3 Replacement 21″x12.0-8 tire only (without rim) for Cat Trax beach wheels.
    CAT TRAX TIRE ONLY 21X12
    Cat Trax
    he comfortable, 6" adjustable foot straps feature 7mm neoprene padding to comfortably accommodate bare feet or sailing shoes. Their pre-formed arch eliminates collapsing and the exterior hook and loop closure system allows for quick and easy adjustment. Drilling instructions and self-tapping screws are included.
    DAKINE CATAMARAN FOOTSTRAP KIT (PR)
    Dakine
    Cat Righter Uphaul: Cam-Clt 4:1 Murrays Part# 001-3273 This is the 4:1 block and tackle system only from Murrays' popular Cat Righting Big Bag System (#01-3280). Use with a righting bag to aid in righting a capsized catamaran.
    CAT RIGHTER UPHAUL: CAM-CLEAT 4:1
    Murrays Sports
    Cat Bag 4" Murrays Part# 001-1169 The Cat Bag provides handy storage inside a deck port! The sturdy nylon bag with plastic collars hangs inside 4" access port on a molded shoulder. 12" deep. Hobie Cat® uses #5402 for this item.
    4" PORT CAT BAG
    Sea Dog
    3-Hole Pad Kit Murrays Part# 001-0110 This base kit is for Harken®, Hobie® or Murray 360 cleats without swivel base adapters. Kit includes one 3-hole base, one swivel base adapter (#25-3001), plus three #10 FHSMS (#19-1626). Ronstan swivel 360 cleats include swivel base adapters, so this kit is not necessary. Fits Hobie® or Prindle elliptical crossbar.
    3-HOLE PAD KIT
    Murrays Sports
    1/2 BALL (NYLON) - Hobie half round washer spacer tiller connector - Hobie part number 11510000 HOBIE HALF SPHERE TILLER CONNECTOR
    Tiller Connection Kit Murrays Part# 001-2061 The Murrays Tiller Connection Kit assures consistent rudder alignment through the full rudder sweep. Spring-loaded half balls and contoured spacers take the slop out of the tiller-to-crossbar connection on Hobie Cats. Racing class legal. Each kit contains 2 connectors to join the tiller crossbar to the tiller arms. Compare to Hobie Cat® #3052. Applications:; Hobie 14, 16, 17, 18, 18SX
    NYLON 1/2" BALL
    Murrays Sports
    HOBIE EPO3 RUDDER BLADE
    Hobie
    H16 Jib Sail (White) Murrays Part# 50-20992010 This is an OEM Hobie White Jib for the Hobie 16 sailboat. This is class legal for One Design Hobie Racing. This sail includes batten ties
    H-16 JIB SAIL (WHITE)
    Hobie
    Wave 4:1 Main Sheet System Murrays Part# 28-041 The Murrays Hobie low profile 4:1 main sheet system for the Hobie Wave. By Adding a fairlead to the back side of the cleat on the base block we have made a low profile main sheet system that no longer needs a becket on the base block. We have also replaced the upper fiddle block with a double block which makes it even more compact. The result is a lightweight, low profile and very strong, made with 40mm Harken Carbo AirBlocks.
    Murrays low profile Hobie 14 main sheet system
    WAVE 4:1 MAIN SHEET SYSTEM
    Murrays Sports
    Harken Standard Carbo-Cam Cleat Murrays Part# 28-0365 Harken Cam-Matic® ball bearing cam cleats engage and release easily, hold securely, and work with a wide range of line types and sizes. Cam teeth are smooth to protect line and because tooth grip is not required to close the pawls. Multiple rows of UV-stabilized, Delrin® ball bearings provide minimal friction for easy line engagement and release, even under high loads.
    HARKEN STANDARD CARBO-CAM CLEAT
    Harken
    1/4" QUICK RELEASE BOW SHACKLE
    Murrays Sports
    Hobie 16 Grey Mesh Trampoline OEM - Hobie Part #20970058
    H-16 MESH TRAMPOLINE-GREY
    Hobie
    Nacra Rear Beam Tramp Tie Buttons Murrays Part# 56-30883 The NACRA Rear Beam Tramp Tie Buttons are the black nubs that are riveted on to the rear beam to hook the tramp lacing around. These are used on many boats and are installed with a 3/16 1/2" rivet. These can likely also be used on a Hobie Getaway, Miracle 20 or others that are looking to use a smaller Dyneema line instead of the 3/16 or 5/32 line Nacra Part# 30883
    NACRA REAR BEAM TRAMPOLINE TIE BUTTONS
    NACRA
    Out of Stock
    Swivel Cam Cleat Pad Murrays Part# 50-11900010 Replacement base pad for your H16 jib car cleats or Mainsheet on most Hobie Cat sailboats. Hobie Part# 11900010
    SWIVEL CAM CLEAT PAD
    Hobie
    Recently viewed