Murrays Marine - Catamaran specialists

All

3135 products

    All Murrays Products: Hobie, Nacra, Prindle rigging, rudder parts, sails, trampolines, spare parts, lines and more. 

    3135 products
    H-18/21SC UPPER FORESTAY 5/32" WIRE
    Murrays Sports
    This harness has been reimagined, redesigned, and rigorously tested by the Rooster team to provide the ideal amount of support and comfort on the Trapeze. The curved and pre-shaped body can be adjusted at 3 points on each side to allow adjustment down the upper back, across the middle, and up from the seat panel, to tailor the fit to different shapes.
    ROOSTER TRAPEZE HARNESS Nappy Style
    Rooster
    Quick-Release Pin Detent 1/4 X 1-1/2 Murrays Part# 18-4D150 The Quick-Release Pin Detent 1/4 X 1-1/2 is an economical, quick connection for Hobie 16 mast step pin. A spring-loaded ball exerts sufficient pressure to help avoid accidental release. Measurements are 1/4″ diameter x 1-1/2″ maximum grip length (distance from the shoulder to the locking ball bearings).
    QUICK RELEASE DETENT PIN 1/4 X 1-1/2"
    Misc
    HARKEN 6MM BOW SHACKLE
    Harken
    CINCH RINGS - Stainless Steel SOLD EACH
    MISC
    Rudder Casting Lock Spring Murray Part# 50-10430000 Hobie factory replacement 2-1/8" lock spring for rudder casting. Replace rudder springs with this original spring supplied on Hobie® 14, 16, (pre 1983) 17 and 18. Compare to HC part number 10430000 H14, H16, H17, H18, H20
    HOBIE RUDDER SPRING
    Hobie
    H18 Mast Head/Base Sheave Murrays Part# 50-60620000 Factory replacement sheave for Hobie 18 mast head/base and outhaul assembly. Specs: 1" Diameter x 3/8" wide and 1/4" hole. Also used as traveler control line turning sheave on 2005 and newer Hobie 16 sailboats. Applications: Hobie 18 - Mast head halyard sheave ; mast base halyard sheave ; outhaul car sheaves. Hobie 16 - Jib Traveler line sheave. (in the H16 Race Corner Castings) use 50-8011251 Rivet
    H-18 MAST HEAD/BASE SHEAVE
    Hobie
    Rudder Cam Screws H17, H18, H20, Older Wave and Getaway Murrays Part# 001-3551 The Murrays Rudder Cam Pins are a pair of sister screws for use on the Hobie 17, 18, 20, 21, as well as the older Hobie Wave and Getaway rudder cams. These pins are an upgrade form the original stock hollow flare rivet that came on the Hobie. The Sister Screws are much easier to install and remove, and they are reusable. Compare to Hobie Cat® #5203 and #50312301. Sold in pairs
    H-17/18/20/OLDER WAVE AND GETAWAY RUDDER CAM PINS
    Murrays Sports
    Quick Release Detent Pin 1/4 X 3" Murrays Part# 18-4D300 Economical quick release pin has a spring-loaded ball that exerts sufficient pressure to help avoid accidental release. Measurements are 1/4" diameter x 3" maximum grip length (distance from the shoulder to the locking ball bearings). Uses: - Use as mast step pin on Hobie® 21 and Prindle 16/18/18-2/19 cats. Compare to Hobie part # 8020501
    Quick Release Detent Pin 1/4 X 3" Murrays Part# 18-4D300 Economical quick release pin has a spring-loaded ball that exerts sufficient pressure to help avoid accidental release. Measurements are 1/4" diameter x 3" maximum grip length (distance from the shoulder to the locking ball bearings). Uses: - Use as mast step pin on Hobie® 21 and Prindle 16/18/18-2/19 cats. Compare to Hobie part # 8020501
    QUICK RELEASE DETENT PIN 1/4 X 3"
    Misc
    Quick Release Pin Deluxe  3/16 X 3/4" Murrays Part# 18-3M075 This Quick Release Pin features 2 locking balls for a extra secure grip, and a push button deluxe dished head with a hole for lanyard attachment. The Deluxe pin is quick and easy to remove and install, and makes getting on and off the water quicker and easier.
    QUICK RELEASE PIN DELUXE 3/16 X 3/4"
    Misc
    clevis pins with split rings for the standing rig and mast stepping systems of Hobie 17, Hobie 20, or Nacra. Kit includes 18 pieces: mast hinge pin, clevis pin assortment, and split ring assortment.  Compare to Hobie Cat #30317.
    H-17/20/NACRA PINS AND RINGS KIT
    Murrays Sports
    H-16 UPPER FORESTAY 5/32 BARE Murrays PN 002-0235-00 Upper forestay for The Hobie® 16 is constructed of 7x19 - 5/32" bare wire to factory specifications. Compare to Hobie Cat® #20810011. This part is used as part of the classic halyard/ forestay configuration and it holds the stainless pulley that the jib halyard cable attaches to. This will also work to hold your Aussie halyard block assembly.
    Hobie 16 forestay and jib halyard parts chart
    H-16 UPPER FORESTAY 5/32" BARE WIRE
    Murrays Sports
    H16 Jib Halyard with Shackle Murrays Part# 002-0284-00 Jib halyard with shackle for Hobie 16 is constructed to factory specifications. This is for use on the classic style H16 jib halyard system with a metal sheave up near the mast tang that was standard in the 70s and 80s. The rope section of the jib halyard is 20' of 3/16ths line. Compare to Hobie Part# 20661001
    Hobie 16 forestay and jib halyard parts chart
    H-16 JIB HALYARD WITH SHACKLE
    Murrays Sports
    The Aussie forestay replaced the original upper and lower forestay system in 2009 on the Hobie 16 as the factory standard. It is modeled after what the dominant Aussie racers using on their boats. Aussie forestays are longer than the classic halyard forestays actually have a separate connection cable for the jib halyard. The separate attachment point for the jib halyard provides a back up if either were to fail. If either the forestay or jib halyard were to break, the other will hold the m
    H-16 AUSSIE FORESTAY
    Murrays Sports
    Out of Stock
    Starboard-Lance Cleat Murrays Part# 007-359S The Lance Cleat - Starboard utilizes a single rugged aluminum alloy cam mounted vertically in a black molded frame. The rope slides in sideways and runs freely thru the fairlead, which has a colored roller incorporated in the top for easier sheeting and identification. Ideal for use in confined spaces. For use with 3/16 to 1/4″ line. The base is 22mm x 30mm.
    STARBOARD-LANCE CLEAT
    RWO
    Murrays Original Hobie 14 & 16 Jib traveler car for pre 1994 boats with the external track on the front crossbar. 21230000
    MURRAYS H-14/16 JIB TRAVELER CAR
    Murrays Sports
    Screw Delrin 3/8-16 X .75" Murrays Part# 50-8032001 Hobie® factory replacement 3/8-16 x 3/4" Delrin screw is used as rudder rake adjustment screw on Pre-EZ Lock Rudder System. Hobie Part# 8032001
    SCREW DELRIN 3/8-16 X .75"
    Hobie
    Wave Mainsheet S Hook Murrays Part# 50-38900031 Hobie® factory replacement S-hook for Wave mainsheet. Mainsheet is 35 feet of Dacron® spun braid #39-055. Makes it easy to attach mainsheet to sail and standard on all new boats. Hobie Part# 38900031
    WAVE MAINSTEET S HOOK
    Hobie
    EZ Lock Upper Pintle Murrays Part# 50-90880211 Hobie® factory replacement upper pintle for EZ Loc rudder system. Fits Hobie Bravo and Getaway boats Hobie Part# 90880211
    BRAVO/WAVE/GETAWAY EZ LOC UPPER PINTLE
    Hobie
    Batten Cap Jib Leech H16 Murrays Part# 50-2133000 Hobie® factory jib leech batten cap for Hobie® 16. For batten tie, use 18" of 1/8" Dacron® solid braid #39-0221. These are also used on the top two battens of a Hobie Wave and the top batten of a Hobie 18 Mainsail. Sold individually
    HOBIE JIB BATTEN LEECH CAP (EA)
    Hobie
    Rudder Return Kit for H14/16-Inter Murrays Part# 012-2049 This Rudder Return Kit for H14/16-Inter by Tren Tec eliminates kick-up. Rudders return to down position easily with one hand and tension holds rudder down if a cam fails. Accommodates both rudders. Use this page to order product numbers 12-2049 (for Hobie® 14/16/Inter; Hobie Cat® item #1544)) and 12-2059 (for Hobie 17/18/21)
    H-14/16 INTER RUDDER RETURN KIT
    Tren-Tec
    Rivet CCC 6-6 (3/16 X 3/8) Countersunk Murrays Part# 19-5024 Countersunk stainless steel 3/16" x 3/8" rivet for traveler tracks, etc. Compare to Hobie Part # 8010201. This rivets is what Hobie recommends for both the main traveler tack and the jib traveler track. We also recommend using an 1/8" stop sleeve, part number 002-1041, as a spacer to help you apply pressure on the rivet inside the track, as the track is too narrow for most rivet guns to get far enough inside to apply pressure to the rivet.
    RIVET CCC 6-6 CSK
    Misc
    Hobie 18 forestay - Hobie part number 60810021 white or 60812021 black
    H-18/21SC FORESTAY 5/32" WIRE
    Murrays Sports
    Getaway Trapeze Wire (2 Handles) Murrays Part# 002-0953-02 The Murrays Getaway Trapeze is a set of 2 black or white coated trap wires with 2 handles for trapezing. Order shock cord, harness loops and adjustment kits separately.
    GETAWAY TRAPEZE BLACK WIRE (2)
    Murrays Sports
    Dacron 3oz Sail Tape-White Murrays Part# 010-3430 Quickly mend tears in Dacron sails, covers, rain gear and seats. The heavy-duty, 3-oz. Dacron sailcloth makes long-lasting emergency repairs or provides effective reinforcement for worn areas. Features quick marine adhesive backing; can be stitched for permanent repair. Our white Dacron sail repair tape is 3" x 15'.
    DACRON 3OZ MAINSAIL TAPE-WHITE
    Bainbridge
    Out of Stock
    H16 Angled Luff Caps Murrays Part# 012-3005 No more battens poking through next to the mast! Tren Tec luff batten caps for Hobie® 16 main sail prevent batten splitting and align batten to the angle of the sail. Glue cap to the forward end of the batten. Hobie Part# 1562 Sold in packages of 8
    H-16 ANGLED LUFF CAPS (8)
    Tren-Tec
    Batten Cap Leech H14/16/17/18 Main E Murrays Part# 012-3003-1 No more knots at the trailing edge. Adjust sail shape in seconds without tying and untying knots. Release tension to prolong sail shape and life. Individual batten cap for Hobie 14, 16, 17 or 18 main sail. Mainsail batten cap for Saturn shape main sail battens used on Hobie, Prindle some Nacra sails. Trentec part number BC-HM Compare to Hobie 11323000 Sold individually 
    H-14/16/17/18 MAIN BATTEN LEECH CAP
    Tren-Tec
    Hobie 16 Rigging Set 2009 Spec All parts needed for 2021 Race Ready Boat! If you're trying to update your old boat or just need new rigging for your late model Hobie 16, this is the complete package. Whether your racing or just putting around the lake, this kit is accommodates the current rigging standard for factory sails and production boats. All of our rigging is made from 316 stainless steel wire. Thimbles are swaged using our custom hydraulic swaging machine for years of reliable service.
    H-16 RIGGING SET 2009 SPEC
    Murrays Sports
    HOBIE 16 MAINSAIL BATTEN CAP KIT - LEACH - 1522H
    H-16 MAINSAIL BATTEN LEACH CAP KIT (8)
    Hobie
    Magic Marine Quick Release Spreader Bar The Magic Marine quick release spreader bar features a quick release sacrificial hook for safety and peace of mind while sailing. The hook can be detached with a simple pull of the quick release pin in an emergency situation. The hook can also be purchased separately, please see Item 34-1199.
    MAGIC MARINE QUICK RELEASE SPREADER BAR
    Magic Marine
    Rudder Locking Bolt Murrays Part# 56-4017 The Prindle Rudder Locking Bolt is the factory replacement bolt for rudder locking system on all Prindles. Tip: Be sure to check for proper alignment of the lock bolt to spring bolt. Any bent component will prevent the system from working properly. Identify and replace the bent portion to get your rudder system functioning properly. Performance Sports factory item# 4017
    PRINDLE RUDDER LOCKING BOLT
    NACRA
    MURRAYS HOBIE 20 DRAIN PLUG
    MURRAYS H-20 DRAIN PLUG
    Murrays Sports
    Hobie 20-style factory tiller connector post. Part of the Hobie 1953 tiller connection system. Hobie part number 40530000 and 40530001
    Hobie 1953 tiller connection kit - new style
    H-20 TILLER CONNECTOR POST
    Hobie
    Hobie Rudder Covers Murrays PN 50-82420000 Rudder covers by Hobie protect your rudders from nicks and grime. Hobie's rudder covers feature straps with Fastex® fasteners to keep the covers firmly in place, even when trailering. The covers fit all Hobies except H21SE (Special Edition). These come as a pair. Hobie part number 82420000
    HOBIE RUDDER COVER
    Hobie
    Mast Base Casting Murrays Part# 56-6005 Mast base casting for Prindle 16 Nacra Sailing factory item# 30442
    PRINDLE 16 MAST BASE CASTING
    NACRA
    Harken Swivel with Carbo Cam Bullseye Murrays Part# 25-3010 Swivel cam cleats are ideal for main traveler control and up-release jib cleating systems. Cam cleats and fairleads should be selected on the basis of need. Order plastic base pads and flat head screws separately to mount to your front crossbar.
    HEAVY DUTY SWIVEL WITH CARBO CAM & BULLSEYE
    Murrays Sports
    H14/16 Aluminum Rudder Pins Murrays Part# 001-2272 Aluminum rudder pins are standard on Hobie® 14 and 16 and are good for all-around, low maintenance use. Pair of 3/8" x 8" rudder pins with cotter pins. New One piece rudder gudgeons have been produced with a slightly smaller metric hole size. If you have a 2020 and newer boat or 2020 and newer one piece gudgeons, our aluminum rudder pins may require force to install and be difficult to remove. The stainless pins are a better fit. Sold in pairs
    H-14/16 ALUMINUM RUDDER PINS
    Murrays Sports
    Replace a 3/16" bow shackle with this quick-release version to add convenience. Can be used on 2-1/4" blocks. Compare to Hobie Cat® #3062.
    QUICK RELEASE 3/16" BOW SHACKLE
    Murrays Sports
    Hobie 18 clevis pin kit includes 13 pieces: mast hinge pin, clevis pin assortment, and split ring assortment. Compare to Hobie Part Number #30304 Murrays.com
    H-18 PINS & RINGS KIT
    Murrays Sports
    Hull Cradle: Universal Murrays Part# 13-7010
    HULL CRADLE: UNIVERSAL
    Murrays Sports
    Recently viewed