Murrays Marine - Catamaran specialists

All

3154 products

    All Murrays Products: Hobie, Nacra, Prindle rigging, rudder parts, sails, trampolines, spare parts, lines and more. 

    3154 products
    H16 Aussie Jib Halyard Kit with Pigtail Murrays Part# 001-3302 Reduce mast compression by 66%! The Aussie Jib Halyard Kit for the Hobie® 16 allows easier tacking, better mast rotation and consistent mast bend! Use with existing lower forestay. The "fail-safe" pigtail keeps block failure from resulting in de-masting. A similar system is stock on new Hobie® 16's. Complete kit includes everything you need: hardware with all Harken blocks, 70' of prestretched line, zippered pouch and instructions.
    H-16 AUSSIE JIB HALYARD KIT WITH PIGTAIL
    Murrays Sports
    Getaway Shroud 5/32" Black Wire Murrays Part# 002-0905-02 Single black shroud (sidestay) for Hobie® Getaway is constructed to factory specifications. Compare to Hobie Cat® Part# 37790001
    GETAWAY SHROUD 5/32" BLACK WIRE
    Murrays Sports
    Cat Trax Tire Tubes Murrays Part# 13-1401-9 Add an inner tube to the tire(s) of your Cat Trax beach dolly to prevent air leaks or squeeze some life out of your old tires. Sold individually
    CAT TRAX TIRE TUBE
    Cat Trax
    GATH GEDI HALF VISOR
    Gath
    9/32" RACING PRO 7MM
    Robline
    CAT TRAX CRADLES (PAIR)
    Cat Trax
    Prindle 18/19 Ronstan Mast Head Base Sheave Murrays Part# 56-6804 Replacement sheave for mast base on Prindle 15, 18, 18.2, 19 and Nacra 2003 and later mast head. Sheave measures 1-1/8" diameter x 3/8" wide. Please note that this item replaces #6803 that is no longer available.
    PRINDLE 18/19 RONSTAN MAST HEAD SHEAVE
    Ronstan
    The Murrays Hobie 16 one piece rudder gudgeon is not cast but machined and then anodized for superior strength and longevity. Compare to Hobie 50102011
    The Murrays Hobie 16 one piece rudder gudgeon is not cast but machined and then anodized for superior strength and longevity. Compare to Hobie 50102011
    MURRAYS H-16 ONE PIECE RUDDER GUDGEON
    Murrays Sports
    Wave Forestay 1/8" Black Murrays Part# 002-0844-02 One black forestay for Hobie® Wave is constructed to factory specifications. Compare to Hobie Cat® #39810001.
    WAVE FORESTAY 1/8" BLACK WIRE
    Murrays Sports
    The Murrays Trapeze handle features a contoured grip and a wire guide prevent hand contact with the wire. A recessed cavity in the base holds the nicropress oval and shields the sailor from sharp wire ends. Sold Individually. Hobie uses item #2011 for this handle. Used on Nacra, Prindle and Hobie catamarans.
    MURRAYS TRAPEZE HANDLE
    Murrays Sports
    O-Ring: 6" Screw-In Port Murrays Part# 001-4210OR ​Replacement “O” ring for 6″ port (hatch) #01-4210. Viking, Sea Dog
    O-RING: 6" SCREW-IN PORT
    MISC
    Jib Traveler Cars for Original Track Murrays Part# 012-3020 Tren Tec's black plastic cars have four holes and slide freely in the track. Low profile shape saves needed space when mast is raked to the extreme. For 1996 and earlier Hobie 16s with external track that is riveted to the crossbar. Sold as a Pair. Hobie part number 1552 Sold in pairs
    JIB TRAVELER CARS (PAIR)
    Tren-Tec
    The Murrays Jib Snorkel will protect your roller furling jib from ultraviolet light and weather while on or off the boat.
    MURRAYS JIB SNORKEL
    Murrays Sports
    Hobie 18 mast step hinge pin, has a hole on one end only. The headless clevis pin measures 1/4″ diameter by 3-3/8″ grip length Hobie Part # 8020501
    HEADLESS CLEVIS PIN 1/4 X 3-3/8"
    Misc
    Out of Stock
    Port-Lance Cleat Murrays Part# 007-359P The Lance Cleat - Port utilizes a single rugged aluminum alloy cam mounted vertically in a black molded frame. The rope slides in sideways and runs freely thru the fairlead, which has a colored roller incorporated in the top for easier sheeting and identification. Ideal for use in confined spaces. For use with 3/16 to 1/4" line. The base is 22mm x 30mm.
    PORT-LANCE CLEAT
    RWO
    Wave Bridle 1/8" Black Murrays Part# 002-0814-02 One black bridle for Hobie® Wave is constructed to factory specifications. Compare to Hobie Cat® 39822011.
    WAVE BRIDLE 1/8" BLACK WIRE
    Murrays Sports
    Snap Shackle With Tack 1/4" Murrays Part# 22-4501 Swiveling tack shackle with 1/4" clevis pin. Use on hexaratchets on Hobie® 18, Nacra or Prindle. To connect the swivel shackle to an item that requires a 3/16" clevis pin, you will need a 3/16" clevis pin with 7/8" shaft. Also convenient for the jib tack connection on Nacras and Inters.
    SNAP SHACKLE WITH TACK 1/4"
    Murrays Sports
    Murrays red, green and blue tell tails. Sail trimming guides.
    MURRAYS TELL TAIL SET
    Murrays Sports
    Micro D-Splicer Splicing Needle Murrays Extra Small Line Splicer for 1-2mm line The Murrays Extra Small Line Splicer for 1-2mm line is designed to splice really small diameter lines.  It is ideal for making kiteboarding line sets. Material: 316 stainless wire and a copper/nickel end stop Length: 6"
    MICRO D-SPLICER SPLICING NEEDLE
    Murrays Sports
    HOBIE 14/16 GOOSENECK ASSEMBLY Murrays PN 50-10770001 Hobie factory replacement gooseneck assembly for Hobie 14 or 16. Hobie Cat item #10770001.
    H-14/16 GOOSENECK ASSEMBLY
    Hobie
    Murrays Part# 007-1051 The standard replacement deck plate for the traveler on all Hobie® 14, 16 and newer 17's. Hobie Cat® factory item #11870000.  Uses a 3/16 x 1/2" clevis pin to attach to the main sheet system. Also used in Hobie 14 and Hobie 16 upgrade downhaul systems to secure lower block. Sold individually
    TRACKER DECK PLATE (EA)
    Hobie
    Rivet CCP 6-8 (3/16 X 1/2) Murrays Part# 19-5033 Stainless steel 3/16" x 1/2" rounded pan head rivet. Compare to Hobie Cat® #8011231.
    RIVET CCP 6-8 (3/16 X 1/2)
    Misc
    H-18/21SC UPPER FORESTAY 5/32" WIRE
    Murrays Sports
    H16 Jib Halyard with Shackle Murrays Part# 002-0284-00 Jib halyard with shackle for Hobie 16 is constructed to factory specifications. This is for use on the classic style H16 jib halyard system with a metal sheave up near the mast tang that was standard in the 70s and 80s. The rope section of the jib halyard is 20' of 3/16ths line. Compare to Hobie Part# 20661001
    Hobie 16 forestay and jib halyard parts chart
    H-16 JIB HALYARD WITH SHACKLE
    Murrays Sports
    The Hobie 16 Main sheet Pro is 9mm Ronstan Robline Racing Sheet Pro which lighter and more flexible than the standard main sheet line. It flows thru the blocks quicker and is made with super strong Dyneema fiber for ultimate strength and anti stretch properties with added Taslan for improved grip and cleating. Racing Sheet Pro is soft in the hand and cleats superbly. Amazing in light air as it flows itself thru the blocks with less drag allowing the sails to go out on their own in less wind. Lighter, strong
    H-16 MAIN SHEET PRO
    Robline
    Hobie 16 One Piece Gudgeon Upper and Lower Bushing Insert - 50102010
    H-16 ONE PIECE GUDGEON UPPER AND LOWER BUSHING INSERT
    Hobie
    Prindle split rings and clevis pin kit, mast hinge pin
    PRINDLE PINS & RINGS KIT
    Murrays Sports
    CINCH RINGS - Stainless Steel SOLD EACH
    MISC
    H18 Traveler Cylinder Bearing Set Murrays Part# 50-61852000 Hobie® factory replacement cylinder bearing set for Hobie® 18 main traveler. Set includes one pair.
    Hobie 18 main traveler car parts list - 6180001, 8040301, 61870000, 61880000, 60190000, 8050311, 61842000, 8060121, 61810000, 61830000, 61852000, 8020431
    H-18 TRAVELER CYLINDER BEARING SET
    Hobie
    H18 Mast Head/Base Sheave Murrays Part# 50-60620000 Factory replacement sheave for Hobie 18 mast head/base and outhaul assembly. Specs: 1" Diameter x 3/8" wide and 1/4" hole. Also used as traveler control line turning sheave on 2005 and newer Hobie 16 sailboats. Applications: Hobie 18 - Mast head halyard sheave ; mast base halyard sheave ; outhaul car sheaves. Hobie 16 - Jib Traveler line sheave. (in the H16 Race Corner Castings) use 50-8011251 Rivet
    H-18 MAST HEAD/BASE SHEAVE
    Hobie
    Quick Release Pin Deluxe  3/16 X 3/4" Murrays Part# 18-3M075 This Quick Release Pin features 2 locking balls for a extra secure grip, and a push button deluxe dished head with a hole for lanyard attachment. The Deluxe pin is quick and easy to remove and install, and makes getting on and off the water quicker and easier.
    QUICK RELEASE PIN DELUXE 3/16 X 3/4"
    Misc
    Quick Release Deluxe Pin 1/4 X 1.5 with Lanyard Murrays Part# 18-4M150L This quick release pin features a push button on the top that releases 2 spring-loaded balls at the tip that secure the pin in place. This pin includes a lanyard to help prevent loss of pin. Uses: Hobie 18 mast hinge pin, Compare to Hobie part#P 20307 PIN, QR 1/4 X 1-1/2 CUP Upgrade for Hobie 8020181, 8020180, 8020431, 8020430, 8020420, 8020421
    QUICK RELEASE DELUXE PIN 1/4 X 1-1/2" WITH LANYARD
    Misc
    clevis pins with split rings for the standing rig and mast stepping systems of Hobie 17, Hobie 20, or Nacra. Kit includes 18 pieces: mast hinge pin, clevis pin assortment, and split ring assortment.  Compare to Hobie Cat #30317.
    H-17/20/NACRA PINS AND RINGS KIT
    Murrays Sports
    Harken Standard Cam-Matic Cleat -150 Murrays Part# 28-0150 For high load/high-wear applications. Cam-Matic® ball bearing cam cleats engage and release easily, hold securely, and work with a wide range of line types and sizes. Cam teeth are smooth to protect line and because tooth grip is not required to close the pawls. Three rows of UV-stabilized, Delrin® ball bearings provide minimal friction for easy line engagement and release, even under high loads.
    HARKEN ALUMINUM CAM-MATIC CLEAT-150
    Harken
    H-16 UPPER FORESTAY 5/32 BARE Murrays PN 002-0235-00 Upper forestay for The Hobie® 16 is constructed of 7x19 - 5/32" bare wire to factory specifications. Compare to Hobie Cat® #20810011. This part is used as part of the classic halyard/ forestay configuration and it holds the stainless pulley that the jib halyard cable attaches to. This will also work to hold your Aussie halyard block assembly.
    Hobie 16 forestay and jib halyard parts chart
    H-16 UPPER FORESTAY 5/32" BARE WIRE
    Murrays Sports
    Ronstan Plastic Drain Plug with Chrome Brass Housing, 15/16" Hole Murrays Part# 21-0737 This lightweight and inexpensive plug features a molded recess in the base that traps sealant (sold separately) in place, providing a more watertight seal. Nylon plug is UV-stabilized. Retaining legs keep drain plug from falling out of hole when unscrewed. Includes chromed brass housing (body) and gasket.
    RONSTAN PLASTIC DRAIN PLUG WITH CHROME BRASS HOUSING, 15/16" HOLE
    Ronstan
    Batten Cap Leech H14/16/17/18 Main E Murrays Part# 012-3003-1 No more knots at the trailing edge. Adjust sail shape in seconds without tying and untying knots. Release tension to prolong sail shape and life. Individual batten cap for Hobie 14, 16, 17 or 18 main sail. Mainsail batten cap for Saturn shape main sail battens used on Hobie, Prindle some Nacra sails. Trentec part number BC-HM Compare to Hobie 11323000 Sold individually 
    H-14/16/17/18 MAIN BATTEN LEECH CAP
    Tren-Tec
    Black Gath Neo Surf Helmet
    Red Gath Neo Surf Helmet
    +2
    GATH NEO SPORT HELMET
    Gath
    Out of Stock
    Starboard-Lance Cleat Murrays Part# 007-359S The Lance Cleat - Starboard utilizes a single rugged aluminum alloy cam mounted vertically in a black molded frame. The rope slides in sideways and runs freely thru the fairlead, which has a colored roller incorporated in the top for easier sheeting and identification. Ideal for use in confined spaces. For use with 3/16 to 1/4″ line. The base is 22mm x 30mm.
    STARBOARD-LANCE CLEAT
    RWO
    Murrays Original Hobie 14 & 16 Jib traveler car for pre 1994 boats with the external track on the front crossbar. 21230000
    MURRAYS H-14/16 JIB TRAVELER CAR
    Murrays Sports
    Recently viewed