Hobie 14 Parts

230 products

    Parts to fit your Hobie 14

    230 products
    Stainless steel clevis pin. Measurement is 1/4" diameter x 5/8" grip length. Hobie part number 8020361, 8020381 and 8020380.
    CLEVIS PIN 1/4 X 5/8
    Misc
    Rivet CCC 6-6 (3/16 X 3/8) Countersunk Murrays Part# 19-5024 Countersunk stainless steel 3/16" x 3/8" rivet for traveler tracks, etc. Compare to Hobie Part # 8010201. This rivets is what Hobie recommends for both the main traveler tack and the jib traveler track. We also recommend using an 1/8" stop sleeve, part number 002-1041, as a spacer to help you apply pressure on the rivet inside the track, as the track is too narrow for most rivet guns to get far enough inside to apply pressure to the rivet.
    RIVET CCC 6-6 CSK
    Misc
    Out of Stock
    DECAL MAST CAUTION BLACK
    Hobie
    Decal Mast Caution Orange Murrays Part# 13440010 Hobie® factory decal attaches to mast as a reminder to watch for overhead power lines when sailing and/or launching your boat. Hobie Part# 13440010
    DECAL MAST CAUTION ORANGE
    Hobie
    Small Fairlead: 1-1/4 X 1/2 Murrays Part# 23-0921 Stainless steel fairlead measurements: A = 1-1/4" (31.4mm) between holes center-to-center B = 1/2" (12.7mm) height C = 3/16" (5mm) hole diameter
    RONSTAN SMALL FAIRLEAD: 1-1/4 X 1/2
    Ronstan
    Bolt Allen Head 5/16 18 X 1.5" (Stainless Steel) Murrays Part# 19-2229S Bolt Allen Head 5/16 - 18 X 1.5 (Stainless Steel) - replace hex head bolts used on Hobie 16, 17, 18, 20 Upper adjustable rudder castings. Limited space for Hex head requires thin walled 1/2" socket with 1/6" drive. Socket head bolt uses Allen head tool which is cheap, strong, and compact for on board storage and convenient adjustment.
    BOLT ALLEN HEAD 5/16-18 X 1.5" (SS)
    Misc
    Bolt Hex Head 5/16-18 X 1.5" Murrays Part# 19-2229 Use this stainless steel, 5/16-18 x 1-1/2" hex head bolt as beam strap bolt for Nacra. Substitute for Nacra Sailing factory item #30358. This bolt is also used to hold the cam stop plate on a Hobie Rudder Upper casting. Replaces Hobie Cat® Part# 8040301 and Murrays Part# 56-F164
    BOLT HEX HEAD 5/16-18 X 1.5"
    Misc
    Sealed Rivet CCP 6-8 (3/16 X 1/2) Murrays Part# 19-5033S Sealed rivets have a sealed end that does not require rivet casings to make them water tight. One and done, no casing needed, just insert and pop as you would a normal rivet, and your hole will be sealed. Sealed Stainless steel 3/16" x 1/2" rounded pan head rivet. Compare to Hobie Cat® #8011231 Rivet and Hobie Cat® #8011291 rivet casing.
    RIVET CCP SEALED 6-8 (3/16 X 1/2)
    Misc
    Gooseneck Boom Pin Murrays Part# 50-50502201 Hobie Cat gooseneck boom pin for securing boom assembly to mast at the gooseneck joint. Hobie Part# 50502201
    HOBIE GOOSENECK BOOM PIN
    Hobie
    Sealed Stainless Steel 3/16" x 3/8" Pan Head Rivet Murrays Part# 19-5032S Sealed rivets have a sealed end that does not require rivet casings to make them water tight. One and done, no casing needed, just insert and pop as you would a normal rivet, and your hole will be sealed. Among other uses, the Stainless steel 3/16" x 3/8" pan head rivet can be used when Hobie® rivet #8010131 is specified: Hobie 14 (2) or 16 (4) mast head Hobie Wave/Getaway/14/16/17/18/18SX/ mast base (4) Hobie 14/16
    RIVET CCP SEALED 6-6 (3/16 X 3/8)
    Misc
    Bolt Hex Head 1/4-20 X 2.25 Stainless Steel Murrays Part# 19-2221 Prindle 16/18 and Hobie® rudder bolt. Stainless steel 1/4-20 x 2-1/4" hex head bolt.
    BOLT HEX HEAD 1/4-20 X 2.25" (SS)
    Misc
    Hobie rivet casings sleeves seal rivets to prevent water penetration. When used with a rivet they seal the hole to prevent water from getting through the center of the rivet. Rivet Casings are recommended for use on all rivets on the mast to keep the mast water tight. Compatible with all 3/16 diameter rivets up to 5/8" long. Compatible with all rivets on Hobie, Nacra and Prindle catamarans except traveler tracks. Requires 13/64" hole. Hobie part number 8011291, 8011290, also called rivet cap.
    RIVET CASING 6-10(3/16 X 5/8)
    Hobie
    Screw 1/4-20 x 1" THMS-P SS Murrays Part# 50-8030701 Hobie® factory replacement 1/4-20 x 1" stainless steel screw. Used on Hobie® pre-EZ-Loc rudder system, tendon tiller connector, rudder adjuster, Hobie 20 shroud anchor plate. Applications: H18/ Hobie 18 SX Rudder Adjuster Screw: 1 Compare to Hobie Part# 8030701
    SCREW STAINLESS STEEL 1/4-20x1" THMS-P
    Hobie
    Nut Nylock 5/16-18 Low Profile Murrays Part# 50-8050331 Hobie® factory replacement low-profile 5/16-18 nylock nut.  Fits EZ Loc Upper and Lower Rudder Housing Hobie Bravo, Getaway and Wave. Hobie Part# 8050331
    NUT NYLOCK 5/16-18 LOW PRO
    Hobie
    Rivet CCP 6-10 (3/16 X 5/8) Murrays Part# 19-5034 Stainless steel 3/16" x 5/8" rounded pan head rivet. Compare to Hobie Cat® #8010121. Halyard mast cleat rivet
    RIVET CCP 6-10 (3/16 X 5/8)
    Misc
    Rivet CCP 6-8 (3/16 X 1/2) Murrays Part# 19-5033 Stainless steel 3/16" x 1/2" rounded pan head rivet. Compare to Hobie Cat® #8011231.
    RIVET CCP 6-8 (3/16 X 1/2)
    Misc
    Nut Nylock 3/8-24 Murrays Part# 50-8050511 Replacement 3/8-24 nylock nut is used on Hobie® 14, 16 and 18 dolphin striker rods, as well as Hobie® 17 inboard support. Hobie Part# 8050511
    NUT NYLOCK 3/8-24"
    Hobie
    RIVET CCP 6-6 (3/16 X 3/8) Murrays Part# 19-5032 Stainless steel 3/16" x 3/8" pan head rivet Among other uses, the Stainless steel 3/16" x 3/8" pan head rivet can be used when Hobie® rivet #8010131 is specified: Hobie 14 (2) or 16 (4) mast head Hobie Wave/Getaway/14/16/17/18/18SX/ mast base (4) Hobie 14/16 rudder upper casting (2) Hobie 14/16 tiller end cap (2) Hobie 14/16 boom front end cap (3) Pair with stainless steal rivet casings to seal the holes when using on the mast.
    RIVET CCP 6-6 (3/16 X 3/8)
    Hobie
    Murrays PN 001-0053 The Murrays Rudder Stiffening Spacer is a 2" diameter spacer for use on Hobie, Nacra and Prindle catamarans to eliminate excessive clearances between rudders and castings which cause rudder slop, side to side wobble, and thwart rudder alignment. A kit with spacers and nuts is also available (#01-2053).  The Murrays Rudder Stiffening Spacer are quite thin so that you can achieve a perfect fit. Standard kits come with 8 spacers.
    RUDDER STIFFENING SPACER
    Murrays Sports
    3/16 - 1/4" Split Ring Murrays Part# 22-9492 Stainless steel split ring (ring ding) for 3/16″-1/4″ diameter clevis pin. This is the standard size Hobie split ring used all over the boats, most commonly on the shrouds, forestay and roller furler Medium Split ring Dimensions: 5/8″ Diameter Material: 316 Stainless steel. This is the most common size Split ring on Hobie, Nacra and Prindle Catamarans. 20860000 Medium Clevis Ring.
    SPLIT RING 3/16-1/4"
    Misc
    Nut Nylock 5/16-18 Stainless Steel Murrays Part# 19-2520 5/16-18 nylock nut is used on Hobie® rudders. The stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Compare to Hobie Cat® item #8050311 and 8050321 shroud anchor pin nut Used with Hobie Getaway Bow Tang Bolt
    NUT NYLOCK 5/16-18 (SS)
    Misc
    Rivet CCP 6-4 (3/16 X 1/4) Murrays Part# 19-5031 Stainless steel 3/16" x 1/4" rounded pan head rivet. Compare to Hobie Cat® #8010181. This is a common rivet used on many extrusions. Hobie, Nacra, Prindle masts and booms. Pair with a rivet casing to seal the rivet hole when used on masts. All Hobie mast hounds, tangs, heads, and cheek blocks. Used with Hobie Getaway Bow Spreader Plates Used on Hobie Getaway FWD and REAR Crossbar Stop Plates
    RIVET CCP 6-4 (3/16 X 1/4)
    Misc
    1/2 BALL (NYLON) - Hobie half round washer spacer tiller connector - Hobie part number 11510000 HOBIE HALF SPHERE TILLER CONNECTOR
    NYLON 1/2" BALL
    Murrays Sports
    Hobie Drain Plug Screw Murrays Part# 50-8031731 This screw is used to hold the rudder housing in the back of many of the Hobie Beach cats. H14, H16, H17, H18 Hobie Part# 8031731
    HOBIE DRAIN PLUG SCREW
    Hobie
    Used for tiller connection on Hobie Cats®. The stainless 1/4-20 stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Equivalent to Hobie #8050111. Also Equivalent to Nacra/Prindle F123 gudgon nut for all Prindle and older Nacras. Applications: Hobie 18 / H18: Bow Tang Nut Qty: 6 Rudder Adjustment: 1 Hobie Getaway: Forestay Yoke Nut
    NYLOCK NUT 1/4-20 SS
    Misc
    Screw PHMS #10-32 X 1 Stainless Steel Slot Head Murrays Part# 19-2915 Stainless steel, pan head #10-32 x 1" machine screw with slot is used as dolphin striker screw on all Prindles. Replaces Murrays item #56-F112. Also used in some Hobie Applications, compare to 8030111 Hobie Part. Applications: H18/18 SX/16 and Getaway Tiller Hinge Screw: 2
    SCREW PHMS #10-32 X 1" (SS)
    Misc
    Comptip Cap Plug Murrays Part# 50-8090900 This part is used to seal the hole in the Comptip of a Hobie cat after the expanding foam has been put in. Hobie Part# 8090900
    Comptip Cap Plug
    Hobie
    NUT SQUARE 10-32 Murrays Part# 50-8051301 Hobie® factory replacement stainless steel 10-32 square nut can be used when mounting downhaul/halyard cleat on Hobie® 14 or 16. Also can be used for mounting H17 trampoline eye straps. Use 19-2910 screw. Hobie Part# 8051301
    NUT SQUARE 10-32
    Hobie
    Washer 5/16 X 9/16 Flat Murrays Part# 50-8080181 Hobie Part# 8080181
    WASHER FLAT 5/16 X 9/16"
    Hobie
    Cotter Pin 3/32 X 3/4 Murrays Part# 19-1015 Cotter pins are used on all Hobie, Nacra and Prindle rudder pins. They are used to secure the rudder pins. Compare to Hobie Cat® #8060111. Stainless steel cotter pin measures 3/32" x 3/4".
    COTTER PIN 3/32 X 3/4" SS
    Misc