NACRA 5.2 Upgrades

106 products

    106 products
    Murrays Part# 001-0062 Replacement tiller yoke assembly for all hiking sticks sold by Murrays. Used to connect the tiller extension to the tiller crossbar. Includes two contoured spacers that provide a solid platform for the yoke to sit on. Compare to Hobie Cat® Tiller yoke assembly #3205 or NACRA connection part tiller/joystick #31072 Applications: All Hobies and Prindles Tiller Yoke Assembly: 1
    Tller connection kit - yoke assembly - Hobie, Nacra, Prindle
    TILLER YOKE ASSEMBLY WITH SPACERS
    Murrays Sports
    Out of Stock
    Small Mast Tang Murrays Part# 56-6607 Stainless steel mast tang with four mounting holes is used for jib halyard or mounting spinnakers on Nacra cats. Use four #19-5031 rivets and #19-5020 casings for installation. Nacra part# 6607
    NACRA SMALL MAST TANG
    NACRA
    Spreader Tip Plate Murrays Part# 56-9842 Spreader tip plate for all Nacras and Prindle 18, 18.2 and 19. Nacra Sailing factory item# 30316
    NACRA SPREADER TIP PLATE
    NACRA
    Trap Shock Cord: Nacra, Prindle, Sol Cat and Getaway Murrays Part# 001-8019 A trapeze shock cord is an absolute necessity because it keeps the trapeze system in place and ready for hook-up. One hook connects to either the thimble on the trapeze wire or the adjustment line, then runs under the tramp and connects to the other side in the same location. A plastic carbine hook is installed on one end only; the other hook is included to be installed after the shock cord is put on the boat. Cord is 1/4" d
    NACRA/PRINDLE/SOL CAT AND GETAWAY TRAP SHOCK CORD
    Murrays Sports
    Hobie Cat #80550005 Main sail batten pocket protector kit. Hobie, Nacra, Prindle.
    MAIN SAIL POCKET PROTECTOR KIT
    Murrays Sports
    Zip Tech Zipper Lubricant 0.5oz Murrays Part# 38-1925 Zipper Lubricant for use on dry suits, and other tough zipper applications to ensure zippers operate properly and seal out the elements.
    ZIPPER LUBRICANT
    Misc
    Replacement sheave for mast head on Nacra 5.0, 5.2, 5.5, 5.7, 5.8, 6.0, 18 Square, Prindle 16 and Sol Cat 18 (cats that use a wire halyard). UV-resistant acetal material provides high strength and resistance to impact and wear, as well as excellent low friction properties for bearing applications.
    RONSTAN SHEAVE: P16 AND NACRA MAST HEAD
    Ronstan
    Prindle 18/19 Ronstan Mast Head Base Sheave Murrays Part# 56-6804 Replacement sheave for mast base on Prindle 15, 18, 18.2, 19 and Nacra 2003 and later mast head. Sheave measures 1-1/8" diameter x 3/8" wide. Please note that this item replaces #6803 that is no longer available.
    PRINDLE 18/19 RONSTAN MAST HEAD SHEAVE
    Ronstan
    Out of Stock
    Universal Drain Plug for most Hobie, Nacra and Prindle Catamarans which includes a gasket and fits most Hobie, Nacra and Prindle catamarans. Hobie part number 10091000
    Hobie drain plug 10091000 Hobie 18
    HOBIE DRAIN PLUG WITH GASKET
    Misc
    Dolphin Sticker Rod Nut Murrays Part# 56-F151 9/16" stainless nut for Nacra dolphin striker mast support rod. Used on boats built after 1983. Before threading nut onto rod, use grease or anti-seize on threads of rod to prevent thread galling. Performance Sports factory item #F151.
    NACRA DOLPHIN STRIKER ROD NUT
    NACRA
    Clevis Pin1/4 X 1" Murrays Part# 50-8020401 Hobie® factory replacement 1/4" x 1" clevis pin. Compare to Hobie Part Number 8020411 Applications: H18 / Hobie 18 SX Tiller Yoke Clevis Pin: 1
    CLEVIS PIN 1/4 X 1"
    Hobie
    Clevis Pin 1/4 X 3/4" Murrays Part# 56-4012 The Clevis Pin 1/4 X 3/4" is used on Prindle rudders, Nacra mast head sheave and as Nacra/Prindle shroud pin. Prindle Part# 4012
    CLEVIS PIN 1/4 X 3/4"
    NACRA
    Nacra Hammock Hook Murrays Part# 56-1034 Hammock hook (sideloader) for Nacra 5.2, 5.5, 5.8, 6.0 and 18SQ Nacra Sailing factory item# 30013
    NACRA HAMMOCK HOOK
    NACRA
    Gooseneck Bolt Murrays Part# 56-F131 3/8" x 1-1/2" gooseneck bolt for Nacra 5.2 and all Prindles. Performance Sports factory item # F131
    PRINDLE/NACRA GOOSENECK BOLT
    NACRA
    Stainless steel clevis pin. Measurement is 1/4" diameter x 5/8" grip length. Hobie part number 8020361, 8020381 and 8020380.
    1/4 X 5/8" Clevis Pin Murrays Part# 22-9802 Stainless steel clevis pin. Measurement is 1/4" diameter x 5/8" grip length (shoulder to the split ring hole).  Uses: Most commonly used to connect shrouds and forestays to 7 or 10 hole shroud adjusters on Hobie, Nacra and Prindle catamarans. Hobie 18 gooseneck vertex pin Hobie 18 outhaul car sheave pin Hobie Part# 8020361, 8020381 and 8020380
    CLEVIS PIN 1/4 X 5/8"
    Misc
    Clevis Pin 1/4 X 1/2 Murrays Part# 22-9808 Stainless steel clevis pin. Measurement is 1/4" diameter x 1/2" grip length (shoulder to the split ring hole). Substitute for Hobie Cat® #8020371.
    CLEVIS PIN 1/4 X 1/2"
    Misc
    Bolt Hex Head 5/16-18 X 1.5" Murrays Part# 19-2229 Use this stainless steel, 5/16-18 x 1-1/2" hex head bolt as beam strap bolt for Nacra. Substitute for Nacra Sailing factory item #30358. This bolt is also used to hold the cam stop plate on a Hobie Rudder Upper casting. Replaces Hobie Cat® Part# 8040301 and Murrays Part# 56-F164
    BOLT HEX HEAD 5/16-18 X 1.5"
    Misc
    Rudder Kick-Up Stop Murrays Part# 56-4518 The Nacra Rudder Kick-Up Stop is used on the Nacra 4.5/450, 5.0, 5.2, 5.5SL, 5.7, 5.8NA, 6.0NA, 5.5UNI and 18SQ. Performance Sports factory item# 4518
    NACRA RUDDER KICK-UP STOP
    NACRA
    RUDDER PIN SPRING CLIP: 3/8
    Misc
    Daggerboard Carpet Murrays Part# 56-1082 ​Approximately 1-1/2″ wide carpet installs in daggerboard wells. Nacra factory item #1083. Sold by the foot.
    DAGGERBOARD CARPET
    Murrays Sports
    Nacra Illustrated Old Parts List Murrays Part# 56-0300 Performance Sports factory parts list for "older" Nacras, including Nacra 4.5/450, 5.0, 5.2, 5.5SL, 5.7, 5.8NA, 6.0NA, 5.5Uni, 18SQ.
    NACRA ILLUSTRATED OLD PARTS LIST
    Murrays Sports
    3/16 - 1/4" Split Ring with Pigtail Murrays Part# 22-9491 A pigtail makes this split ring (ring ding) easier to open than standard split rings. For use on 3/16″ – 1/4″ clevis pins Material: 316 Stainless steel. Medium Split ring Dimensions: 5/8″ Diameter This is the most common size Split ring on Hobie, Nacra and Prindle Catamarans. Applications: All Hobies Shroud and Forestay split ring H18/ Hobie 18 SX – Tiller Yoke Clevis Pin Ring Also called Ring Ding, Clevis Ring, Cotter Ring or Ringy Ding
    3/16 - 1/4" SPLIT RING WITH PIGTAIL
    Misc
    Murrays PN 001-0053 The Murrays Rudder Stiffening Spacer is a 2" diameter spacer for use on Hobie, Nacra and Prindle catamarans to eliminate excessive clearances between rudders and castings which cause rudder slop, side to side wobble, and thwart rudder alignment. A kit with spacers and nuts is also available (#01-2053).  The Murrays Rudder Stiffening Spacer are quite thin so that you can achieve a perfect fit. Standard kits come with 8 spacers.
    RUDDER STIFFENING SPACER
    Murrays Sports
    Rivet Washer Nylon Commonly used on NACRA catamarans to insulate the stainless rivet from aluminum extrusions. Nacra PN 40200
    RIVET WASHER NYLON
    Murrays Sports
    Cotter Pin 3/32 X 3/4 Murrays Part# 19-1015 Cotter pins are used on all Hobie, Nacra and Prindle rudder pins. They are used to secure the rudder pins. Compare to Hobie Cat® #8060111. Stainless steel cotter pin measures 3/32" x 3/4".
    COTTER PIN 3/32 X 3/4" SS
    Misc
    Out of Stock
    N-5.2 TRAPEZE WIRES (2 HANDLES)
    Murrays Sports
    Recently viewed