Murrays Marine, Murrays Sports, Murrays.com Since 1969, Family owned

Murrays Marine

764 products
    Murrays has been an innovator in beach catamaran sailing since the late 60s and is still making new parts today.  Murrays is the performance sailing source.
    764 products
    Hobie 16 spare parts kit, shackle tool, drain plugs, rudder pins, clevis pins and rings, 3/16" bow shackle, 1/4" bow shackle, batten tie strings, and 3 mast bearings. Pouch comes in assorted colors as available. Hobie #30305 and #30306.
    H-14/16 SPARE PARTS KIT:
    Murrays Sports
    Hobie Sol Cat 18 Trapeze Wires (2 Handles) Trapeze Wire set for single trapeze. Use this page to order product numbers: 002-6253-01 002-6253-02
    Hobie Sol Cat 18 Trapeze Wires (2 Handles) Trapeze Wire set for single trapeze. Use this page to order product numbers: 002-6253-01 002-6253-02
    SOL-18 TRAPEZE WIRES (2)
    Murrays Sports
    SOL-18 MAIN HALYARD W/SHACKLE Main halyard for a 18' Sol Cat catamaran.
    SOL-18 MAIN HALYARD WITH SHACKLE
    Murrays Sports
    SOL-18 BRIDLE 1/8" WHITE WIRE
    Murrays Sports
    Out of Stock
    Snap Shackle With Tack 1/4" Murrays Part# 22-4501 Swiveling tack shackle with 1/4" clevis pin. Use on hexaratchets on Hobie® 18, Nacra or Prindle. To connect the swivel shackle to an item that requires a 3/16" clevis pin, you will need a 3/16" clevis pin with 7/8" shaft. Also convenient for the jib tack connection on Nacras and Inters.
    SNAP SHACKLE WITH TACK 1/4"
    Murrays Sports
    SMALL BLOCK W/REMOVABLE SHEAVE This small block is used on trapeze adjustment systems where the removable sheave enables installation without cutting wires. Specifications: 1-3/16" removable sheave, Teflon® bearing and 5/16" line capacity. Hobie item #3103
    SMALL BLOCK W/REMOVABLE SHEAVE This small block is used on trapeze adjustment systems where the removable sheave enables installation without cutting wires. Specifications: 1-3/16" removable sheave, Teflon® bearing and 5/16" line capacity. Hobie item #3103
    SMALL BLOCK WITH REMOVABLE SHEAVE
    Murrays Sports
    Sister Clip Micro  Murrays Part# 004-7730 The stainless steel micro sister clip is a quick connector with no moving parts. The micro sister clip does not have a slot.
    SISTER CLIP MICRO (EA)
    Murrays Sports
    Sidewinder Becket Murrays Part# 005-0701 Add on becket for classic Harken Mainsheet systems. The sidewinder becket is for older Harken 2.25" or 3.00" triple blocks. It enables extra purchase ratio without sacrificing low profile block stacking. Some drilling is required for installation.
    SIDEWINDER BECKET
    Murrays Sports
    Sail Pocket Protector Kit Jib Murrays Part# 001-1002 The Jib Sail Pocket Protector Kit includes one pair of tough nylon protectors with indentations for included rivets that are set with a hammer.
    JIB SAIL POCKET PROTECTOR KIT
    Murrays Sports
    Hobie Cat #80550005 Main sail batten pocket protector kit. Hobie, Nacra, Prindle.
    MAIN SAIL POCKET PROTECTOR KIT
    Murrays Sports
    SAIL "HC" LOGO U-CUT PR BLACK
    Murrays Sports
    Rudder Stiffening Kit Murrays Part# 001-2053 The Rudder Stiffening Kit for all Hobies eliminates excessive clearances between rudders and castings which cause wobble and thwart rudder alignment. Kit has 4 stainless nylock nuts and 8 spacers. Compare to Hobie Cat® item #136.
    RUDDER STIFFENING KIT
    Murrays Sports
    Murrays PN 001-0053 The Murrays Rudder Stiffening Spacer is a 2" diameter spacer for use on Hobie, Nacra and Prindle catamarans to eliminate excessive clearances between rudders and castings which cause rudder slop, side to side wobble, and thwart rudder alignment. A kit with spacers and nuts is also available (#01-2053).  The Murrays Rudder Stiffening Spacer are quite thin so that you can achieve a perfect fit. Standard kits come with 8 spacers.
    RUDDER STIFFENING SPACER
    Murrays Sports
    Rudder Pin Nacra, Prindle and H21 Stainless Steel Murrays Part# 001-5273 Long-wearing, weight-saving, hollow stainless rudder pins with strong, .065" wall provide reduced wear and the best long-term fit. These rudder pins measure 3/8" x 10-1/4" end-to-end with a hole at each end. They will fit Nacra, Prindle and Hobie® 21. Cotter pins are included. These pins are a replacement for Hobie® factory item #40880011 (sold individually). Sold in pairs
    NACRA/PRINDLE AND H21 SS RUDDER PIN
    Murrays Sports
    H14/16 Rudder Return Hand Shock Cord Murrays Part# 001-2240 Two 32" shock cords with balls keep your Hobie® 14 or 16 rudders down when the cams don't! Order Kisme Kleets #05-1010 separately, if needed.
    H-14/16 RUDDER RETURN HAND SHOCK CORD
    Murrays Sports
    Rudder Pins H17/18 Stainless Steel Murrays Part# 001-4273 Weight-saving compared to solid stainless steel pins, hollow stainless rudder pins with still beefy .065″ wall provide reduced wear and the good long-term durability. The universal stainless steel 3/8″ x 9-1/4″ rudder pins are suited for; Hobie 17/18/20 rudder castings. Also used on older Hobie Wave and Getaways with metal rudder castings. Cotter pins are included. Alternative to Hobie Cat® #60880011.  (* Pre EZ LOC Rudder c
    H-17/18 RUDDER PINS PR (SS)
    Murrays Sports
    H14/16 Rudder Pins Stainless Steel Murrays Part# 001-2269 Weight-saving, hollow stainless rudder pins for Hobie® 14 or Hobie® 16 with stronger .065" wall provide reduced wear and the best long-term fit. This kit includes one pair of 3/8" x 8" rudder pins with cotter pins. New One piece rudder gudgeons have been produced with a slightly smaller metric hole size. If you have a 2020 and newer boat or 2020 and newer one piece gudgeons, our aluminum rudder pins may require force to install and be diff
    H-14/16 RUDDER PINS PR (STAINLESS)
    Murrays Sports
    Rudder Pin Nacra, Prindle and H21 (Aluminum) Murrays Part# 001-5272 Aluminum rudder pins for Nacra, Prindle and Hobie® 21 measure 3/8" x 10-1/4" end-to-end, with hole at each end. Cotter pins are included. Sold in pairs
    NACRA/PRINDLE AND H21 ALUMINIUM RUDDER PIN
    Murrays Sports
    Rudder Pins H14/16 Pair (Nylon) Murrays Part# 001-2271 Nylatron rudder pins are sacrificial for use in the surf (they'll break before your rudder system does) and should be inspected often for wear. Pair of 3/8" x 8" rudder pins with cotter pins for Hobie® 14 or Hobie® 16. Each pair is equivalent to two Hobie Cat® item #10881000 Sold in pairs
    H-14/16 NYLON RUDDER PINS PR
    Murrays Sports
    Rudder Pins H17, H18, Wave, Getaway (Aluminum) Murrays Part# 001-4274 Aluminum rudder pins for the Hobie 17, 18, Wave and Getaway.  Aluminum 3/8″ x 9-1/4″ rudder pins, cotter pins are included.  Sold in pairs Compare to Hobie Cat® #60880001
    H-17/18/WAVE AND GETAWAY ALUMINUM RUDDER PINS
    Murrays Sports
    H14/16 Aluminum Rudder Pins Murrays Part# 001-2272 Aluminum rudder pins are standard on Hobie® 14 and 16 and are good for all-around, low maintenance use. Pair of 3/8" x 8" rudder pins with cotter pins. New One piece rudder gudgeons have been produced with a slightly smaller metric hole size. If you have a 2020 and newer boat or 2020 and newer one piece gudgeons, our aluminum rudder pins may require force to install and be difficult to remove. The stainless pins are a better fit. Sold in pairs
    H-14/16 ALUMINUM RUDDER PINS
    Murrays Sports
    Rudder Pins H17/18 (Nylon) Murrays Part# 001-4271 Nylatron rudder pins are sacrificial for use in the surf (they'll break before your rudder system does) and should be inspected often for wear. These universal 3/8" x 9-1/4" nylon rudder pins are suited for all Hobie® 17/18/Wave rudder castings. Compare to Hobie Cat® #5052 fiberglass rudder pins (pair).
    RUDDER PINS H-17/18 PR (NYLON)
    Murrays Sports
    H14/16 Upper Gudgeon Murrays Part# 25-3351 This latest, strongest design with welded sleeve bushings provides large, smooth bearing surfaces between rudder pins and gudgeons. Replace flared gudgeons with their sharp edges and point loading that can cause early rudder pin failure. For Hobie® 14's, 16's and 17, order separate upper and lower gudgeons.  For all other Hobie® cats Part# 25-3352 for both gudgeons. Each This gudgeon is a replacement for item #50101301
    H-14/16 UPPER GUDGEON
    Murrays Sports
    The Murrays Rudder Cam Sister Screws: Hobie 14, Hobie 16 are a pair of sister screws for Hobie 14 and 16 rudder cams. These pins are much easier to install and remove than the stock pin and they are reusable! Sold in pairs Hobie Cat Part# 10470000 Hobie Part# 5201
    The Murrays Rudder Cam Sister Screws: Hobie 14, Hobie 16 are a pair of sister screws for Hobie 14 and 16 rudder cams. These pins are much easier to install and remove than the stock pin and they are reusable! Sold in pairs Hobie Cat Part# 10470000 Hobie Part# 5201
    H-14/16 RUDDER CAM SISTER SCREWS
    Murrays Sports
    Rudder Cam Screws H17, H18, H20, Older Wave and Getaway Murrays Part# 001-3551 The Murrays Rudder Cam Pins are a pair of sister screws for use on the Hobie 17, 18, 20, 21, as well as the older Hobie Wave and Getaway rudder cams. These pins are an upgrade form the original stock hollow flare rivet that came on the Hobie. The Sister Screws are much easier to install and remove, and they are reusable. Compare to Hobie Cat® #5203 and #50312301. Sold in pairs
    H-17/18/20/OLDER WAVE AND GETAWAY RUDDER CAM PINS
    Murrays Sports
    Out of Stock
    H17/18/20/21/Wave and Getaway Rudder Cam Kit Murrays Part# 001-3550 The Rudder Cam Kit: H17, H18, H20, H21, Wave, & Getaway are replacement rudder cams which help keep your Hobie’s rudder lock-down mechanism functioning properly. This kit includes sister screws to install the cams, making it easier to replace the cams. Purchase the complete kit if your boat has the stock flare pins; or you can purchase just the cams (#50-10480000 each) if your boat already has sister screws.
    H-17/18/20/21/WAVE AND GETAWAY RUDDER CAM KIT
    Murrays Sports
    Out of Stock
    Murrays Part# 001-2050 The Hobie Rudder Cam Kit: Hobie 14, Hobie 16 are replacement rudder cams to keep the rudder lock-down mechanism on your Hobie Cat® functioning properly. The Hobie® 14 or 16 kit includes two cams, two reusable, internally threaded sister screws for both sides, and instructions. Purchase the complete kit if your boat has the stock flare pins; purchase just the cams (#50-10480000 each) if your boat already has sister screws.  Compare to Hobie Cat® #5202.
    H-14/16 RUDDER CAM KIT
    Murrays Sports
    Rope Lock (Nylon) Murrays Part# 001-0120 Easy-to-adjust black rope lock commonly used for trapeze height adjustment. Standard rope stop on Hobie®, Nacra and Prindle. Double-up back-to-back for extra strength. Hobie part number 61530000 for this rope lock. Works on 3/16 to 1/4" line
    NYLON ROPE LOCK
    Murrays Sports
    Heavy Duty Swivel with Aluminum Cam Roller Fairlead Murrays Part# 25-3020 Swivel cam cleats are ideal for main traveler control and up-release jib cleating systems. This is a Murrays product that features an Aluminum Harken 150 cam cleat, and HD swivel plate and a HD roller fairlead. The advantage to the roller fairlead is that it can take a larger line diameter, up to 1/2", and handle heavy loads at extreme angles. Making it ideal for larger catamarans and sailors in high wind areas.
    ROLLER FAIRLEAD KIT (SWIVEL)
    Murrays Sports
    RING SS WELDED 3/16"x 1" ID
    Murrays Sports
    Ring: 1/4 X 2 Diameter (Stainless Steel) Murrays Part# 25-3050 1/4" x 2" stainless ring can be used for Prindle-style jib halyards.
    RING: 1/4 X 2" DIAMETER (SS)
    Murrays Sports
    Righting Bag Only (200+LBS) Murrays Part# 001-3282 This is the bag only from Murrays' popular Cat Righting Big Bag System (#01-3280). The 18" x 32" bag attaches with hook and loop straps under the tramp for easy use and storage. The theoretical maximum capacity of the bag is 250 lbs.
    RIGHTING BAG ONLY (200+LBS)
    Murrays Sports
    Out of Stock
    Ring Stainless Steel Welded 1/8"x3/4"ID
    RING SS WELDED 1/8"x3/4"ID
    Murrays Sports
    Out of Stock
    REPLACEMENT HOBIE WIND VANE Hobie part number CM7703
    REPLACEMENT HOBIE WIND VANE
    Murrays Sports
    Replaceable Aluminum Trap Handle Murrays Part# 007-2010 Foam-covered aluminum handle is easily installed onto existing trapeze wire. Carry a spare as a temporary repair, then replace the wire at your convenience. Each. Hobie Cat® Part# 2010
    REPLACABLE ALUMINUM TRAP HANDLE
    Murrays Sports
    Quick-Release Convenience Package: H16 Murrays Part# 001-3231 This package makes set-up and take-down of your Hobie 16® more convenient. Kit includes: One #18-4R125 Quick Release Pin for hiking stick to crossbar connection. One #18-3M075L Quick Release Pin with Lanyard for mainsheet block to traveler car connection. One #21-1032 Quick Twist Halyard Shackle for jibsheet blocks to jib clew boom to mast connection. One #21-1155L Toggle Pin with Lanyard for forestay to adjuster connection. Four #01-0127 Car
    H-16 QUICK RELEASE CONVENIENCE PACKAGE
    Murrays Sports
    Replace a 3/16" bow shackle with this quick-release version to add convenience. Can be used on 2-1/4" blocks. Compare to Hobie Cat® #3062.
    QUICK RELEASE 3/16" BOW SHACKLE
    Murrays Sports
    Out of Stock
    Hobie 3062 1/4" Bow shackle with quick release pin
    QUICK RELEASE 1/4" BOW SHACKLE
    Murrays Sports
    PWC Footstrap Kit Murrays Part# 001-2020 The PWC Footstrap Kit includes a pair of footstraps, twist control system and fasteners. A pre-formed arch prevents collapsing, so your foot slides right in and is cradled by the comfortable 7mm neoprene padding. Sold in pairs
    PWC FOOTSTRAP KIT (PR)
    Murrays Sports
    Out of Stock
    POWER RIGHTING SYSTEM WITHOUT POLE
    Murrays Sports
    Recently viewed