In Stock

In Stock

2261 products

    Everything Murrays Marine carries, all in one place.  Catamaran parts, Kiteboarding and wing foiling central. Use the filters on the side or the search up top to refine your search.

    2261 products
    Trampoline H21SE Mesh 1-Piece Black Murrays Part# 30-3105TEF Aftermarket one-piece, bias-cut black mesh tramp for Hobie® 21 Special Edition is not Hobie Class-legal for racing. Includes trapeze grommets, one Velcro halyard pocket and standard thread; Teflon (PTFE) thread extends the life of the tramp and is available for an additional charge.
    H-21SE 1PC MESH TRAMPOLINE WITH TEFLON THREAD-BLACK
    Murrays Sports
    H21 Special Edition Bridle 5/32" Wire Murrays Part# 002-0515-22 One bridle for Hobie® 21SE (Special Edition) is constructed of 5/32" wire to factory specifications. The H21SE is sometimes confused with the H21SC (Sport Cruiser). Please note that the H21SE is differentiated by its 10' beam and lack of a front trampoline. Use this page to order product numbers: 002-0515-21 White 002-0515-22 Black
    H-21SE BRIDLE 5/32" BLACK WIRE
    Murrays Sports
    H21 Special Edition Diamond Wire without Turnbuckle Murrays Part# 002-0595-20 Diamond wire without turnbuckle for Hobie® 21SE (Special Edition) is constructed to factory specifications. The H21SE is sometimes confused with the H21SC (Sport Cruiser). Please note that the H21SE is differentiated by its 10' beam and lack of a front tramp.
    H-21SE DIAMOND WIRE WITHOUT TURNBUCKLE
    Murrays Sports
    H-21 SE Double Trapeze (4 handles) The Murrays Double Trapeze is a set of 4 black or white coated trap wires with 4 handles for double trapezing. A single thimble per pair of handles eliminates clutter at that mast connection. Order shock cord, harness loops and adjustment kits separately. A complete trapeze system requires the following: Harness loop - Can't Miss Ring or Dogbone Trap Shock Cord Trap Adjustment kit Sailing Harness ​Trapeze adjustment kits (#001-1121, 001-1130 or 001-1140, purchased
    H-21SE DOUBLE TRAPEZE (4)
    Murrays Sports
    H21SE Forestay 5/32" Wire Murrays Part# 002-0545-32 Forestay for Hobie® 21SE (Special Edition) is constructed to factory specifications. The H21SE is sometimes confused with the H21SC (Sport Cruiser). Please note that the H21SE is differentiated by its 10' beam and lack of a front tramp.
    H-21SE FORESTAY 5/32" BLACK WIRE
    Murrays Sports
    H21 Special Edition Jib Halyard with Shackle Murrays Part# 002-0586-00 Jib halyard with shackle for Hobie® 21SE (Special Edition) is constructed to factory specifications. The H21SE is sometimes confused with the H21SC (Sport Cruiser). Please note that the H21SE is differentiated by its 10' beam and lack of a front tramp.
    H-21SE JIB HALYARD WITH SHACKLE
    Murrays Sports
    H21 Special Edition Shroud 5/32" Black Wire Roller Swaged Murrays Part# 002-0505-12 Single shroud (sidestay) for Hobie® 21 Special Edition has hydraulically swaged fittings for a cleaner, stronger shroud. It is constructed to factory specifications. The H21SE is sometimes confused with the H21SC (Sport Cruiser). Note: The H21SE is differentiated by its 10' beam and lack of a front trampoline.
    H-21SE SHROUD 5/32" BLACK WIRE ROLLER SWAGED
    Murrays Sports
    H21SE Upper Forestay 5/32" Wire Murrays Part# 002-0535-02 Black upper forestay for Hobie® 21 Special Edition is constructed to factory specifications. The H21SE is sometimes confused with the H21SC (Sport Cruiser). Please note that the H21SE is differentiated by its 10' beam and lack of a front tramp.
    H-21SE UPPER FORESTAY 5/32" BLACK WIRE
    Murrays Sports
    The Murrays Hobie Getaway line package contrains all the lines on a Hobie Getaway. The Main and Jib sheets are Robline Neptune 500 and the control lines are Pelican VLS, Very Low Stretch.
    H-GETAWAY LINE PACKAGE
    Murrays Sports
    H14/16 Mast Bearing (Pack of 100) Murrays Part# 001-2042 Teflon® mast bearings for Hobie® 14 or 16 are .06" thick and will form to mast base with first use. Package of 100 mast chips.
    H14/16 MAST BEARING (100-PKG)
    Murrays Sports
    The Hobie 16 and 14 Surefoot EVA Deck Grip Kit features 3m peel and stick backing on cut-diamond-textured EVA foam. Ideal rail and or deck grip on all dinghies and catamarans. EVA traction pads offer grip, padding and a long life span.  EVA is a lightweight foam doesn’t absorb water the way carpet does, so it dries quickly! Includes​ four 4" x 40" strips - covers both sidebars. Compare to Hobie Cat® Rail Rug #1671BLK.
    The Hobie 16 and 14 Surefoot EVA Deck Grip Kit features 3m peel and stick backing on cut-diamond-textured EVA foam. Ideal rail and or deck grip on all dinghies and catamarans. EVA traction pads offer grip, padding and a long life span.  EVA is a lightweight foam doesn’t absorb water the way carpet does, so it dries quickly! Includes​ four 4" x 40" strips - covers both sidebars. Compare to Hobie Cat® Rail Rug #1671BLK.
    H14/16 SUREFOOT EVA KIT
    Murrays Sports
    H14/16 Rudder Cast Upper Right Black Murrays Part# 50-10362011 Hobie® factory replacement upper left rudder casting for Hobie® 14 or 16. Requires two 6-6 rivets (item #19-5032) and one 6-8 rivet (item #19-5033) to install tiller tube.
    H14/16 UPPER RIGHT RUDDER CASTING-BLACK
    Hobie
    This is for use on the classic style Hobie 16 jib halyard system with a short upper forestay and metal pulley up near the mast tang that was standard in the 70s, 80s and early 90s. There are 2 styles of Hobie 16 jib halyard. This wire Hobie 16 jib halyard works with the old style upper and lower forestay and the metal halyard pulley. The 2nd style is the Aussie jib halyard with it's parallel forestay and jib halyard that became stock in the mid 1990s. Compare to Hobie Part# 20661001
    H16 JIB HALYARD WITH LINE
    Murrays Sports
    Hobie 16 Main Halyard Non-Comptip is a wire halyard for the all-aluminum mast (non Comp-Tip) Hobie 16 and is used to raise the main sail. Constructed to factory specifications, and includes a 2nd stopper as a reef point stopper. This is the standard halyard for Hobie 16's with an all aluminum mast which were standard before 1986. Hobie part number 20651011
    H16 MAIN HALYARD WITH LINE (NON-COMPTIP)
    Murrays Sports
    H18SX/21sc WING TRAMPOLINES Murrays Hobie 18SX and 21SC Wing Trampolines. Lace on. Sold as a pair. Compare to Hobie part number 68040255 Not compatible with the Hobie 18 Magnum.
    H18SX/21sc WING TRAMPOLINES Murrays Hobie 18SX and 21SC Wing Trampolines.  Lace on.  Sold as a pair.   Compare to Hobie part number 68040255 Not compatible with the Hobie 18 Magnum.
    H18SX/21SC WING TRAMPOLINES-BLACK
    Murrays Sports
    H20/21 Super Cruiser Compression Sleeve Murays Part# 50-31110001 This is the sleeve that goes over the dolphin striker inside the front crossbar of the H20. Hobie part# 31110001
    H20/21SC COMPRESSION SLEEVE
    Murrays Sports
    Halyard 5"X 9" Zip Pouch-Assorted Colors Murrays Part# 31-1400 The Murrays 5" x 9" zippered halyard pouch is constructed of rugged, water-resistant material with plastic hooks at each end to attach to the tramp lacing. The off-center zipper is designed for easy stuffing of your boat's halyard. The pouch is also handy for storing replacement parts, keys, and safety gear. Assorted colors. We have this pouch made for us right here in the U.S.A. Compare to Hobie Cat® stow bag #72000B and 7
    HALYARD 5"X9" ZIP POUCH- ASSORTED COLORS
    Murrays Sports
    Halyard Cleat Kit with Rivets Murrays Part# 001-1019 The Murrays Halyard Cleat Kit with Rivets pulls the halyard out of the way to keep the battens from hanging up on the halyard of an H16. The kit includes the halyard cleat and sealed stainless rivets. Center-to-center hole spacing is 31mm. *Photo is out of date and kit no longer comes with casings as the rivets that are included come sealed. Compare to Hobie Cat Part 10730000
    HALYARD CLEAT KIT WITH RIVETS
    Murrays Sports
    HAND WINCH 3:1
    Misc
    Harken 1/4" Torlon Ball Bearing-21 Balls Murrays Part# 28-0177 1/4" Torlon replacement ball bearings fit Harken 158, 159, 172, 210, 212, 214, 215, 249, 440 and 441. A bearing loader, #28-HSB8 (sold separately), is required for installation. Sold in packages of 21
    HARKEN 1/4" TORLON BALL BEARING (21)
    Harken
    Harken 10:1 Mainsheet Carbo Air Base Block Murrays Part# 56-9953 This Carbo AirBlock® has an enormous working range, with a higher working load than a standard block, even though it is lighter in weight. The Carbo Ratchet block allows sailors to hand-hold loaded lines and offers balance between holding power and controlled easing. The base block has an on-off ratchet and will roll freely in both directions when disengaged, such as in light air.
    HARKEN 10:1 MAINSHEET CARBO AIR BASE BLOCK
    Harken
    Harken 12:1 Mainsheet Carbo Boom Block Murrays Part# 56-9966 Harken 57mm triple fiddle block with swivel used for 12:1 mainsheet systems on beach cats. Low-friction Carbo AirBlocks® are lightweight, strong, reliable and affordable. These small, compact blocks have very high working loads for safe, easy trimming. Specifications: Sheave Diameter: 2-1/4" Length: 6" Maximum Line Diameter: 7/16" Maximum Working Load: 2380 lb. Breaking Strength: 5000 lb. Weight: 11.15 oz. Harken Part# HSB379
    HARKEN 12:1 MAINSHEET CARBO BOOM BLOCK
    Harken
    Harken 12:1 Mainsheet Carbo Ratchamatic Base Harken 57 mm triple fiddle with reinforced cam arms that is used for 12:1 mainsheet systems on beach cats. Low-friction Carbo AirBlocks® are lightweight, strong, reliable and affordable. Companions to the popular Harken® Black Magic® line, these small, compact blocks have very high working loads for safe, easy trimming.
    HARKEN 12:1 MAINSHEET CARBO RATCHAMATIC BASE
    Harken
    Harken 150 Cam-Matic Cleat Rebuild Kit - 1993 and Newer Murrays Part# 28-0150KIT This rebuild kit is the answer when plastic parts on Harken's 150 Cam-Matic® Cleat have worn out or suffered UV damage, and/or when the springs need to be replaced.
    HARKEN 150 CAM-MATIC CLEAT REBUILD KIT-1993 & NEWER
    Harken
    Harken 16mm Block-Becket Murrays Part# 28-0405 The Harken air block offers a very high load in an extremely lightweight block. Excellent for control lines. The overall length is only 1-1/2" long. The 5/8" sheave will accept line as large as 7/32". 250 lb. SWL; 1200 lb. breaking strength.  The 16 mm is Harken’s smallest block. It is perfect for small synthetic control lines found on high-tech dinghies. The patented bearing system uses stainless steel balls in a captive grooved race and has a 250 lb.
    HARKEN 16MM BLOCK-BECKET
    Harken
    Harken 16mm Block-Swivel Murrays Part# 28-0417 The Harken air block offers a very high load in an extremely lightweight block. The block itself is only 1-13/16" long. The 5/8" sheave will accept line as large as 7/32". 250 lb. SWL; 750 lb. breaking strength; 5/32" shackle pin diameter. Harken Part# 417
    HARKEN 16MM BLOCK-SWIVEL
    Harken
    Harken 16mm Cheek Block Murrays Part# 28-0416 Harken's 16mm check block is a downhaul and turning block and is perfect for small synthetic control lines. 1-13/16" long; 5/8" sheave diameter; 250 lb. SWL; 1200 lb. breaking strength. Use #8 (4mm) RH fasteners. Harken Part# 416
    HARKEN 16MM CHEEK BLOCK
    Harken
    Harken 16mm Cheek Pivot Block Murrays Part# 28-0432 The 16 mm is Harken’s smallest block. It is perfect for small synthetic control lines found on high-tech dinghies. The patented bearing system uses stainless steel balls in a captive grooved race and has a 250 lb. (113 kg) maximum working load.
    HARKEN 16MM CHEEK PIVOT BLOCK
    Harken
    Harken 16mm Double Block Murrays Part# 28-0406 The Harken air block offers a very high load in an extremely lightweight block. Excellent for control lines. The block itself is only 1-1/8" long; overall length is 1-11/16. The 5/8" sheave will accept line as large as 7/32". 450 lb. SWL; 1200 lb. breaking strength. The 16 mm is Harken’s® smallest block. It is perfect for small synthetic control lines found on high-tech dinghies.
    HARKEN 16MM DOUBLE BLOCK
    Harken
    Harken 16mm Double Block-Becket Murrays Part# 28-0407 The 16 mm is Harken’s smallest block. It is perfect for small synthetic control lines found on high-tech dinghies. The patented bearing system uses stainless steel balls in a captive grooved race. Harken Part# 407
    HARKEN 16MM DOUBLE BLOCK-BECKET
    Harken
    Harken16mm Forkhead Block Murrays Part# 28-0376 16 mm Forkhead Block is Harken’s® smallest block. It is perfect for small synthetic control lines found on high-tech dinghies. The patented bearing system uses stainless steel balls in a captive grooved race and has a 250 lb. (113 kg) maximum working load.  Harken part # 376
    HARKEN 16mm FORK HEAD BLOCK
    Harken
    Harken Sheave Ball Bearing 16mm The Harken Sheave Ball Bearing 16mm is the replacement for Harken 16mm air blocks. UV-stabilized Delrin® sheave with stainless steel ball bearings. Specifications: 5/8" sheave diameter; 3/16" hole diameter, 5/16" wide; 3/16" maximum line diameter; 250 lb. safe working load. Harken #415.
    HARKEN 16MM SHEAVE
    Harken
    Harken 16mm Single Murrays Part# 28-0404 The Harken air block offers a very high load in an extremely lightweight block. Excellent for control lines. The block itself is only 1-1/8" long. The 5/8" sheave will accept line as large as 7/32". 250 lb. SWL; 1200 lb. breaking strength.
    HARKEN 16MM SINGLE
    Harken
    Harken 16mm Triple Block Murrays Part# 28-0408 The Harken air block offers a very high load in an extremely lightweight block. The block is only 1-13/16" long. The 5/8" sheave will accept line as large as 7/32". 700 lb. SWL; 1200 lb. breaking strength.  Harken Part# 408
    HARKEN 16MM TRIPLE BLOCK
    Harken
    Harken 2698 18mm FLY SOFT-ATTACH BLOCK
    HARKEN 18MM FLY SOFT-ATTACH BLOCK
    Harken
    Harken 18mm Fly Soft-Attach Double Block Murrays part# 28-2158 Harken soft-attach Fly blocks are designed to provide strength without mass, providing sailors with big power in a low-aero package. Designed specifically for high-tech line, these efficient blocks have an incredible working load for their small size. Fly blocks are perfect for use on foiling dinghies and sport boats and for vang cascades and backstay systems on Grand-Prix racers.
    HARKEN 18MM FLY SOFT-ATTACH DOUBLE BLOCK
    Harken
    Harken Block Single 2.25" Hexaratchet Murrays Part# 28-0019 Sheave Size 57mm 2.25" Max Line Size 10mm 3/8" Max Working Load 227KG 500lb Breaking Strength 907kg 2000lb Holding Power 10:1 Hexaratchets grip loaded sheets, yet allow sailors to ease and trim quickly and with complete control. A switch on the side engages and disengages the ratchet mechanism. Use the 043 or 044 revers ratchets with the 019 or 050 single with becket on spinnaker and jib sheets where ratchets rotate in opposite directions an
    HARKEN 2.25" HEXARATCHET BLOCK-SWIVEL, STARBOARD
    Harken
    Harken 22mm Becket Block Murrays Part# 28-0225 Low-friction Micro blocks are compact and lightweight. They are ideal for sailboards, smaller dinghies, and lightly loaded control lines on boats of all sizes. Harken ball bearing micro single block with becket has stainless side plates.
    HARKEN 22MM BECKET BLOCK
    Harken
    Harken 22mm Cheek Block Murrays Part# 28-0233 Harken micro cheek is used as a downhaul and turning block and as the Hobie 16 jib traveler control line block on the front crossbar. Specifications: 200 lb. SWL 1200 lb. breaking strength 1/4" maximum line diameter 7/8" sheave diameter 2-1/2" long
    HARKEN 22MM CHEEK BLOCK
    Harken
    HARKEN 22MM END STOPS HIGH-BEAM
    Harken
    Recently viewed