HOBIE Wave Parts

124 products

    124 products
    Eyestrap Wave Bridle Murrays Part# 50-38120011 ​Hobie® factory replacement eyestrap for Hobie Wave bridle.
    WAVE BRIDLE EYESTRAP
    Hobie
    Detent Plunger EZ Lock System Murrays Part# 50-20492021 Hobie Cat® factory detent plunger for EZ Loc rudder assembly. Hobie Bravo, Getaway and Wave Hobie Part# 20492021
    BRAVO/WAVE/GETAWAY DETENT PLUNGER EZ LOC SYSTEM
    Hobie
    Comp-Tip Mast Head Sheave for H16 Wave Murrays Part# 50-20614210 CompTip Mast Head Sheave for Hobie 16 or Wave, is the sheave found at the top of the comptip assembly. Two sheaves are used in each assembly. The sheaves each ride on a, comptip sheave spacer. The sheave is 9/16" wide x 2 1/4" diameter with 3/8" hole. The larger sheave for the obsolete mast head for all-aluminum mast is no longer available. Hobie Part number 20614210
    H-16/WAVE COMP-TIP MAST HEAD SHEAVE
    Hobie
    Wave/Getaway Shroud Anchor Plate Murrays Part# 50-39100011 Hobie® factory replacement shroud anchor chain plate for Club Wave or Getaway. The Club Wave has a three-piece trampoline and shrouds and bridles connect with clevis pins. Current boats use two plates per side. Hobie Part# 39100011
    WAVE/GETAWAY SHROUD ANCHOR PLATE
    Hobie
    Batten Cap Jib Leech H16 Murrays Part# 50-2133000 Hobie® factory jib leech batten cap for Hobie® 16. For batten tie, use 18" of 1/8" Dacron® solid braid #39-0221. These are also used on the top two battens of a Hobie Wave and the top batten of a Hobie 18 Mainsail. Sold individually
    H-16 JIB BATTEN LEECH CAP (EA)
    Hobie
    Murrays Part# 50-10432000 Hobie® factory 2½" spring for Hobie® 16 lower rudder casting. This spring is longer and stiffer than original equipment (#50-10430000), providing additional tension if you are having trouble with rudder kick up. Used on Hobie 18 Rudder Systems from late 80s through now. Used on Hobie 16 Rudder Systems after 1983 Used on Hobie Getaway Rudder Systems pre- EZ Loc Hobie part number 10432000
    HOBIE RUDDER SPRING-LONG
    Hobie
    Out of Stock
    H-20/WAVE DRAIN PLUG WITH WASHER
    Hobie
    Rudder Casting Lock Spring Murray Part# 50-10430000 Hobie factory replacement 2-1/8" lock spring for rudder casting. Replace rudder springs with this original spring supplied on Hobie® 14, 16, (pre 1983) 17 and 18. Compare to HC part number 10430000 H14, H16, H17, H18, H20
    HOBIE RUDDER SPRING
    Hobie
    Wave Mainsheet S Hook Murrays Part# 50-38900031 Hobie® factory replacement S-hook for Wave mainsheet. Mainsheet is 35 feet of Dacron® spun braid #39-055. Makes it easy to attach mainsheet to sail and standard on all new boats. Hobie Part# 38900031
    WAVE MAINSTEET S HOOK
    Hobie
    Hobie 18 rudder plunger. Hobie Part number 50312201. Also use on the 17 as well as the older Wave and Getaway
    H-17/18/GETAWAY RUDDER CAST PLUNGER
    Hobie
    RUDDER CASTING DELRIN SCREW - rudder locking adjustment screw - 60450000
    HOBIE DELRIN RUDDER SCREW
    Hobie
    Batten Cap Main Luff (EA) Murrays Part# 50-11322011 Main luff batten cap for Hobie Cats are sold individually. Order batten tie separately; 18" of line per batten cap is standard. Hobie® factory replacement part.
    MAIN LUFF BATTEN CAP (EA)
    Hobie
    Mast Step Pin Wave/Getaway .25 x 2" Detent Murrays Part# 50-8020451 Replacement mast step pin / mast hinge pin for a Hobie Wave and Getaway. 1/4" x 2" detent pin.   Hobie part # 8020451
    MAST STEP DETENT PIN .25x2"
    Hobie
    Wave Assembly Manual Murrays Part# 50-38450000 Hobie® factory assembly manual for the Wave catamaran. The manual is also available for free download at the Hobie Cat® Web site.
    WAVE ASSEMBLY MANUAL
    Hobie
    Hobie Tiller End Cap (Tendon Style) Murrays Part# 50-37561001 Hobie® factory replacement tendon-style tiller end cap Hobie Part# 37561001
    HOBIE TILLER END CAP (TENDON STYLE)
    Hobie
    Out of Stock
    Hobie Wave Lower Pintle Bushing Murrays Part# 50-38360001 This is the lower bushing for the original Wave or Getaway rudder castings. This fits into the aluminum rudder castings PRE- EZLoc rudder assemblies. This also fits Getaway and Bravo Pre-Ez Loc assemblies. Hobie Part# 38360001
    HOBIE WAVE LOWER PINTLE BUSHING
    Hobie
    Retainer Clip EZ Lock Rudder Housing Murrays Part# 50-90880231 Retainer clip for Hobie Bravo EZ Loc Rudder Housing. Hobie Part# 90880231
    BRAVO RETAINER CLIP EZ LOCK RUDDER HOUSING
    Hobie
    Screw Delrin 3/8-16 X .75" Murrays Part# 50-8032001 Hobie® factory replacement 3/8-16 x 3/4" Delrin screw is used as rudder rake adjustment screw on Pre-EZ Lock Rudder System. Hobie Part# 8032001
    SCREW DELRIN 3/8-16 X .75"
    Hobie
    Hobie factory replacement retainer clip for Hobie 20-style tiller connector and adjuster kit (#07-1953). TILLER CONNECTION RETAINER CLIP - HOBIE 20. 40590000 MURRAYS.COM - IN STOCK
    H-20 TILLER CONNECTOR RETAINER CLIP
    Hobie
    Out of Stock
    H-14/16 FOAM PLUG FOR PYLON
    Hobie
    Hobie factory tiller connector insert bearing for Hobie 20 Miracle. Hobie part number 40680001. Murrays.com - in stock
    HOBIE TILLER CONNECTOR INSERT BEARING
    Hobie
    Out of Stock
    H16 Masthead Sheave Spacer Murrays Part# 50-20614231 H16 Masthead Sheave Spacer. This is a replacement bearing surface for the comptip masthead sheaves in H16 mastheads. Fits Hobie Getaway Masthead Sheaves Hobie Part# 20644231
    H-16 MASTHEAD SHEAVE SPACER
    Hobie
    Out of Stock
    Hobie Wave Hull Seal Cap Murrays Part# 50-38370001 Hobie® factory replacement hull seal for under the seat pad on Wave. Hobie Part# 38370001
    WAVE HULL SEAL CAP
    Hobie
    Bolt 5/16-18 x 2-1/2" HX HD Murrays Part# 50-8040321 EZ Loc Lower Rudder Bolt for Hobie Bravo, Getaway and Wave. Hobie Part# 8040321
    BOLT 5/16-18 x 2-1/2" HX HD
    Hobie
    Screw 12x24x1 Pan Head (Long Lock) Murrays Part# 50-8030402 This screw is used to hold the rudder gudgeons on the back of the boat.  Hobie Part# 8030402
    SCREW 12x24x1 PAN HEAD (LONG LOCK)
    Hobie
    Out of Stock
    Bolt 5/16-18 x 2-3/4" HX HD Murrays Part# 50-8040391 EZ Loc upper rudder bolt for Hobie Bravo, Getaway and Wave  Hobie Part# 8040391
    BOLT 5/16-18 x 2-3/4" HX HD
    Hobie
    Clevis Pin 1/4X3/8 Murrays Part# 50-8020371 This is commonly used for Hobie Rigging parts. It has a 3/8" grip length. You can also use the 1/2" grip length pins also. Hobie Part# 8020371 or 8020370
    CLEVIS PIN 1/4 x 3/8"
    Hobie
    Rivet MSP 6-10 3/16 X 5/8" PH Murrays Part# 19-5023 Rounded pan head 3/16" x 5/8" Monel rivet. Compare to Hobie Cat® Part# 8010121
    RIVET MSP 6-10 3/16 X 5/8" PH
    Hobie
    Black Mast Caution Decal Murrays Part# 50-13440000 The Decal Mast Caution Black Hobie® factory caution decal attaches to mast as a reminder to watch for overhead power lines when sailing and/or launching your boat.
    BLACK MAST CAUTION DECAL
    Hobie
    Out of Stock
    Decal Mast Caution Orange Murrays Part# 13440010 Hobie® factory decal attaches to mast as a reminder to watch for overhead power lines when sailing and/or launching your boat. Hobie Part# 13440010
    ORANGE MAST CAUTION DECAL
    Hobie
    Bolt Hex 5/16-18 X 1" Murrays Part# 50-8040171 Hobie® factory hex head bolt measures 5/16-18 x 1". Used on #07-1953 Tiller Connector for Hobie® 20. Hobie Part# 8040171
    BOLT HEX 5/16-18 X 1"
    Hobie
    Hobie factory replacement long lock screw for EZ Loc rudder system. Specs: 12-24X3/4 long lock PHMS screw Hobie PN 8030411
    EZ LOC LONG SCREW
    Hobie
    Nut Nylock 5/16-18 Low Profile Murrays Part# 50-8050331 Hobie® factory replacement low-profile 5/16-18 nylock nut.  Fits EZ Loc Upper and Lower Rudder Housing Hobie Bravo, Getaway and Wave. Hobie Part# 8050331
    NUT NYLOCK 5/16"-18 LOW PRO
    Hobie
    Screw 1/4-20 x 5/8 PHMS-P Stainless Steel Murrays Part# 50-8030331 This screw is used on the Hobie wave to secure the eye straps to the inner edge of the crossbars for connecting the tramp pulleys on the classic wave or "other" on the club version.
    SCREW 1/4-20 x 5/8" PHMS-P SS
    Hobie
    Hobie rivet casings sleeves seal rivets to prevent water penetration. When used with a rivet they seal the hole to prevent water from getting through the center of the rivet. Rivet Casings are recommended for use on all rivets on the mast to keep the mast water tight. Compatible with all 3/16 diameter rivets up to 5/8" long. Compatible with all rivets on Hobie, Nacra and Prindle catamarans except traveler tracks. Requires 13/64" hole. Hobie part number 8011291, 8011290, also called rivet cap.
    RIVET CASING 6-10(3/16 X 5/8)
    Hobie
    GETAWAY WING PIN/EZ LOC RUDDER LANYARD Replacement lanyard for Hobie Getaway Wing Pins and EZ Loc rudder up pin kit. Hobie part number 50314001
    HOBIE GETAWAY WING LEG LANYARD
    Hobie
    Out of Stock
    RIVET MCP 6-8 3/16x1/2" PH Murrays Part# 50-8011231 Hobie® factory 6-8 heavy duty rivet requires a rivet tool for installation. 3/16" x 1/2" pan head. Fits Hobie Getaway Eyelet Post. Fits Hobie 20 Eyelet Post. Mounts Wave Mast Step Hobie part number 8011231
    RIVET MCP 6-8 3/16x1/2" PH
    Hobie
    Screw Boom Clamp 10-24 X 1.25 FHMS-S Murrays Part# 50-8031011 Hobie® factory replacement screw for the boom clamp (#50-61711000) on the Hobie 18. #10-24 x 1-1/4" flat head machine stainless screw with Phillips head. Hobie Part# 8031011
    SCREW 10-24x 1-1/4"
    Hobie
    Washer 3/8 X 3/4 Nylon for 07-1953 Murrays Part# 50-8080691 Washer for tiller arm bolt #50-8040171. Hobie® factory item
    WASHER NYLON 3/8 X 3/4"
    Hobie
    Nut 10-32 Nylock Low Profile Murrays Part# 50-8050211 Hobie factory low-profile Nylock 10-32 nut as used on EZ-Loc rudder assembly. Hobie Part# 8050211
    NUT 10-32 NYLOCK LOW PROFILE
    Hobie
    Recently viewed