Hobie 18 Mast Parts

70 products

    Parts for your Hobie 18 Mast

    70 products
    Out of Stock
    hobie-18-mast-60610010
    H-18 MAST ASSEMBLY
    Hobie
    Out of Stock
    H18 Comptip Assembly Murrays Part# 50-60611100 Hobie® factory Hobie 18 CompTip Assembly for Hobie 18 mast. A CompTip is the upper section of Hobie mast built in or after 1968. Fiberglass and non-conductive, it is designed to prevent electrocution by contact with a high power line.
    H-18 COMPTIP ASSEMBLY
    Hobie
    UNIVERSAL MAMA BOB MAST FLOAT The Hobie Mama Bob Universal Mast Float Kit aids in preventing your boat from going full turtle (mast straight down) when capsized, helping to prevent damage to your rig and sails should they contact the bottom. This model (Hobie® Cat #30112) is mast-side mounted system. The Universal Mama Bob float has been adapted for use as a shaft-mounted "universal" mast float that does not rotate, but is held in a fore-aft position in alignment with the mast for minimum drag while
    MAST FLOAT UNIVERSAL MAMA BOB
    Hobie
    Downhaul Kit 8:1 H18 Murrays Part# 001-2150 This is a performance upgrade downhaul kit that give increased performance control for your Hobie 18 Catamaran. The downhaul leads are run to the side of the boat for crew control and the loads are oriented to reduce sail tack damage that is common on the H18. It takes minutes to install with a rivet gun a drill and approximate measuring. The kit was born from a discussion at the 2023 NACs wherein many of the boats in Division 4 have a variation of the
    H-18 DOWNHAUL KIT 8:1
    Murrays Sports
    HOBIE 18 POWER DOWNHAUL KIT - 5:1 Get powerful downhaul adjustment from any sailing position. This Class-legal, 5:1 downhaul kit for Hobie® 18 includes a space-saving bracket with becket, two Harken bullet cheek blocks, Harken pivoting exit block with micro cleat, Harken double bullet block, trim line, fasteners and instructions.
    H-18 5:1 POWER DOWNHAUL KIT
    Murrays Sports
    Out of Stock
    H18 Mast Step Kit Murrays Part# 50-60180011 Hobie® factory replacement mast step kit for Hobie® 18 includes mast step casting, post, bearing, screw and washer. This is an upgrade for older Hobie 18's with threaded post.
    H-18 MAST STEP KIT
    Hobie
    Out of Stock
    H14/18/18SX/20/Wave Comp-tip Luff Track 87" Murrays Part# 50-38584001 Hobie factory replacement 87" luff track for Hobie Cats except Hobie 16 and Getaway.  Older H18 comp tips were one long piece of plastic, newer boats have two sections. This plastic piece, and shorter aluminum piece. If you are replacing an older one piece luff track, you will also need to purchase the aluminum top section as well.
    H-14/18/18SX/20/WAVE COMP-TIP LUFF TRACK
    Hobie
    H18 Diamond Wire Complete Murrays Part# 50-61750001 Replacement Hobie 18 diamond wire assembly, including the turnbuckle, diamond wire roller and end fittings.
    H-18 DIAMOND WIRE COMPLETE
    Hobie
    H18SX Diamond Wire without Turnbuckle Murrays Part# 002-0694-20 Diamond wire for Hobie® 18SX is constructed with stainless fork, jib roller and left-hand threaded stud. Turnbuckle not included. Compare to Hobie Cat® Part# 68750001
    H-18SX DIAMOND WIRE WITHOUT TURNBUCKLE
    Murrays Sports
    Hobie 18 Mast Base Hinge casting 60650011
    H-18 MAST BASE HINGE
    Murrays Sports
    Hobie 18 Mastbase Hinge Murrays Part# 50-60650011 Mastbase hinge for the Hobie 18. Factory supplied part for all Hobie 18 masts. Mastbase hinge for the Hobie 18. Does not include hardware for mounting.
    HOBIE 18 MAST BASE HINGE
    Hobie
    Out of Stock
    H18/20 Updated Luff Track 12.5" Murrays Part# 50-50404101 Hobie® factory aluminum luff track update is 12-1/2" long The Hobie 20 need the extra strength to prevent the sail from pulling out of the luff track. The Hobie 18 uses this as an extension to the wave luff track, the extra strength is great but was not stock on the boat.
    H-18/20 UPDATED LUFF TRACK 12.5"
    Hobie
    H18 Diamond Spreader Tang Murrays Part# 50-61410000 Hobie® factory replacement diamond spreader tang for Hobie® 18.
    H-18 DIAMOND SPREADER TANG
    Hobie
    Harken 396 - 29mm Harken 180 Pivoting Block with Carbo-Cam, downhaul, Hobie.
    HARKEN 29MM PIVOTING LEAD BLOCK-CARBO-CAM CLEAT
    Harken
    Out of Stock
    H18/20 Comptip Mast Head Murrays Part# 50-60602041 Hobie 18/20 Comp Tip Mast Head factory replacement mast head for Hobie® 18 or 20 with Comp Tip.
    H-18/20 COMPTIP MAST HEAD
    Hobie
    Out of Stock
    H18 Mast Base Casting-Black Murrays Part# 50-60641031 Hobie® factory replacement black mast base casting for Hobie® 18. Use four #19-5032 rivets for installation.
    H-18 MAST BASE CASTING-BLACK
    Hobie
    H16/18/Getaway Mast Tang Murrays Part# 50-20690000 Hobie® factory replacement mast tang for Hobie® 16, 18, Getaway and the 1995 and newer Hobie® 17. Use twelve 6-4 rivets (#19-5031) and twelve casings (#19-5020) for installation. Also known as a mast hound
    H-16/18/GETAWAY MAST TANG
    Hobie
    Out of Stock
    H18 Spreader Arm Murrays Part# 50-61420000 Hobie® factory replacement spreader arm for Hobie® 18.
    H-18 SPREADER ARM
    Hobie
    Out of Stock
    Compression Plate Assembly Kit H18 Murrays Part# 50-60680001 Hobie® factory mast compression plate assembly kit for Hobie 18 and 18SX
    H-18 COMPRESSION PLATE ASSEMBLY KIT
    Hobie
    Out of Stock
    Hobie Halyard Twist Shackle Murrays Part# 50-60670000 Classic 3/16 inch stainless steel twist shackle from Hobie Cat. Hobie Part# 60670000
    HOBIE HALYARD TWIST SHACKLE
    Hobie
    Sale
    Hobie 18 Mast Base Casting Clear Anodized
    Hobie
    Save $25
    Hobie Aussie Halyard Ring Murrays Part# 007-3064 If you're having trouble raising or lowering your mainsail due to a faulty halyard ring and shackle, this upgrade will help. Welded ring and lanyard give you more positive control while hooking or unhooking the ring to the hook. Use on any boat that uses a hook at the mast head and a ring and shackle at the head of the sail. Personal preference dictates whether you choose this ring or the Murrays Aussie Ring (#01-4216). Hobie® Part# 3064
    HOBIE AUSSIE HALYARD RING
    Hobie
    Mast Rotation Control Arm Murrays Part# 25-3040 Stainless mast rotation control arm is strong and smooth! Arm #25-3040 with 1/4″ hole is for all Hobies except for the Hobie® 17, Prindles and Nacras; Arm #25-3041 with 5/16″ hole is for Nacras, Prindles and the Hobie® 17. H17 uses #19-2235 bolt Hobie Part# 61210001
    MAST ROTATION CONTROL ARM
    Murrays Sports
    TURNBUCKLE COMPLETE 5/32"
    Misc
    Harken Sail Chafe Protector Murrays Part# 28-0285 Harken's Sail Chafe Protector Set replaces the diamond wire rollers to protect the jib from chafing on the diamond wire spreader. The split rollers are pre-drilled to fit up to 3/16" wire. Each 2-3/4"-diameter (70mm) protector has two pieces that snap together for easy installation. Used on Hobie 18, Hobie 20, Prindle 18.2, Prindle 19, Nacra 15, 17, 18, Inter 20, F18
    HARKEN SAIL CHAFE PROTECTOR (2)
    Harken
    Main Halyard Ring (Murrays) Murrays Part# 001-4216 If you're having trouble raising or lowering your mainsail due to a faulty halyard ring and shackle, this upgrade will help. Welded ring and lanyard give you more positive control while hooking or unhooking the ring to the hook. Use on any boat that uses a hook at the mast head and a ring and shackle at the head of the sail. Personal preference dictates whether you choose this ring or the Hobie Aussie Ring (#07-3064). This item replaces discontinued Part
    MAIN HALYARD RING (MURRAYS)
    Murrays Sports
    Out of Stock
    Spreader Arm Slide Murrays Part# 50-61440000 Hobie® factory replacement spreader arm slide. Discontinued by Hobie - feel free to email us to see about used options
    HOBIE SPREADER ARM SLIDE
    Hobie
    H18/20 Gooseneck Yoke Murrays Part# 50-60710000 Hobie® factory replacement gooseneck yoke for Hobie 18 and 20. Hobie Part# 60710000
    H-18/20 GOOSENECK YOKE
    Hobie
    H18 Halyard Lock (Comptip) Murrays Part# 50-61610101 Halyard hook for Hobie 18 comptip mast assembly. Hobie Part# 61610101
    H-18 HALYARD HOOK (COMPTIP)
    Hobie
    Hobie Halyard Ring with Loop Murrays Part# 50-61290021 Stainless steel halyward ring with loop, used on many Hobie Cat sailboats. Recommended for use with Hobie's twisted halyard shackle Hobie Part# 61290021
    HOBIE HALYARD RING WITH LOOP
    Hobie
    Out of Stock
    V JAM CLEAT BOOM (3/16" HOLES)
    Hobie
    SUPER GOOSE H-17/18/20/21 This upgraded gooseneck by Tren Tec is constructed from a solid block of 6061-T6 aluminum and then finished with a coat of black hardkote anodizing. The Super Goose is for Hobie® 17 (newer), 18, 20 and 21; not compatible with older Hobie® 17 model. Hobie part number 1510
    H-17/18/20/21 SUPER GOOSE
    Tren-Tec
    Murrays Part# 001-4045 Hobie 18 Mast Bearing Kit enables smooth mast rotation on the Hobie® 18. The kit includes a new mast bearing, stainless steel washers and Teflon washer. To mount, use one #19-3019 screw (included) for post-1990 Hobie 18 or one #19-3020 screw (sold separately) for pre-1990 Hobie 18. Compare to Hobie Cat® #1132 (bearing 60110000 and Teflon™ washer).
    Hobie 18 mast bearing 60110000 and 1132
    HOBIE 18 MAST BEARING KIT
    Murrays Sports
    Ronstan 5/16 bow with hole shackle RF638 - Hobie 20700001 and SP150081
    RONSTAN 5/16" BOW SHACKLE WITH HOLE
    Ronstan
    Hobie Sail Feeder Kit Murrays Part# 50-80100501 Replacement sail feeder for use on many Hobie Cat mast assemblies to make raising your mainsail easier than ever! Hobie®'s Sail Feeder helps the sail feed evenly into the mast track without catching and/or tearing the sail.
    HOBIE SAIL FEEDER KIT
    Hobie
    Ronstan Stainless Steel Bow Shackle, 5/16" Pin, Coined Head with Hole Murrays Part# 21-0636 The Ronstan 5/16 Bow Shackle has 5/16" diameter pin. Compare to Hobie® #20700001 and SP150081. Standard all Hobie, Nacra and Prindle catamarans to attach the standing rigging to the mast tang.
    Ronstan bow shackle measurements
    RONSTAN 5/16" BOW SHACKLE
    Ronstan
    Hobie Gooseneck Hinge Vertex Murrays Part# 50-50772031 Hobie® factory replacement gooseneck vertex for all Hobie® Cats. Hobie Part# 50772031
    HOBIE GOOSENECK HINGE VERTEX
    Hobie
    Out of Stock
    H18 Mast Bearing Murrays Part# 50-60110000 Hobie Cat® factory mast bearing for Hobie 18. This part sits on the mast step to facilitate mast rotation on the Hobie 18. Hobie part# 60110000
    H-18 MAST BEARING
    Hobie
    Out of Stock
    Hobie Spreader Covers Murrays part# 007-3262 These vinyl spreader bar end covers are real sail-savers! The black, smooth resilient covers protect the jib luff from wear and tear from cotter keys and sharp edges. Pair. Hobie Cat® factory item #3262.
    HOBIE SPREADER COVERS
    Hobie
    Ronstan Series 20 Utility Block, Tube Rivet Murrays Part# 21-0661 Rontan's cheek block is a Hobie® 18 and Prindle downhaul and turning block. Stainless steel cheeks and Acetal sheaves ensure a long service life with virtually no maintenance. Hollow rivets in the block heads can be fitted with shackles, which can also be used to add a becket for extra purchase.
    RONSTAN MIDGET SINGLE BLOCK (CHEEK)
    Ronstan
    Recently viewed