Hobie 18 Mast Parts

73 products

    Parts for your Hobie 18 Mast

    73 products
    Out of Stock
    Hobie Spreader Covers Murrays part# 007-3262 These vinyl spreader bar end covers are real sail-savers! The black, smooth resilient covers protect the jib luff from wear and tear from cotter keys and sharp edges. Pair. Hobie Cat® factory item #3262.
    HOBIE SPREADER COVERS
    Hobie
    Ronstan Series 20 Utility Block, Tube Rivet Murrays Part# 21-0661 Rontan's cheek block is a Hobie® 18 and Prindle downhaul and turning block. Stainless steel cheeks and Acetal sheaves ensure a long service life with virtually no maintenance. Hollow rivets in the block heads can be fitted with shackles, which can also be used to add a becket for extra purchase.
    RONSTAN MIDGET SINGLE BLOCK (CHEEK)
    Ronstan
    DIAMOND WIRE ROLLER
    Misc
    Out of Stock
    Diamond Wire Tang Murrays Part# 50-61480000 Hobie® factory replacement diamond wire tang Hobie Part# 61480000
    DIAMOND WIRE TANG
    Hobie
    H17/18 Mast Seal Plate Murrays Part# 50-61080000 Replacement mast seal plate for the Hobie 17 or Hobie 18.  Hobie Part# 61080000
    H-17/18 MAST SEAL PLATE
    Hobie
    H18 Mast Head/Base Sheave Murrays Part# 50-60620000 Factory replacement sheave for Hobie 18 mast head/base and outhaul assembly. Specs: 1" Diameter x 3/8" wide and 1/4" hole. Also used as traveler control line turning sheave on 2005 and newer Hobie 16 sailboats. Applications: Hobie 18 - Mast head halyard sheave ; mast base halyard sheave ; outhaul car sheaves. Hobie 16 - Jib Traveler line sheave. (in the H16 Race Corner Castings) use 50-8011251 Rivet
    H-18 MAST HEAD/BASE SHEAVE
    Hobie
    Ronstan Stainless Steel Bow Shackle, 3/16" Pin, Coined Head Murrays Part# 21-0634 Solid stainless steel bow shackle has 3/16" diameter pin.  UDL BL - The “Uniformly Distributed Load” breaking load of the shackle; the load is applied across the full span of the shackle pin. PL BL - The “Point Load” breaking load of the shackle; the load is only applied at the center or one side of the shackle pin.
    Ronstan bow shackle measurements
    RONSTAN STAINLESS STEEL BOW SHACKLE, 3/16" PIN, COINED HEAD
    Ronstan
    Quick-Release Pin Detent 1/4 X 1-1/2 Murrays Part# 18-4D150 The Quick-Release Pin Detent 1/4 X 1-1/2 is an economical, quick connection for Hobie 16 mast step pin. A spring-loaded ball exerts sufficient pressure to help avoid accidental release. Measurements are 1/4″ diameter x 1-1/2″ maximum grip length (distance from the shoulder to the locking ball bearings).
    QUICK RELEASE DETENT PIN 1/4 X 1-1/2"
    Misc
    H18 Compression Sleeve Murrays Part# 50-61490000 Hobie® factory replacement compression sleeve for mast of Hobie 18.
    H-18 COMPRESSION SLEEVE
    Hobie
    Hobie 18 mast step hinge pin, has a hole on one end only. The headless clevis pin measures 1/4″ diameter by 3-3/8″ grip length Hobie Part # 8020501
    HEADLESS CLEVIS PIN 1/4 X 3-3/8"
    Misc
    Out of Stock
    H17/18 Mast Foam Plug Murrays Part# 50-60060000 Hobie® factory replacement foam plug for Hobie® 17 or 18 mast.
    H-17/18 MAST FOAM PLUG
    Hobie
    3/16 X 7/8" Clevis Pin Murrays Part# 22-9806 3/16 x 7/8 Clevis Pin.  H16 gooseneck shackle clevis pin. Hobie Part# 8020061
    CLEVIS PIN 3/16 X 7/8"
    Misc
    Bolt Hex Head 1/4-20 X 5" (Stainless Steel) Murrays Part# 19-2226 Stainless steel 1/4-20 x 5" hex head bolt is used for Hobie® 18 mast rotation arm. Use #19-2516 nut. Equivalent to Hobie® Part# 8040111
    BOLT HEX HEAD 1/4-20 X 5" (SS)
    Misc
    Clevis Pin1/4 X 1" Murrays Part# 50-8020401 Hobie® factory replacement 1/4" x 1" clevis pin. Compare to Hobie Part Number 8020411 Applications: H18 / Hobie 18 SX Tiller Yoke Clevis Pin: 1
    CLEVIS PIN 1/4 X 1"
    Hobie
    3/16 X 1/2" Clevis Pin Murrays Part# 22-9801 Stainless steel clevis pin measures 3/16" diameter x 1/2" grip length (shoulder to the split ring hole). Prindle / Nacra Part# 9412 Compare to Hobie Cat® Part# 8020041
    CLEVIS PIN 3/16 x 1/2"
    Misc
    Stainless steel clevis pin. Measurement is 1/4" diameter x 1-3/4" grip length (shoulder to the split ring hole). Uses: This pin replaces #56-7809, gooseneck clevis pin for Nacra 5.2 and all Prindles. Hobie 18 main traveler car  Prindle Part# 6004  Comparable to Hobie Cat® Part# 8020431
    1/4 X 1-3/8" Clevis Pin Murrays Part# 22-9804 Stainless steel clevis pin. Measurement is 1/4" diameter x 1-3/4" grip length (shoulder to the split ring hole). This pin replaces #56-7809, gooseneck clevis pin for Nacra 5.2 and all Prindles. Prindle Part# 6004 Comparable to Hobie Cat® Part# 8020431
    CLEVIS PIN 1/4 X 1-3/8"
    Misc
    Clevis Pin 1/4 x .83" Murrays Part# 50-8020391 Hobie® factory clevis pin measures 1/4" diameter x .8285" grip length (shoulder to the split ring hole).
    CLEVIS PIN 1/4 X .83"
    Hobie
    Stainless steel clevis pin. Measurement is 1/4" diameter x 5/8" grip length. Hobie part number 8020361, 8020381 and 8020380.
    1/4 X 5/8" Clevis Pin Murrays Part# 22-9802 Stainless steel clevis pin. Measurement is 1/4" diameter x 5/8" grip length (shoulder to the split ring hole).  Uses: Most commonly used to connect shrouds and forestays to 7 or 10 hole shroud adjusters on Hobie, Nacra and Prindle catamarans. Hobie 18 gooseneck vertex pin Hobie 18 outhaul car sheave pin Hobie Part# 8020361, 8020381 and 8020380
    CLEVIS PIN 1/4 X 5/8"
    Misc
    Clevis Pin 1/4X3/8 Murrays Part# 50-8020371 This is commonly used for Hobie Rigging parts. It has a 3/8" grip length. You can also use the 1/2" grip length pins also. Hobie Part# 8020371 or 8020370
    CLEVIS PIN 1/4 x 3/8"
    Hobie
    Black Mast Caution Decal Murrays Part# 50-13440000 The Decal Mast Caution Black Hobie® factory caution decal attaches to mast as a reminder to watch for overhead power lines when sailing and/or launching your boat.
    BLACK MAST CAUTION DECAL
    Hobie
    Out of Stock
    Decal Mast Caution Orange Murrays Part# 13440010 Hobie® factory decal attaches to mast as a reminder to watch for overhead power lines when sailing and/or launching your boat. Hobie Part# 13440010
    ORANGE MAST CAUTION DECAL
    Hobie
    Sealed Rivet CCP 6-8 (3/16 X 1/2) Murrays Part# 19-5033S Sealed rivets have a sealed end that does not require rivet casings to make them water tight. One and done, no casing needed, just insert and pop as you would a normal rivet, and your hole will be sealed. Sealed Stainless steel 3/16" x 1/2" rounded pan head rivet. Compare to Hobie Cat® #8011231 Rivet and Hobie Cat® #8011291 rivet casing.
    RIVET CCP SEALED 6-8 (3/16 X 1/2)
    Misc
    Sealed Stainless Steel 3/16" x 3/8" Pan Head Rivet Murrays Part# 19-5032S Sealed rivets have a sealed end that does not require rivet casings to make them water tight. One and done, no casing needed, just insert and pop as you would a normal rivet, and your hole will be sealed. Among other uses, the Stainless steel 3/16" x 3/8" pan head rivet can be used when Hobie® rivet #8010131 is specified: Hobie 14 (2) or 16 (4) mast head Hobie Wave/Getaway/14/16/17/18/18SX/ mast base (4) Hobie 14/16
    RIVET CCP SEALED 6-6 (3/16 X 3/8)
    Misc
    Hobie rivet casings sleeves seal rivets to prevent water penetration. When used with a rivet they seal the hole to prevent water from getting through the center of the rivet. Rivet Casings are recommended for use on all rivets on the mast to keep the mast water tight. Compatible with all 3/16 diameter rivets up to 5/8" long. Compatible with all rivets on Hobie, Nacra and Prindle catamarans except traveler tracks. Requires 13/64" hole. Hobie part number 8011291, 8011290, also called rivet cap.
    RIVET CASING 6-10(3/16 X 5/8)
    Hobie
    Rivet CCP 6-10 (3/16 X 5/8) Murrays Part# 19-5034 Stainless steel 3/16" x 5/8" rounded pan head rivet. Compare to Hobie Cat® #8010121. Halyard mast cleat rivet
    RIVET CCP 6-10 (3/16 X 5/8)
    Misc
    Rivet CCP 6-8 (3/16 X 1/2) Murrays Part# 19-5033 Stainless steel 3/16" x 1/2" rounded pan head rivet. Compare to Hobie Cat® #8011231.
    RIVET CCP 6-8 (3/16 X 1/2)
    Misc
    RIVET CCP 6-6 (3/16 X 3/8) Murrays Part# 19-5032 Stainless steel 3/16" x 3/8" pan head rivet Among other uses, the Stainless steel 3/16" x 3/8" pan head rivet can be used when Hobie® rivet #8010131 is specified: Hobie 14 (2) or 16 (4) mast head Hobie Wave/Getaway/14/16/17/18/18SX/ mast base (4) Hobie 14/16 rudder upper casting (2) Hobie 14/16 tiller end cap (2) Hobie 14/16 boom front end cap (3) Pair with stainless steal rivet casings to seal the holes when using on the mast.
    RIVET CCP 6-6 (3/16 X 3/8)
    Misc
    3/16 - 1/4" Split Ring Murrays Part# 22-9492 Stainless steel split ring (ring ding) for 3/16″-1/4″ diameter clevis pin. This is the standard size Hobie split ring used all over the boats, most commonly on the shrouds, forestay and roller furler Medium Split ring Dimensions: 5/8″ Diameter Material: 316 Stainless steel. This is the most common size Split ring on Hobie, Nacra and Prindle Catamarans. 20860000 Medium Clevis Ring.
    3/16-1/4" SPLIT RING
    Misc
    Nut Nylock 5/16-18 Stainless Steel Murrays Part# 19-2520 5/16-18 nylock nut is used on Hobie® rudders. The stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Compare to Hobie Cat® item #8050311 and 8050321 shroud anchor pin nut Used with Hobie Getaway Bow Tang Bolt
    NUT NYLOCK 5/16-18 (SS)
    Misc
    Used for tiller connection on Hobie Cats®. The stainless 1/4-20 stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Equivalent to Hobie #8050111. Also Equivalent to Nacra/Prindle F123 gudgon nut for all Prindle and older Nacras. Applications: Hobie 18 / H18: Bow Tang Nut Qty: 6 Rudder Adjustment: 1 Hobie Getaway: Forestay Yoke Nut
    NYLOCK NUT 1/4-20 SS
    Misc
    Nut Nylock #10-32 Stainless Steel Thick Murrays Part# 19-2515 Mainsheet block replacement nut. The stainless hex nut with nylock insert will not rust or work loose if properly installed. Fits Hobie Main Traveler Car. Fits Hobie Tiller Hinge Screw. Fits Hobie Masthead Sheave Screw H16 Hobie Getaway Compare to Hobie Part Number 8050201
    NUT NYLOCK #10-32 (SS) THICK
    Misc
    Screw PHMS #10-32 X 1 Stainless Steel Slot Head Murrays Part# 19-2915 Stainless steel, pan head #10-32 x 1" machine screw with slot is used as dolphin striker screw on all Prindles. Replaces Murrays item #56-F112. Also used in some Hobie Applications, compare to 8030111 Hobie Part. Applications: H18/18 SX/16 and Getaway Tiller Hinge Screw: 2
    SCREW PHMS #10-32 X 1" (SS)
    Misc
    Comptip Cap Plug Murrays Part# 50-8090900 This part is used to seal the hole in the Comptip of a Hobie cat after the expanding foam has been put in. Hobie Part# 8090900
    COMP-TIP CAP PLUG
    Hobie
    Recently viewed