All Prindle 18-2 Parts

106 products

    106 products
    Main Halyard Ring (Murrays) Murrays Part# 001-4216 If you're having trouble raising or lowering your mainsail due to a faulty halyard ring and shackle, this upgrade will help. Welded ring and lanyard give you more positive control while hooking or unhooking the ring to the hook. Use on any boat that uses a hook at the mast head and a ring and shackle at the head of the sail. Personal preference dictates whether you choose this ring or the Hobie Aussie Ring (#07-3064). This item replaces discontinued Part
    MAIN HALYARD RING (MURRAYS)
    Murrays Sports
    Rudder Locking Bolt Murrays Part# 56-4017 The Prindle Rudder Locking Bolt is the factory replacement bolt for rudder locking system on all Prindles. Tip: Be sure to check for proper alignment of the lock bolt to spring bolt. Any bent component will prevent the system from working properly. Identify and replace the bent portion to get your rudder system functioning properly. Performance Sports factory item# 4017
    PRINDLE RUDDER LOCKING BOLT
    NACRA
    Snap Shackle With Tack 1/4" Murrays Part# 22-4501 Swiveling tack shackle with 1/4" clevis pin. Use on hexaratchets on Hobie® 18, Nacra or Prindle. To connect the swivel shackle to an item that requires a 3/16" clevis pin, you will need a 3/16" clevis pin with 7/8" shaft. Also convenient for the jib tack connection on Nacras and Inters.
    SNAP SHACKLE WITH TACK 1/4"
    Murrays Sports
    1/4" QUICK RELEASE BOW SHACKLE
    Murrays Sports
    Rudder Pin Nacra, Prindle and H21 Stainless Steel Murrays Part# 001-5273 Long-wearing, weight-saving, hollow stainless rudder pins with strong, .065" wall provide reduced wear and the best long-term fit. These rudder pins measure 3/8" x 10-1/4" end-to-end with a hole at each end. They will fit Nacra, Prindle and Hobie® 21. Cotter pins are included. These pins are a replacement for Hobie® factory item #40880011 (sold individually). Sold in pairs
    NACRA/PRINDLE AND H21 SS RUDDER PIN
    Murrays Sports
    PRINDLE JIB HALYARD WITH SISTER CLIPS
    Murrays Sports
    Right Rear Crossbar End Cap Murrays Part# 56-3902 Prindle Right Rear Crossbar End Cap P19, 18-2 is a right rear crossbar end cap for Prindle 19 and 18-2. Performance Sports factory item# 3902
    PRINDLE RIGHT REAR CROSSBAR END CAP
    NACRA
    Front Crossbar End Cap Murrays Part# 56-2902 The Prindle Front Crossbar End Cap is for the front crossbar of all Prindles fits both right and left sides. Please specify silver or black and we will do our best to accommodate your selection Nacra Sailing factory item# 30394
    PRINDLE FRONT CROSSBAR END CAP
    NACRA
    Quick Release Deluxe Pin 1/4 X 1.5 with Lanyard Murrays Part# 18-4M150L This quick release pin features a push button on the top that releases 2 spring-loaded balls at the tip that secure the pin in place. This pin includes a lanyard to help prevent loss of pin. Uses: Hobie 18 mast hinge pin, Compare to Hobie part#P 20307 PIN, QR 1/4 X 1-1/2 CUP Upgrade for Hobie 8020181, 8020180, 8020431, 8020430, 8020420, 8020421
    QUICK RELEASE DELUXE PIN 1/4 X 1-1/2" WITH LANYARD
    Misc
    Rudder Pin Nacra, Prindle and H21 (Aluminum) Murrays Part# 001-5272 Aluminum rudder pins for Nacra, Prindle and Hobie® 21 measure 3/8" x 10-1/4" end-to-end, with hole at each end. Cotter pins are included. Sold in pairs
    NACRA/PRINDLE AND H21 ALUMINIUM RUDDER PIN
    Murrays Sports
    Spreader Bar Screw (Fine Threads) Murrays Part# 56-9851 Black, fine-threaded screw (20/inch) fits newer Nacra cats, but may require fine-threaded forward spreader bar (#56-9844) and aft spreader bar (#56-9843) to ensure compatibility with older Nacras and Prindle 18, 18.2 and 19. Nacra Sailing factory item# 30337
    NACRA SPREADER BAR SCREW (FINE THREADS)
    NACRA
    PRINDLE DYNEEMA RACE TRAMP LINE KIT
    Murrays Sports
    Out of Stock
    PRINDLE RUDDER REBUILD KIT
    Murrays Sports
    DACRON INSIGNIA CLOTH - BLACK
    Murrays Sports
    Rudder Pull Up/Down Kit Prindle Murrays Part# 001-1180 Replacement handles and ropes to pull your rudders up and down on all Prindle models.
    PRINDLE RUDDER PULL UP/ DOWN KIT
    Murrays Sports
    Mast Base Hinge Plate Murrays Part# 56-6816 Mast base hinge plate for Prindle 18, 18-2 and 19 Performance Sports factory item# 6816
    PRINDLE MAST BASE HINGE PLATE
    NACRA
    GOOSENECK 'U' BRACKET Murrays Part# 56-7810 Prindle Gooseneck 'U' Bracket Gooseneck "U" bracket fits Nacra 5.2 and all Prindles. Nacra Sailing factory item# 30980
    PRINDLE/NACRA GOOSENECK 'U' BRACKET
    NACRA
    Out of Stock
    PRINDLE TILLER CROSSBAR END CASTING
    Murrays Sports
    Hobie Shroud Adjuster Covers 11″ Pair are vinyl covers that protect the crew from metal shroud adjusters and can prevent de-masting by protecting the split rings. Includes two adjuster covers, one for each side of the boat. Available in white and black. Compatible with al beach cats: Nacra, Prindle, A-Cat, Dart, Sol Cat, G-Cat...
    11" SHROUD ADJUSTER COVERS
    Hobie
    Half Round Load Spreader Murrays Part# 56-4019 This component is installed into the head of the rudder blade to anchor the rudder locking pin. The Prindle Half Round Load Spreader is for rudder system on all Prindles. Prindle Part# 4019 Nacra sailing factory item# 30973
    PRINDLE HALF ROUND LOAD SPREADER
    NACRA
    Ronstan 5/16 bow with hole shackle RF638 - Hobie 20700001 and SP150081
    RONSTAN 5/16" BOW SHACKLE WITH HOLE
    Ronstan
    PRINDLE EXTENDED GUDGEON
    NACRA
    Tiller Rudder Stiffening Kit: Prindle Murrays Part# 001-5141 Spring-loaded tiller connection with contoured spacers tightens the hinge connection on Prindles. Six plastic shims reduce slop between rudders and castings
    PRINDLE TILLER AND RUDDER STIFFENING KIT
    Murrays Sports
    Batten Caps Leech Adjustable Prindle 16 Murrays Part#012-6003 No more knots at the trailing edge. These leech batten caps adjust sail shape in seconds without tying and untying knots. Release tension to prolong sail shape and life. This Perfect Pocket kit by Tren Tec includes 9 batten caps for Prindle 16 and pre-cut line. Tren Tec adjustable batten caps for Prindle catamaran mainsails. Leech caps are used on the trailing edge of the sail. Sold in packages of 9, includes batten tie lines.
    PRINDLE 16 ADJUSTABLE BATTEN LEECH CAPS (9)
    Tren-Tec
    ELONGATED TRAPEZE RING Large trapeze ring made of solid 316 stainless steel for strength and longevity. AKA: dog bone, harness ring, harness loop, trap ring, trapeze ring.  Hobie part number 2002, compare to Hobie part number 2001 Length: 7-1/2"
    ELONGATED TRAPEZE RING
    Misc
    SMALL BLOCK W/REMOVABLE SHEAVE This small block is used on trapeze adjustment systems where the removable sheave enables installation without cutting wires. Specifications: 1-3/16" removable sheave, Teflon® bearing and 5/16" line capacity. Hobie item #3103
    SMALL BLOCK W/REMOVABLE SHEAVE This small block is used on trapeze adjustment systems where the removable sheave enables installation without cutting wires. Specifications: 1-3/16" removable sheave, Teflon® bearing and 5/16" line capacity. Hobie item #3103
    SMALL BLOCK WITH REMOVABLE SHEAVE
    Murrays Sports
    The Tramp Line Kit: When lacing your trampoline, line offers a longer-lasting option over shock cord and is the better choice for sailors who prefer a very tight tramp. As the line stretches slightly over time, sailors can re-tension the tramp lacing to their liking. The line in this kit is black, abrasion-resistant, 8-strand low stretch. #001-2246 for Prindle 15, 16, 18 or Escape includes two 1/8" x 11' lengths and one 3/16" x 22'. #001-2248 for Prindle 18.2 or 19 includes two 19-foot lengths of
    PRINDLE TRAMP LINE KIT
    Murrays Sports
    Narrow Gudgeon Murrays Part# 56-1011 Narrow gudgeon fits Nacra 5.0, 5.7, 6.0 and Prindle 18-2 and 19 Nacra Sailing factory item# 300007
    PRINDLE/NACRA NARROW GUDGEON
    NACRA
    Shroud Stay Adjuster 7 Hole Murrays Part# 25-3310 Stainless steel shroud adjuster with seven 1/4" holes. ​Use #22-9802 clevis pin at top and #22-9808 at bottom. Fits: H14/16/18/20, Wave and Getaway. Compare to Hobie Part# 20830010
    SHROUD STAY ADJUSTER 7-HOLE
    Murrays Sports
    Prindle split rings and clevis pin kit, mast hinge pin
    PRINDLE PINS & RINGS KIT
    Murrays Sports
    Murrays Part# 001-0062 Replacement tiller yoke assembly for all hiking sticks sold by Murrays. Used to connect the tiller extension to the tiller crossbar. Includes two contoured spacers that provide a solid platform for the yoke to sit on. Compare to Hobie Cat® Tiller yoke assembly #3205 or NACRA connection part tiller/joystick #31072 Applications: All Hobies and Prindles Tiller Yoke Assembly: 1
    TILLER YOKE ASSEMBLY WITH SPACERS
    Murrays Sports
    Diamond Tang 3-Hole Bottom Murrays Part# 56-6813 The Prindle Diamond Tang 3-Hole (Bottom) is a 3-hole lower tang for diamond wire is for Prindle 18, 18-2 and 19. Performance Sailing factory item #6813; Nacra Sailing #31444.
    PRINDLE DIAMOND TANG 3-HOLE BOTTOM
    NACRA
    Nacra Crossbar Bolt Chip Murrays Part# 56-2510 The Nacra Crossbar Bolt Chip is for beam mounting on Prindles and Nacras. Nacra Sailing factory item# 30069 Prindle item# 2510
    NACRA CROSSBAR BOLT CHIP
    NACRA
    Spreader Tip Plate Murrays Part# 56-9842 Spreader tip plate for all Nacras and Prindle 18, 18.2 and 19. Nacra Sailing factory item# 30316
    NACRA SPREADER TIP PLATE
    NACRA
    DIAMOND WIRE ROLLER
    Misc
    Trap Shock Cord: Nacra, Prindle, Sol Cat and Getaway Murrays Part# 001-8019 A trapeze shock cord is an absolute necessity because it keeps the trapeze system in place and ready for hook-up. One hook connects to either the thimble on the trapeze wire or the adjustment line, then runs under the tramp and connects to the other side in the same location. A plastic carbine hook is installed on one end only; the other hook is included to be installed after the shock cord is put on the boat. Cord is 1/4" d
    NACRA/PRINDLE/SOL CAT AND GETAWAY TRAP SHOCK CORD
    Murrays Sports
    Quick Release Detent Pin 1/4 X 3" Murrays Part# 18-4D300 Economical quick release pin has a spring-loaded ball that exerts sufficient pressure to help avoid accidental release. Measurements are 1/4" diameter x 3" maximum grip length (distance from the shoulder to the locking ball bearings). Uses: - Use as mast step pin on Hobie® 21 and Prindle 16/18/18-2/19 cats. Compare to Hobie part # 8020501
    Quick Release Detent Pin 1/4 X 3" Murrays Part# 18-4D300 Economical quick release pin has a spring-loaded ball that exerts sufficient pressure to help avoid accidental release. Measurements are 1/4" diameter x 3" maximum grip length (distance from the shoulder to the locking ball bearings). Uses: - Use as mast step pin on Hobie® 21 and Prindle 16/18/18-2/19 cats. Compare to Hobie part # 8020501
    QUICK RELEASE DETENT PIN 1/4 X 3"
    Misc
    3-Hole Pad Kit Murrays Part# 001-0110 This base kit is for Harken®, Hobie® or Murray 360 cleats without swivel base adapters. Kit includes one 3-hole base, one swivel base adapter (#25-3001), plus three #10 FHSMS (#19-1626). Ronstan swivel 360 cleats include swivel base adapters, so this kit is not necessary. Fits Hobie® or Prindle elliptical crossbar.
    3-HOLE PAD KIT
    Murrays Sports
    Dolphin Striker Casting Murrays Part# 56-2009 Performance Sports factory dolphin striker casting for all Prindle Cats
    Prindle part numbers 2505, 2009 and 2009C
    PRINDLE DOLPHIN STRIKER CASTING
    NACRA
    Hobie Cat #80550005 Main sail batten pocket protector kit. Hobie, Nacra, Prindle.
    MAIN SAIL POCKET PROTECTOR KIT
    Murrays Sports
    Recently viewed