All Prindle 15 Parts

98 products

    98 products
    Out of Stock
    TILLER X-BAR END CAST PRINDLE
    Murrays Sports
    6" Access Port with Lip Murrays Part# 001-4210WH The 6" Access Port with Lip is standard on the Hobie 18 and newer Prindle cats and it is an excellent upgrade for older Prindles. Ports can be installed on any flat deck, including kayaks, where there is 8-1/2" of flat surface available. These ports come with the inner lip so they are compatible with the 6"cat bag. Does not include hardware, hardware options shown in the related items section below. White port is Murrays #01-4210WH. Compare to Hobie Cat® #
    6" ACCESS PORT WITH LIP
    Sailing
    Half Round Load Spreader Murrays Part# 56-4019 This component is installed into the head of the rudder blade to anchor the rudder locking pin. The Prindle Half Round Load Spreader is for rudder system on all Prindles. Prindle Part# 4019 Nacra sailing factory item# 30973
    HALF ROUND LOAD SPREADER
    NACRA
    Ronstan 5/16 bow with hole shackle RF638 - Hobie 20700001 and SP150081
    RONSTAN 5/16" BOW SHACKLE WITH HOLE
    Ronstan
    10 Hole Hobie shroud adjuster
    SHROUD STAY ADJUSTER 10-HOLE
    Misc
    Tiller Rudder Stiffening Kit: Prindle Murrays Part# 001-5141 Spring-loaded tiller connection with contoured spacers tightens the hinge connection on Prindles. Six plastic shims reduce slop between rudders and castings
    PRINDLE TILLER AND RUDDER STIFFENING KIT
    Murrays Sports
    Batten Caps Leech Adjustable P16 Murrays Part#012-6003 No more knots at the trailing edge. These leech batten caps adjust sail shape in seconds without tying and untying knots. Release tension to prolong sail shape and life. This Perfect Pocket kit by Tren Tec includes 9 batten caps for Prindle 16 and pre-cut line. Tren Tec adjustable batten caps for Prindle catamaran mainsails. Leech caps are used on the trailing edge of the sail. Sold in packages of 9, includes batten tie lines.
    P-16 ADJUSTABLE BATTEN LEECH CAPS (9)
    Tren-Tec
    H14/16 Main Halyard Hook Murrays Part# 25-3330 The main halyard hook is used on the Hobie 14, Hobie 16, Wave, Getaway, Prindles, Sol Cats and Nacras that use a wire halyard. Use two 6-4 rivets (#19-5031) and two casings (#19-5020) for installation. Hobie part# 10680000
    H-14/16 MAIN HALYARD HOOK
    Hobie
    The Tramp Line Kit: Prindle- When lacing your trampoline, line offers a longer-lasting option over shock cord and is the better choice for sailors who prefer a very tight tramp. As the line stretches slightly over time, sailors can re-tension the tramp lacing to their liking. The line in this kit is black, abrasion-resistant, 8-strand low stretch. #001-2246 for Prindle 15, 16, 18 or Escape includes two 1/8" x 11' lengths and one 3/16" x 22'. #001-2248 for Prindle 18.2 or 19 includes two 19-foot lengths of
    TRAMP LINE KIT
    Murrays Sports
    Harken 22mm Block Murrays Part# 28-0224 This Harken ball bearing micro single block with stainless side plates is a small block with high load capabilities. It is a premium quality block for your trapeze return system.
    HARKEN 22MM BLOCK
    Harken
    Ronstan Stainless Steel Bow Shackle, 5/16" Pin, Coined Head with Hole Murrays Part# 21-0636 The Ronstan 5/16 Bow Shackle has 5/16" diameter pin. Compare to Hobie® #20700001 and SP150081. Standard all Hobie, Nacra and Prindle catamarans to attach the standing rigging to the mast tang.
    RONSTAN 5/16" BOW SHACKLE
    Ronstan
    Rudder Gudgeon Murrays Part# 56-1016 Rudder gudgeon for Prindle 15, 16 and 18 Nacra Sailing factory item# 30993
    RUDDER GUDGEON
    NACRA
    SMALL BLOCK W/REMOVABLE SHEAVE This small block is used on trapeze adjustment systems where the removable sheave enables installation without cutting wires. Specifications: 1-3/16" removable sheave, Teflon® bearing and 5/16" line capacity. Hobie item #3103
    SMALL BLOCK W/REMOVABLE SHEAVE This small block is used on trapeze adjustment systems where the removable sheave enables installation without cutting wires. Specifications: 1-3/16" removable sheave, Teflon® bearing and 5/16" line capacity. Hobie item #3103
    SMALL BLOCK WITH REMOVABLE SHEAVE
    Murrays Sports
    Prindle split rings and clevis pin kit, mast hinge pin
    PRINDLE PINS & RINGS KIT
    Murrays Sports
    Murrays Part# 001-0062 Replacement tiller yoke assembly for all hiking sticks sold by Murrays. Used to connect the tiller extension to the tiller crossbar. Includes two contoured spacers that provide a solid platform for the yoke to sit on. Compare to Hobie Cat® Tiller yoke assembly #3205 or NACRA connection part tiller/joystick #31072 Applications: All Hobies and Prindles Tiller Yoke Assembly: 1
    TILLER YOKE ASSEMBLY WITH SPACERS
    Murrays Sports
    Ronstan Plastic Drain Plug with Chrome Brass Housing, 15/16" Hole Murrays Part# 21-0737 This lightweight and inexpensive plug features a molded recess in the base that traps sealant (sold separately) in place, providing a more watertight seal. Nylon plug is UV-stabilized. Retaining legs keep drain plug from falling out of hole when unscrewed. Includes chromed brass housing (body) and gasket.
    RONSTAN PLASTIC DRAIN PLUG WITH CHROME BRASS HOUSING, 15/16" HOLE
    Ronstan
    Nacra Crossbar Bolt Chip Murrays Part# 56-2510 The Nacra Crossbar Bolt Chip is for beam mounting on Prindles and Nacras. Nacra Sailing factory item# 30069 Prindle item# 2510
    NACRA CROSSBAR BOLT CHIP
    NACRA
    ELONGATED TRAPEZE RING Large trapeze ring made of solid 316 stainless steel for strength and longevity. AKA: dog bone, harness ring, harness loop, trap ring, trapeze ring.  Hobie part number 2002, compare to Hobie part number 2001 Length: 7-1/2"
    ELONGATED TRAPEZE RING
    Murrays Sports
    Out of Stock
    END CAP (SLOTTED) TILLER ARM
    Murrays Sports
    4" ALUMINUM BAR FOR BOW TANG Bow tang support rod for Prindle catamarans. Aluminum bar for bow tang on Prindle 15, 16 and 18 is Nacra Sailing factory item #30387.
    4" ALUMINUM BAR FOR BOW TANG
    NACRA
    Trap Shock Cord: Nacra, Prindle, Sol Cat and Getaway Murrays Part# 001-8019 A trapeze shock cord is an absolute necessity because it keeps the trapeze system in place and ready for hook-up. One hook connects to either the thimble on the trapeze wire or the adjustment line, then runs under the tramp and connects to the other side in the same location. A plastic carbine hook is installed on one end only; the other hook is included to be installed after the shock cord is put on the boat. Cord is 1/4" d
    NACRA, PRINDLE, SOL CAT AND GETAWAY TRAP SHOCK CORD
    Murrays Sports
    Quick Release Detent Pin 1/4 X 3" Murrays Part# 18-4D300 Economical quick release pin has a spring-loaded ball that exerts sufficient pressure to help avoid accidental release. Measurements are 1/4" diameter x 3" maximum grip length (distance from the shoulder to the locking ball bearings). Uses: - Use as mast step pin on Hobie® 21 and Prindle 16/18/18-2/19 cats. Compare to Hobie part # 8020501
    Quick Release Detent Pin 1/4 X 3" Murrays Part# 18-4D300 Economical quick release pin has a spring-loaded ball that exerts sufficient pressure to help avoid accidental release. Measurements are 1/4" diameter x 3" maximum grip length (distance from the shoulder to the locking ball bearings). Uses: - Use as mast step pin on Hobie® 21 and Prindle 16/18/18-2/19 cats. Compare to Hobie part # 8020501
    QUICK RELEASE DETENT PIN 1/4 X 3"
    Misc
    Ronstan 3/16 Twisted D Shackle Murrays Part# 21-0628 Stainless steel twisted D-shackle has a 3/16" pin.
    RONSTAN 3/16" TWISTED D SHACKLE
    Ronstan
    1/4 bow shackle Ronstan Part# RF635 Compare to Hobie® #10700000, 10700010 and SP150061, 27900146,
    1/4" Bow Shackle Ronstan PN RF635
    RONSTAN 1/4" BOW SHACKLE
    Ronstan
    Flat Head Machine Screw 5/16 X 5" Murrays Part# 56-F105 Allen Head Machine Screw 5/16 X 5" Originally this was a flat head screw. Compare to Performance Sports factory item# F105
    FLAT HEAD MACHINE SCREW 5/16-18 x 5"
    NACRA
    Dolphin Striker Casting Murrays Part# 56-2009 Performance Sports factory dolphin striker casting for all Prindle Cats
    DOLPHIN STRIKER CASTING
    NACRA
    Hobie Cat #80550005 Main sail batten pocket protector kit. Hobie, Nacra, Prindle.
    MAIN SAIL POCKET PROTECTOR KIT
    Murrays Sports
    Rear Hex Bolt 5/16 X 5.75" Outboard Bolt Murrays Part# 56-F141 5/16" x 5-3/4" hex cap bolt is for Prindle rear crossbar. Performance Sports Factory item# F141
    REAR HEX BOT 5/16 X 5.75" OUTBOARD BOLT
    NACRA
    Bow Tang Murrays Part# 56-1810 Bow tang for Prindle 15, 16, 18 and Escape Nacra Sailing factory item# 30386
    BOW TANG
    NACRA
    Mast Base Hinge Murrays Part# 56-6516 Mast base hinge plate for Prindle 15 Performance Sports Factory item# 6516
    MAST BASE HINGE
    NACRA
    NACRA and Prindle Rudder Spring Murrays Part# 56-4016 The NACRA and Prindle Rudder Spring is the rudder spring for all Prindle and most newer Nacras (Late Model US boats, Inters and all European NACRA boats) is Nacra Sailing factory item #30418. Fits Nacra 460, Nacra 500, Nacra 570, Nacra 16, Nacra 17, Nacra F18 Infusion, Nacra F20 Carbon and all Inters.
    RUDDER SPRING
    NACRA
    Rudder Lock Release Strap Murrays Part# 56-4010 This is one of two plates used in each rudder assembly on a Prindle beach cat. This is part of the internal assembly that moves up and down as part of the rudder pull up/down system. The Prindle Rudder Lock Release Strap is works on all Prindles. Nacra sailing factory item# 30415 Prindle Part# 4010
    RUDDER LOCK RELEASE STRAP
    NACRA
    OWNERS MANUAL P15/16/18
    Murrays Sports
    Hex Bolt 3/8 X 4.25" Murrays Part# 56-F142 3/8" x 4-1/4" hex head bolt is for Prindle front crossbar Performance Sports factory item# F142
    HEX BOLT 3/8 X 4.25"
    NACRA
    Universal Drain Plug for most Hobie, Nacra and Prindle Catamarans which includes a gasket and fits most Hobie, Nacra and Prindle catamarans. Hobie part number 10091000
    Hobie drain plug 10091000 Hobie 18
    DRAIN PLUG WITH GASKET
    Misc
    Replacement Sheave Prindle Rudder Upper Ronstan PN RF1741 Replacement sheave for upper part of rudder casting on all models of Prindle catamarans. Replacement for Performance Sports item #4009. 1/4" wide x 3/4" diameter, 1/4" hole.
    ILLUSTRATED PRNDLE RUDDER PARTS LIST
    RONSTAN 19MM ACETAL SHEAVE, 6MM WIDTH
    Ronstan
    Bolt Hex Head 5/16-18 X 4.50" (Stainless Steel) Murrays Part# 19-2237 Stainless steel hex head bolt for Prindle mast rotation control arm. Use #19-2520 nylock nut. This bolt is a replacement for item #56-F110 Comparable to Hobie Part# 8040211
    BOLT HEX HEAD 5/16-18 X 4.50" SS
    Misc
    Clevis Pin 1/4 X 3/4" Murrays Part# 56-4012 The Clevis Pin 1/4 X 3/4" is used on Prindle rudders, Nacra mast head sheave and as Nacra/Prindle shroud pin. Prindle Part# 4012
    CLEVIS PIN 1/4 X 3/4"
    NACRA
    1/4 X 1-3/8" Clevis Pin Murrays Part# 22-9804 Stainless steel clevis pin. Measurement is 1/4" diameter x 1-3/4" grip length (shoulder to the split ring hole). This pin replaces #56-7809, gooseneck clevis pin for Nacra 5.2 and all Prindles. Prindle Part# 6004 Comparable to Hobie Cat® Part# 8020431
    1/4 X 1-3/8" CLEVIS PIN
    Misc
    Upper Rudder Roller Murrays Part# 56-4009 This plastic spacer/ roller is used in the locking mechanism of Prindle Rudder systems. It is also used as a boom roller.
    UPPER RUDDER ROLLER
    NACRA