Prindle 19 Mast Parts

11 products

    Parts for your Prindle 19 Mast

    11 products
    MAST BASE CASTING
    NACRA
    Harken Sail Chafe Protector Murrays Part# 28-0285 Harken's Sail Chafe Protector Set replaces the diamond wire rollers to protect the jib from chafing on the diamond wire spreader. The split rollers are pre-drilled to fit up to 3/16" wire. Each 2-3/4"-diameter (70mm) protector has two pieces that snap together for easy installation. Used on Hobie 18, Hobie 20, Prindle 18.2, Prindle 19, Nacra 15, 17, 18, Inter 20, F18
    HARKEN SAIL CHAFE PROTECTOR (2)
    Harken
    Gooseneck Base Fitting Murrays Part# 56-7807 The Prindle Gooseneck base fitting attaches to mast of Prindle 15, 16, 18, 18-2 and 19. Nacra Sailing factory item# 30202
    GOOSNECK BASE FITTING
    NACRA
    Ronstan 5/16 bow with hole shackle RF638 - Hobie 20700001 and SP150081
    RONSTAN 5/16" BOW SHACKLE WITH HOLE
    Ronstan
    Prindle split rings and clevis pin kit, mast hinge pin
    PRINDLE PINS & RINGS KIT
    Murrays Sports
    DIAMOND WIRE ROLLER
    Misc
    Quick Release Detent Pin 1/4 X 3" Murrays Part# 18-4D300 Economical quick release pin has a spring-loaded ball that exerts sufficient pressure to help avoid accidental release. Measurements are 1/4" diameter x 3" maximum grip length (distance from the shoulder to the locking ball bearings). Uses: - Use as mast step pin on Hobie® 21 and Prindle 16/18/18-2/19 cats. Compare to Hobie part # 8020501
    Quick Release Detent Pin 1/4 X 3" Murrays Part# 18-4D300 Economical quick release pin has a spring-loaded ball that exerts sufficient pressure to help avoid accidental release. Measurements are 1/4" diameter x 3" maximum grip length (distance from the shoulder to the locking ball bearings). Uses: - Use as mast step pin on Hobie® 21 and Prindle 16/18/18-2/19 cats. Compare to Hobie part # 8020501
    QUICK RELEASE DETENT PIN 1/4 X 3"
    Misc
    P18/19 Ronstan Mast Head Base Sheave Murrays Part# 56-6804 Replacement sheave for mast base on Prindle 15, 18, 18.2, 19 and Nacra 2003 and later mast head. Sheave measures 1-1/8" diameter x 3/8" wide. Please note that this item replaces #6803 that is no longer available.
    P-18/19 RONSTAN MAST HEAD SHEAVE
    Ronstan
    Bolt Hex Head 5/16-18 X 4.50" (Stainless Steel) Murrays Part# 19-2237 Stainless steel hex head bolt for Prindle mast rotation control arm. Use #19-2520 nylock nut. This bolt is a replacement for item #56-F110 Comparable to Hobie Part# 8040211
    BOLT HEX HEAD 5/16-18 X 4.50" SS
    Misc
    Stainless steel clevis pin. Measurement is 1/4" diameter x 5/8" grip length. Hobie part number 8020361, 8020381 and 8020380.
    1/4 X 5/8" CLEVIS PIN
    Misc
    Used for tiller connection on Hobie Cats®. The stainless 1/4-20 stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Equivalent to Hobie #8050111. Also Equivalent to Nacra/Prindle F123 gudgon nut for all Prindle and older Nacras. Applications: Hobie 18 / H18: Bow Tang Nut Qty: 6 Rudder Adjustment: 1 Hobie Getaway: Forestay Yoke Nut
    NYLOCK NUT 1/4-20 SS
    Misc