Hobie Wave Rear Crossbar Parts

15 products

    Rear Crossbar Parts for your Hobie Wave.

    15 products
    Rear Crossbar Wave
    Hobie
    Aluminum Adjustable tiller extension for Hobie, Nacra and Prindle catamarans. Compare to Hobie 20550001 Hobie hot stick
    ALUMINUM TILLER EXTENSION 50"-95"
    Murrays Sports
    Out of Stock
    END CAP AFT WAVE BLACK
    Hobie
    Rivet MSP 6-10 3/16 X 5/8" PH Murrays Part# 19-5023 Rounded pan head 3/16" x 5/8" Monel rivet. Compare to Hobie Cat® Part# 8010121
    RIVET MSP 6-10 3/16 X 5/8" PH
    Hobie
    Small Fairlead: 1-1/4 X 1/2 Murrays Part# 23-0921 Stainless steel fairlead measurements: A = 1-1/4" (31.4mm) between holes center-to-center B = 1/2" (12.7mm) height C = 3/16" (5mm) hole diameter
    RONSTAN SMALL FAIRLEAD: 1-1/4 X 1/2
    Ronstan
    Bolt Hex Head 5/16-18 X 1.5" Murrays Part# 19-2229 Use this stainless steel, 5/16-18 x 1-1/2" hex head bolt as beam strap bolt for Nacra. Substitute for Nacra Sailing factory item #30358. This bolt is also used to hold the cam stop plate on a Hobie Rudder Upper casting. Replaces Hobie Cat® Part# 8040301 and Murrays Part# 56-F164
    BOLT HEX HEAD 5/16-18 X 1.5"
    Misc
    Sealed Rivet CCP 6-8 (3/16 X 1/2) Murrays Part# 19-5033S Sealed rivets have a sealed end that does not require rivet casings to make them water tight. One and done, no casing needed, just insert and pop as you would a normal rivet, and your hole will be sealed. Sealed Stainless steel 3/16" x 1/2" rounded pan head rivet. Compare to Hobie Cat® #8011231 Rivet and Hobie Cat® #8011291 rivet casing.
    RIVET CCP SEALED 6-8 (3/16 X 1/2)
    Misc
    RIVET MCP 6-8 3/16x1/2" PH Murrays Part# 50-8011231 Hobie® factory 6-8 heavy duty rivet requires a rivet tool for installation. 3/16" x 1/2" pan head. Fits Hobie Getaway Eyelet Post. Fits Hobie 20 Eyelet Post. Mounts Wave Mast Step Hobie part number 8011231
    RIVET MCP 6-8 3/16x1/2" PH
    Hobie
    Nut Nylock 5/16-18 Stainless Steel Murrays Part# 19-2520 5/16-18 nylock nut is used on Hobie® rudders. The stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Compare to Hobie Cat® item #8050311 and 8050321 shroud anchor pin nut Used with Hobie Getaway Bow Tang Bolt
    NUT NYLOCK 5/16-18 (SS)
    Misc
    3/16 - 1/4" Split Ring Murrays Part# 22-9492 Stainless steel split ring (ring ding) for 3/16″-1/4″ diameter clevis pin. This is the standard size Hobie split ring used all over the boats, most commonly on the shrouds, forestay and roller furler Medium Split ring Dimensions: 5/8″ Diameter Material: 316 Stainless steel. This is the most common size Split ring on Hobie, Nacra and Prindle Catamarans. 20860000 Medium Clevis Ring.
    SPLIT RING 3/16-1/4"
    Misc
    Rivet CCP 6-4 (3/16 X 1/4) Murrays Part# 19-5031 Stainless steel 3/16" x 1/4" rounded pan head rivet. Compare to Hobie Cat® #8010181. This is a common rivet used on many extrusions. Hobie, Nacra, Prindle masts and booms. Pair with a rivet casing to seal the rivet hole when used on masts. All Hobie mast hounds, tangs, heads, and cheek blocks. Used with Hobie Getaway Bow Spreader Plates Used on Hobie Getaway FWD and REAR Crossbar Stop Plates
    RIVET CCP 6-4 (3/16 X 1/4)
    Misc
    1/2 BALL (NYLON) - Hobie half round washer spacer tiller connector - Hobie part number 11510000 HOBIE HALF SPHERE TILLER CONNECTOR
    NYLON 1/2" BALL
    Murrays Sports
    Out of Stock
    FIBER TENDON SCREW
    Misc
    Washer 5/16 x 3/4 Flat SS Murrays Part# 50-8080671 EZ Loc Rudder Assembly Lower Bolt Washer for Hobie Bravo, Getaway and Wave Hobie Part# 8080671
    Washer SS 5/16 x 3/4 Flat
    Hobie
    NUT SQUARE 10-32 Murrays Part# 50-8051301 Hobie® factory replacement stainless steel 10-32 square nut can be used when mounting downhaul/halyard cleat on Hobie® 14 or 16. Also can be used for mounting H17 trampoline eye straps. Use 19-2910 screw. Hobie Part# 8051301
    NUT SQUARE 10-32
    Hobie