Hobie Wave Front Crossbar Parts

16 products

    Front Crossbar Parts for your Hobie Wave

    16 products
    Wave Front Crossbar 1438up
    Hobie
    MAST BEARING H-14/16 (100-PKG)
    Murrays Sports
    Out of Stock
    MAST STEP H14/WAVE BK
    Hobie
    Out of Stock
    WAVE MAST STEP SN 1438 UP
    Hobie
    Mast Ball H17 Wave Murrays Part# 50-50212301 Hobie factory replacement mast ball for Hobie® 17 and Wave. Ball measures 1-1/2" diameter with a 9/16"-18 threaded hole. This ball can also be glued for use on Trac 16.
    MAST BALL H-17 & WAVE
    Hobie
    The Murrays Pins & Rings Kit: Hobie Wave + Getaway includes the most often used spare clevis pins and split rings for the Hobie Wave and Hobie Getaway. Compare to Hobie Part # 30302
    Pins & Rings Kit: Hobie Wave, Getaway
    Murrays Sports
    Hobie Wave Mast Step Post (Threaded) Murrays Part# 50-38170001 This part is used on the Hobie Wave to connect the mast ball to the mast step casting on the front crossbar. The older waves utilize an H14 mast step casting. Hobie Part# 38170001
    HOBIE WAVE MAST STEP POST (THREADED)
    Hobie
    3-HOLE PAD KIT: HOBIE AND PRINDLE
    Murrays Sports
    Hobie 16 mast bearings. Teflon mast chips, Hobie part number 11110005
    Hobie mast chips - 11110005
    MAST BEARING H-14/16 (3-PKG)
    Murrays Sports
    Small Fairlead: 1-1/4 X 1/2 Murrays Part# 23-0921 Stainless steel fairlead measurements: A = 1-1/4" (31.4mm) between holes center-to-center B = 1/2" (12.7mm) height C = 3/16" (5mm) hole diameter
    RONSTAN SMALL FAIRLEAD: 1-1/4 X 1/2
    Ronstan
    Sealed Rivet CCP 6-8 (3/16 X 1/2) Murrays Part# 19-5033S Sealed rivets have a sealed end that does not require rivet casings to make them water tight. One and done, no casing needed, just insert and pop as you would a normal rivet, and your hole will be sealed. Sealed Stainless steel 3/16" x 1/2" rounded pan head rivet. Compare to Hobie Cat® #8011231 Rivet and Hobie Cat® #8011291 rivet casing.
    RIVET CCP SEALED 6-8 (3/16 X 1/2)
    Misc
    RIVET MCP 6-8 3/16x1/2" PH Murrays Part# 50-8011231 Hobie® factory 6-8 heavy duty rivet requires a rivet tool for installation. 3/16" x 1/2" pan head. Fits Hobie Getaway Eyelet Post. Fits Hobie 20 Eyelet Post. Mounts Wave Mast Step Hobie part number 8011231
    RIVET MCP 6-8 3/16x1/2" PH
    Hobie
    Nut Nylock 5/16-18 Stainless Steel Murrays Part# 19-2520 5/16-18 nylock nut is used on Hobie® rudders. The stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Compare to Hobie Cat® item #8050311 and 8050321 shroud anchor pin nut Used with Hobie Getaway Bow Tang Bolt
    NUT NYLOCK 5/16-18 (SS)
    Misc
    Rivet CCP 6-4 (3/16 X 1/4) Murrays Part# 19-5031 Stainless steel 3/16" x 1/4" rounded pan head rivet. Compare to Hobie Cat® #8010181. This is a common rivet used on many extrusions. Hobie, Nacra, Prindle masts and booms. Pair with a rivet casing to seal the rivet hole when used on masts. All Hobie mast hounds, tangs, heads, and cheek blocks. Used with Hobie Getaway Bow Spreader Plates Used on Hobie Getaway FWD and REAR Crossbar Stop Plates
    RIVET CCP 6-4 (3/16 X 1/4)
    Misc
    Out of Stock
    FIBER TENDON SCREW
    Misc
    NUT SQUARE 10-32
    Hobie