Hobie 14 sailboat parts

HOBIE H14 PARTS

250 products

    Hobie 14 sails, rudders, trampolines, rigging and more.

    250 products
    Nut Nylock 5/16-18 Stainless Steel Murrays Part# 19-2520 5/16-18 nylock nut is used on Hobie® rudders. The stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Compare to Hobie Cat® item #8050311 and 8050321 shroud anchor pin nut Used with Hobie Getaway Bow Tang Bolt
    NUT NYLOCK 5/16-18 (SS)
    Misc
    Rivet CCP 6-4 (3/16 X 1/4) Murrays Part# 19-5031 Stainless steel 3/16" x 1/4" rounded pan head rivet. Compare to Hobie Cat® #8010181. This is a common rivet used on many extrusions. Hobie, Nacra, Prindle masts and booms. Pair with a rivet casing to seal the rivet hole when used on masts. All Hobie mast hounds, tangs, heads, and cheek blocks. Used with Hobie Getaway Bow Spreader Plates Used on Hobie Getaway FWD and REAR Crossbar Stop Plates
    RIVET CCP 6-4 (3/16 X 1/4)
    Misc
    1/2 BALL (NYLON) - Hobie half round washer spacer tiller connector - Hobie part number 11510000 HOBIE HALF SPHERE TILLER CONNECTOR
    Tiller Connection Kit Murrays Part# 001-2061 The Murrays Tiller Connection Kit assures consistent rudder alignment through the full rudder sweep. Spring-loaded half balls and contoured spacers take the slop out of the tiller-to-crossbar connection on Hobie Cats. Racing class legal. Each kit contains 2 connectors to join the tiller crossbar to the tiller arms. Compare to Hobie Cat® #3052. Applications:; Hobie 14, 16, 17, 18, 18SX
    NYLON 1/2" BALL
    Murrays Sports
    Hobie Drain Plug Screw Murrays Part# 50-8031731 This screw is used to hold the rudder housing in the back of many of the Hobie Beach cats. H14, H16, H17, H18 Hobie Part# 8031731
    HOBIE DRAIN PLUG SCREW
    Hobie
    Used for tiller connection on Hobie Cats®. The stainless 1/4-20 stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Equivalent to Hobie #8050111. Also Equivalent to Nacra/Prindle F123 gudgon nut for all Prindle and older Nacras. Applications: Hobie 18 / H18: Bow Tang Nut Qty: 6 Rudder Adjustment: 1 Hobie Getaway: Forestay Yoke Nut
    NYLOCK NUT 1/4-20 SS
    Misc
    Screw PHMS #10-32 X 1 Stainless Steel Slot Head Murrays Part# 19-2915 Stainless steel, pan head #10-32 x 1" machine screw with slot is used as dolphin striker screw on all Prindles. Replaces Murrays item #56-F112. Also used in some Hobie Applications, compare to 8030111 Hobie Part. Applications: H18/18 SX/16 and Getaway Tiller Hinge Screw: 2
    SCREW PHMS #10-32 X 1" (SS)
    Misc
    Comptip Cap Plug Murrays Part# 50-8090900 This part is used to seal the hole in the Comptip of a Hobie cat after the expanding foam has been put in. Hobie Part# 8090900
    COMP-TIP CAP PLUG
    Hobie
    NUT SQUARE 10-32 Murrays Part# 50-8051301 Hobie® factory replacement stainless steel 10-32 square nut can be used when mounting downhaul/halyard cleat on Hobie® 14 or 16. Also can be used for mounting H17 trampoline eye straps. Use 19-2910 screw. Hobie Part# 8051301
    NUT SQUARE 10-32
    Hobie
    Out of Stock
    Washer 5/16 X 9/16 Flat Murrays Part# 50-8080181 Hobie Part# 8080181
    WASHER FLAT 5/16 X 9/16"
    Hobie
    Cotter Pin 3/32 X 3/4 Murrays Part# 19-1015 Cotter pins are used on all Hobie, Nacra and Prindle rudder pins. They are used to secure the rudder pins. Compare to Hobie Cat® #8060111. Stainless steel cotter pin measures 3/32" x 3/4".
    COTTER PIN 3/32 X 3/4" SS
    Misc
    Recently viewed