Getaway Front Crossbar Parts

20 products

    Collection includes parts for the Front Crossbar and bow spreader crossbar.

    20 products
    Out of Stock
    Bow Spreader Getaway
    Hobie
    Harken Swivel with Carbo Cam Bullseye Murrays Part# 25-3010 Swivel cam cleats are ideal for main traveler control and up-release jib cleating systems. Cam cleats and fairleads should be selected on the basis of need. Order plastic base pads and flat head screws separately to mount to your front crossbar.
    HARKEN SWIVEL W/CARBO CAM & BULLSEYE
    Harken
    MAST BALL H20/21/Getaway
    Hobie
    The Murrays Pins & Rings Kit: Hobie Wave + Getaway includes the most often used spare clevis pins and split rings for the Hobie Wave and Hobie Getaway. Compare to Hobie Part # 30302
    Pins & Rings Kit: Hobie Wave, Getaway
    Murrays Sports
    BOW TANG H14/16
    Hobie
    Out of Stock
    Getaway Spreader Pole End Cap Murrays Part# 50-37500031 Hobie® factory replacement end cap for Getaway spreader pole Hobie Part# 37500031
    GETAWAY SPREADER POLE END CAP
    Hobie
    RACING MINI CLAM CLEAT
    Clamcleat
    3-HOLE PAD KIT: HOBIE AND PRINDLE
    Murrays Sports
    SCREW 5/16-18 X 2" PHMS-P SS
    Murrays Sports
    Bolt Hex Head 5/16-18 X 2.50" Stainless Steel Murrays Part# 19-2231 Stainless steel rudder bolt for all Hobie® Cats measures 5/16-18 x 2.50".  Used on Hobie Getaway Bow Spreader - Bow Tang Bolt. Rudder bolt for both the upper and lower rudder casting. Compare to Hobie Cat® Part# 8040341
    BOLT HEX HEAD 5/16-18 X 2.50" SS
    Misc
    NUT JAM H21
    Misc
    Rivet CCC 6-6 (3/16 X 3/8) Countersunk Murrays Part# 19-5024 Countersunk stainless steel 3/16" x 3/8" rivet for traveler tracks, etc. Compare to Hobie Part # 8010201. This rivets is what Hobie recommends for both the main traveler tack and the jib traveler track. We also recommend using an 1/8" stop sleeve, part number 002-1041, as a spacer to help you apply pressure on the rivet inside the track, as the track is too narrow for most rivet guns to get far enough inside to apply pressure to the rivet.
    RIVET CCC 6-6 CSK
    Misc
    Sealed Rivet CCP 6-8 (3/16 X 1/2) Murrays Part# 19-5033S Sealed rivets have a sealed end that does not require rivet casings to make them water tight. One and done, no casing needed, just insert and pop as you would a normal rivet, and your hole will be sealed. Sealed Stainless steel 3/16" x 1/2" rounded pan head rivet. Compare to Hobie Cat® #8011231 Rivet and Hobie Cat® #8011291 rivet casing.
    RIVET CCP SEALED 6-8 (3/16 X 1/2)
    Misc
    WASHER 5/8 X 1-5/16 SS
    Misc
    RIVET MCP 6-8 3/16x1/2" PH Murrays Part# 50-8011231 Hobie® factory 6-8 heavy duty rivet requires a rivet tool for installation. 3/16" x 1/2" pan head. Fits Hobie Getaway Eyelet Post. Fits Hobie 20 Eyelet Post. Mounts Wave Mast Step Hobie part number 8011231
    RIVET MCP 6-8 3/16x1/2" PH
    Hobie
    Nut Nylock 5/16-18 Stainless Steel Murrays Part# 19-2520 5/16-18 nylock nut is used on Hobie® rudders. The stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Compare to Hobie Cat® item #8050311 and 8050321 shroud anchor pin nut Used with Hobie Getaway Bow Tang Bolt
    NUT NYLOCK 5/16-18 (SS)
    Misc
    Rivet CCP 6-4 (3/16 X 1/4) Murrays Part# 19-5031 Stainless steel 3/16" x 1/4" rounded pan head rivet. Compare to Hobie Cat® #8010181. This is a common rivet used on many extrusions. Hobie, Nacra, Prindle masts and booms. Pair with a rivet casing to seal the rivet hole when used on masts. All Hobie mast hounds, tangs, heads, and cheek blocks. Used with Hobie Getaway Bow Spreader Plates Used on Hobie Getaway FWD and REAR Crossbar Stop Plates
    RIVET CCP 6-4 (3/16 X 1/4)
    Misc
    Out of Stock
    FIBER TENDON SCREW
    Misc
    Used for tiller connection on Hobie Cats®. The stainless 1/4-20 stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Equivalent to Hobie #8050111. Also Equivalent to Nacra/Prindle F123 gudgon nut for all Prindle and older Nacras. Applications: Hobie 18 / H18: Bow Tang Nut Qty: 6 Rudder Adjustment: 1 Hobie Getaway: Forestay Yoke Nut
    NYLOCK NUT 1/4-20 SS
    Misc
    Screw PHMS #10-32 X 1 Stainless Steel Slot Head Murrays Part# 19-2915 Stainless steel, pan head #10-32 x 1" machine screw with slot is used as dolphin striker screw on all Prindles. Replaces Murrays item #56-F112. Also used in some Hobie Applications, compare to 8030111 Hobie Part. Applications: H18/18 SX/16 and Getaway Tiller Hinge Screw: 2
    SCREW PHMS #10-32 X 1" (SS)
    Misc