Hobie 18 Hull Parts

29 products

    Parts for your Hobie 18 Hull

    29 products
    Harken 57mm Ratchet Block - Swivel, Becket, Cam Cleat
Murrays Part# 28-2139
Harken 57mm jib block is great for use on almost all Hobie Cat, Nacra and Prindle. Carbo Ratchets allow sailors to hand-hold loaded lines and offer balance between holding power and controlled easing.
Specifications
Sheave diameter: 2-1/4"
Length: 4-15/16"
Weight: 9 oz
Shackle pin diameter: 3/16"
Maximum line diameter: 3/8"
Maximum working load: 600 lb.
Breaking load: 1500 lb.
    HARKEN 57MM RATCHET BLOCK- SWIVEL, BECKET, CAM CLEAT
    Harken
    $202.20
    H-18 Surefoot EVA Deck Grip Kit - Peel and Stick

The Hobie 18 Surefoot EVA Deck Grip Kit features 3m peel and stick backing on cut-diamond-textured EVA foam. Ideal rail and or deck grip on all dinghies and catamarans. EVA traction pads offer grip, padding and a long life span.  EVA is a lightweight foam doesn't absorb water the way carpet does, so there is minimal weight when it gets wet and it dries quickly!

Hobie 18 kit includes four 3" x 40" strips and four 3" x 20" strips - covers the side rails
    Black Grey
    H-18 SUREFOOT EVA KIT
    Murrays Sports
    $79.00
    Out of Stock
    Back Up Casting H18 Bow Tang
Murrays Part# 50-61120001
Hobie® factory replacement back up casting for Hobie® 18 bow tang.
    BACK UP CASTING H-18 BOW TANG
    Hobie
    $50.99
    Out of Stock
    H18 Shroud Anchor Plate Kit

Murrays Part# 50-64100001

The Shroud Anchor Plate Kit H18 is the Hobie® factory replacement shroud anchor plate kit for Hobie 18.

Applications:

This kit is also used to re-enforce the crossbar bolts on Hobie 18s with wings or the lighter H18 boats that were built from 1984-1988.
    H-18 SHROUD ANCHOR PLATE KIT
    Hobie
    $49.99
    BK WH
    6" ARMSTRONG DECK PLATE
    Armstrong
    $49.00
    Hobie Shroud Anchor Pin Hobie 16, 17 and 18. 20100000 20100010
    H-16/17/18 SHROUD ANCHOR PIN UPDATE
    Murrays Sports
    $39.99
    H14/16/17/18 Gudgeon Lower

Murrays Part# 25-3352

The latest, strongest rudder gudgeon design with welded sleeve bushings provides large, smooth bearing surfaces between rudder pins and gudgeons. Replace flared gudgeons with their sharp edges and point loading that can cause early rudder pin failure. For Hobie® 14, 16 and 17, order separate upper and lower gudgeons. For all other Hobie® cats with new-style castings, post 1986, order 4 for a complete set .

Replacement for Hobie Part# 50101401
    H14/16/17/18 LOWER GUDGEON
    Murrays Sports
    $35.99
    Nylon Port Fastener Kit



The Port Nylon Fastener Kit includes all the necessary nylon fasteners (screws, washers and nuts) plus marine silicone sealant for the installation of two access ports, also known as hatches, on to a catamaran like a Hobie, Nacra or Prindle.

Use this page to order:
001-1159 White
001-1160 Black
    White Black
    NYLON PORT FASTENER KIT
    Murrays Sports
    $29.00
    6" Access Port with Lip

Murrays Part# 001-4210WH

The 6" Access Port with Lip is standard on the Hobie 18 and newer Prindle cats and it is an excellent upgrade for older Prindles. Ports can be installed on any flat deck, including kayaks, where there is 8-1/2" of flat surface available. These ports come with the inner lip so they are compatible with the 6"cat bag. Does not include hardware, hardware options shown in the related items section below.

White port is Murrays #01-4210WH. Compare to Hobie Cat® #
    6" ACCESS PORT WITH LIP
    Sailing
    $22.00
    H18 Thru-Deck Fairlead

Murrays Part# 50-60270000

Fairlead Thru-Deck H18 for trapeze shock cord for skipper and crew trapeze lines that go through the lip on the outside of the hull.

Center hole on this fairlead is 7/8" diameter and is sleeved with a stainless steel ferrule. Mounting screw holes have a center-to-center measurement of 1-3/8". Hobie® factory replacement part.

Hobie Part# 60270000
    H-18 THRU-DECK FAIRLEAD
    Hobie
    $19.99
    Out of Stock
    H18 Bow Tang

Murrays Part# 50-60120000

Hobie Cat® factory replacement bow tang for Hobie® 18.
    H-18 BOW TANG
    Hobie
    $13.99
    Ronstan Series 19 C-Track End Cap

Murrays Part# 21-0366

These are End Stops for the new C-Track by Ronstan. Similar to the stainless tracks used on H18 and H16 in the past. Track end, plastic

Best replacement for End stop for 5/8" jib track as on Hobie® 16 or Hobie® 18. The end stop can be fastened with #19-1620 screw or #19-5021 6-4 countersunk rivet. Compare to Hobie Cat part #20260000.
    RONSTAN JIB TRACK END CAP
    Ronstan
    $9.99
    Made from 18 stainless steel these set screws are chemical resistant and may be mildly magnetic. They have a thin edge that digs into the contact surface for a secure hold. Length listed is the overall length. Screw for the Hobie 18 wing mount kit. 65071001
    SOCKET SCREW 5/16-18 x 2"
    Misc
    $5.00
    Drain Plug with Plastic Base

Murrays Part# 001-0051

This lightweight and inexpensive drain plug features a molded recess in the molded nylon base that traps sealant (sold separately) in place, providing a more watertight seal. Gasket included.
    DRAIN PLUG WITH PLASTIC BASE
    Sea Dog
    $5.00
    Universal Drain Plug for most Hobie, Nacra and Prindle Catamarans which includes a gasket and fits most Hobie, Nacra and Prindle catamarans. Hobie part number 10091000
    Hobie drain plug 10091000 Hobie 18
    DRAIN PLUG WITH GASKET
    Misc
    $4.05
    O-Ring: 6" Screw-In Port

Murrays Part# 001-4210OR



​Replacement “O” ring for 6″ port (hatch) #01-4210. Viking, Sea Dog
    O-RING: 6" SCREW-IN PORT
    Sea Dog
    $2.00
    Harken 22mm Spring

Murrays Part# 28-0071

Harken universal stand-up spring supports blocks on pad eyes, eyestraps, bases and traveler cars. Weight: .32 oz.
This works well with snap shackle w/tack to upgrade a typical beachcat mainsheet system.
    HARKEN 22MM SPRING
    Harken
    $1.55
    Screw RHMS #12-24 X 1.25 Stainless Steel
Murrays Part# 19-3520
Stainless steel, round head #12-24 x 1.25" machine screw is a replacement screw for Hobie® rudder gudgeon.
    SCREW RHMS #12-24 X 1.25 (SS)
    Misc
    $1.10
    Daggerboard Carpet

Murrays Part# 56-1082

​Approximately 1-1/2″ wide carpet installs in daggerboard wells.

Nacra factory item #1083.


Sold by the foot.
    DAGGERBOARD CARPET
    Murrays Sports
    $1.00
    Rivet CCP 6-10 (3/16 X 5/8)
Murrays Part# 19-5034
Stainless steel 3/16" x 5/8" rounded pan head rivet. Compare to Hobie Cat® #8010121.
Halyard mast cleat rivet
    RIVET CCP 6-10 (3/16 X 5/8)
    Misc
    $0.85
    Screw THMS 1/4-20 X 1-5/8"

Murrays Part# 50-8030601

Hobie® factory replacement 1/4-20 x 1-5/8" screw.

Hobie Part# 8030601
    SCREW THMS 1/4-20 X 1-5/8"
    Hobie
    $0.79
    Screw RHMS 1/4-20 X 1"

Murrays Part# 50-8030211

Hobie® factory replacement round head machine screw measures 1/4-20 x 1". Measurements are diameter and threads per inch times grip length.

Applications:
Hobie 18 - Shroud anchor plate screw
    SCREW RHMS 1/4-20 X 1"
    Hobie
    $0.79
    Nut Nylock 5/16-18 Stainless Steel
Murrays Part# 19-2520
5/16-18 nylock nut is used on Hobie® rudders. The stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Compare to Hobie Cat® item #8050311 and 8050321 shroud anchor pin nut
Used with Hobie Getaway Bow Tang Bolt
    NUT NYLOCK 5/16-18 (SS)
    Misc
    $0.75
    Hobie Drain Plug Screw

Murrays Part# 50-8031731




This screw is used to hold the rudder housing in the back of many of the Hobie Beach cats. H14, H16, H17, H18

Hobie Part# 8031731
    HOBIE DRAIN PLUG SCREW
    Hobie
    $0.49
    Used for tiller connection on Hobie Cats®. The stainless 1/4-20 stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Equivalent to Hobie #8050111. Also Equivalent to Nacra/Prindle F123 gudgon nut for all Prindle and older Nacras.
Applications:
Hobie 18 / H18:
Bow Tang Nut Qty: 6
Rudder Adjustment: 1
Hobie Getaway: Forestay Yoke Nut
    NYLOCK NUT 1/4-20 SS
    Misc
    $0.45
    WASHER #8 (WH NYLON)

Murrays PN 19-4006WH

White nylon washer is used for installation of access ports (hatches).
    WASHER #8 WHITE NYLON
    Misc
    $0.35
    FHSMS #8 X 1 Stainless Steel

Murrays Part# 19-1620
Flat head, self-tapping, stainless steel #8 x 1" sheet metal screw.
This screw is commonly used to hold the track endcaps on pre 1997 H16 Jib Traveler Tracks and all H18 Jib Traveler Tracks.
Can screw into aluminum or fiberglass.
    SCREW FHSMS #8 X 1" (SS)
    Misc
    $0.34
    Screw FHSMS #8 X 3/4 Stainless Steel
Murrays Part# 19-1621
Flat head, self tapping, stainless steel sheet metal screw #8 x 3/4"
Compare to Hobie Part 8031501
Used to mount swivel jam cleat and Jib Car Stop
    SCREW FHSMS #8 X 3/4" (SS)
    Misc
    $0.34
    Cotter Pin 3/32 X 3/4
Murrays Part# 19-1015
Cotter pins are used on all Hobie, Nacra and Prindle rudder pins. They are used to secure the rudder pins. Compare to Hobie Cat® #8060111.
Stainless steel cotter pin measures 3/32" x 3/4".
    COTTER PIN 3/32 X 3/4" SS
    Misc
    $0.18