Hobie 18 Front Crossbar Parts

30 products

    Parts for your Hobie 18 Front Crossbar

    30 products
    Out of Stock
    Crossbar Casting Front Right H18-Black Murrays Part# 50-60160011 Hobie® factory replacement right front crossbar casting for Hobie® 18 Hobie Part# 60160011
    CROSSBAR CASTING FRONT RT H18-BLACK
    Hobie
    DOLPHIN STRIKER ROD H18
    Hobie
    Hobie 18 Mast Base Hinge casting 60650011
    H-18 Mast Base Hinge
    Murrays Sports
    Harken Swivel with Carbo Cam Bullseye Murrays Part# 25-3010 Swivel cam cleats are ideal for main traveler control and up-release jib cleating systems. Cam cleats and fairleads should be selected on the basis of need. Order plastic base pads and flat head screws separately to mount to your front crossbar.
    HARKEN SWIVEL W/CARBO CAM & BULLSEYE
    Harken
    DOLPHIN STRIKER POST H18 (NEW)
    Hobie
    Out of Stock
    FRONT INBOARD SUPPORT CAST KIT
    Hobie
    V JAM CLEAT BOOM (3/16" HOLES)
    Hobie
    SWIVEL MOUNT BASE W/FASTENERS
    Hobie
    Murrays Part# 001-4045 Mast Bearing Kit enables smooth mast rotation on the Hobie® 18. The kit includes a new mast bearing, stainless steel washers and Teflon washer. To mount, use one #19-3019 screw (included) for post-1990 Hobie 18 or one #19-3020 screw (sold separately) for pre-1990 Hobie 18.  Compare to Hobie Cat® #1132 (bearing and Teflon™ washer).
    MAST BEARING KIT: H-18
    Murrays Sports
    HOBIE 18 CHANNEL RETAINING PLATE HOBIE PART NUMBER 61110000
    CHANNEL RETAINING PLATE H18
    Murrays Sports
    Out of Stock
    Bolt Socket Head 3/8-16 X 3.75" Murrays Part# 50-8040561 Hobie® factory replacement 3/8-16 x 3.75" socket head bolt. Applications: Hobie 18 inboard front crossbar
    BOLT SOC HEAD 3/8-16 X 3.75"
    Misc
    MAST BEARING H18
    Hobie
    3-HOLE PAD KIT: HOBIE AND PRINDLE
    Murrays Sports
    Out of Stock
    Dolphin Striker Post Sleeve Murrays Part# 50-61140000 Hobie® factory replacement dolphin striker post sleeve for Hobie 18 Hobie Part# 61140000
    DOLPHIN STRIKER POST SLEEVE
    Hobie
    MAST HEAD/BASE SHEAVE H18
    Hobie
    Ronstan Series 19 C-Track End Cap Murrays Part# 21-0366 These are End Stops for the new C-Track by Ronstan. Similar to the stainless tracks used on H18 and H16 in the past. Track end, plastic Best replacement for End stop for 5/8" jib track as on Hobie® 16 or Hobie® 18. The end stop can be fastened with #19-1620 screw or #19-5021 6-4 countersunk rivet. Compare to Hobie Cat part #20260000.
    RONSTAN SERIES 19 C-TRACK END CAP
    Ronstan
    Sealed Rivet CCP 6-8 (3/16 X 1/2) Murrays Part# 19-5033S Sealed rivets have a sealed end that does not require rivet casings to make them water tight. One and done, no casing needed, just insert and pop as you would a normal rivet, and your hole will be sealed. Sealed Stainless steel 3/16" x 1/2" rounded pan head rivet. Compare to Hobie Cat® #8011231 Rivet and Hobie Cat® #8011291 rivet casing.
    RIVET CCP SEALED 6-8 (3/16 X 1/2)
    Misc
    BOLT 3/8-16 X 2"
    Misc
    Rivet CCP 6-8 (3/16 X 1/2) Murrays Part# 19-5033 Stainless steel 3/16" x 1/2" rounded pan head rivet. Compare to Hobie Cat® #8011231.
    RIVET CCP 6-8 (3/16 X 1/2)
    Misc
    NUT NYLOCK 3/8-16 (SS)
    Misc
    SCREW RHMS 1/4-20 X 1"
    Misc
    NUT NYLOCK 3/8-24 lock nut
    Misc
    Nut Nylock 5/16-18 Stainless Steel Murrays Part# 19-2520 5/16-18 nylock nut is used on Hobie® rudders. The stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Compare to Hobie Cat® item #8050311 and 8050321 shroud anchor pin nut Used with Hobie Getaway Bow Tang Bolt
    NUT NYLOCK 5/16-18 (SS)
    Misc
    SCREW 10-24 X 1.5" (NYLON)
    Misc
    Used for tiller connection on Hobie Cats®. The stainless 1/4-20 stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Equivalent to Hobie #8050111. Also Equivalent to Nacra/Prindle F123 gudgon nut for all Prindle and older Nacras. Applications: Hobie 18 / H18: Bow Tang Nut Qty: 6 Rudder Adjustment: 1 Hobie Getaway: Forestay Yoke Nut
    NYLOCK NUT 1/4-20
    Misc
    Hobie 8080581 Hobie factory replacement 3/8" lock washer is used on Hobie 18 front and rear inboard support castings.
    3/8 LOCK WASHER
    Misc
    Screw PHMS #10-32 X 1 Stainless Steel Slot Head Murrays Part# 19-2915 Stainless steel, pan head #10-32 x 1" machine screw with slot is used as dolphin striker screw on all Prindles. Replaces Murrays item #56-F112. Also used in some Hobie Applications, compare to 8030111 Hobie Part. Applications: H18/18 SX/16 and Getaway Tiller Hinge Screw: 2
    SCREW PHMS #10-32 X 1 (SS) SLOT HEAD
    Misc
    FHSMS #8 X 1 Stainless Steel Murrays Part# 19-1620 Flat head, self-tapping, stainless steel #8 x 1" sheet metal screw. This screw is commonly used to hold the track endcaps on pre 1997 H16 Jib Traveler Tracks and all H18 Jib Traveler Tracks. Can screw into aluminum or fiberglass.
    FHSMS #8 X 1 (SS)
    MISC
    Screw FHSMS #8 X 3/4 Stainless Steel Murrays Part# 19-1621 Flat head, self tapping, stainless steel sheet metal screw #8 x 3/4" Compare to Hobie Part 8031501 Used to mount swivel jam cleat and Jib Car Stop
    FHSMS #8 X 3/4 (SS)
    Misc
    WASHER FLAT 1/4 X 5/8"
    Hobie