Hobie 17 Rudder and Centerboard Parts

62 products

Parts for your Hobie 17 Rudder & Steering system and Centerboards

62 products

Sort

HOBIE EPO3 RUDDER BLADE

H17/18/20 Upper Right Rudder Casting

Murrays Part# 50-50341001

Hobie® factory replacement upper right rudder casting for Hobie® 17, 18 or 20. Use four 6-8 rivets (#19-5033) for installation.
Hobie Part# 50341001

H-17/18/20 UPPER RIGHT RUDDER CASTING

H17/18/20 Lower Rudder Casting

Murrays Part# 50-50322001

Hobie® factory replacement lower rudder casting for Hobie® 17, 18, 20, Getaway and Wave. This casting does not fit Hobie® 14 or 16.

H-17/18/20 LOWER RUDDER CASTING

H17/18/20 Upper Rudder Casting
Murrays Part# 50-50321001

Hobie® factory replacement upper left rudder casting for Hobie® 17, 18, 20 or Wave. Use four 6-8 rivets (#19-5033) for installation.

H-17/18/20 UPPER RUDDER CASTING

H16/17/18 Tiller Crossbar-Post-1995

Murrays Part# 50-20521001

The Tiller Crossbar H16, H17, H18 Post-1995- is a Hobie® factory replacement tiller crossbar for 1995 and newer Hobie® 16, 17 or 18.

The Post 95 version comes with the new style quick connect tiller connection system.

H-16/17/18 TILLER CROSSBAR-POST 1995

Hobie 1953 tiller connection kit - new style

HOBIE TILLER CONNECTOR KIT

Hobie Rudder Blade - White Nylon

Murrays Part# 50-20493000

The Hobie Rudder Blade - White Nylon is a solid molded white nylon rudder blade for use on virtually all Hobie Catamarans. Hobie factory nylon rudder blades are stock on Hobie 14, 16, 17, 18, 20 and Waves with pre-EZ Loc rudder systems. Hobie rudders are sold undrilled and we recommend that you use your old rudder as a template to drill your new rudder.

Hobie Part# 20493000

HOBIE RUDDER BLADE - WHITE NYLON

Fiberglass Tiller H14/16
Murrays Part# 50-20550001
84" Hobie Fiberglass Tiller Extension
The 84" Hobie Fiberglass Tiller Extension is the Hobie factory 84" fiberglass tiller extension with hinge for the Hobie 14 or 16. This stick can be cut to 60" for Getaway or Wave.

H-14/16 FIBERGLASS TILLER

Rudder Blade EZ Lock With Indents

Murrays Part# 50-20491000

Hobie is no longer producing two different nylon rudder blades. Use this part to replace your plastic rudder blades for Hobie 14, 16, 17 and 18 beach cats. This is the standard part that comes on Hobie Wave and Hobie Getaway boats with EZ Loc rudder systems

RUDDER BLADE EZ LOCK WITH INDENTS

Tiller Crossbar Adjustable Cap Kit

Murrays Part# 50-6040000M

Murrays Tiller Crossbar connection kit is a complete kit to connect the Hobie tiller cross bar and tiller arms. This is modeled after the original design but with some upgrades. We use 2 adjustable end caps to extend the overall adjustment length. Allows users shorten their tiller crossbar due to corrosion. 2 adjustable caps also allows users to adjust the crossbar length from either end of the bar. The tiller crossbar

TILLER CROSSBAR ADJUSTABLE CAP KIT

84" Murrays Fiberglass Tiller Extension

Murrays Part# 001-1320

The 84" Murrays Fiberglass Tiller Extension is a lighter version of the Hobie fiberglass tiller extension. It was developed by an A Fleet Racer looking for a lighter more economic alternative. Murrays helped get them into production and here they are!

Features:

5/8" diameter black fiberglass tube

Hobie yoke base, same as the Hobie version

16" grip on the top

84" fixed length

Weight: 3/4 lb.

MURRAYS 84" FIBERGLASS TILLER EXTENSION

Hobie Rudder Covers

Murrays PN 50-82420000

Rudder covers by Hobie protect your rudders from nicks and grime. Hobie's rudder covers feature straps with Fastex® fasteners to keep the covers firmly in place, even when trailering. The covers fit all Hobies except H21SE (Special Edition).

These come as a pair.

Hobie part number 82420000

HOBIE RUDDER COVER

Centerboard Spring H17
Murrays Part# 50-50350140
Hobie® factory replacement centerboard spring for Hobie 17
Hobie Part# 50350140

H-17 CENTERBOARD SPRING

H17/18/20/21/Wave and Getaway
Rudder Cam Kit

Murrays Part# 001-3550

The Rudder Cam Kit: H17, H18, H20, H21, Wave, & Getaway are replacement rudder cams which help keep your Hobie’s rudder lock-down mechanism functioning properly. This kit includes sister screws to install the cams, making it easier to replace the cams. Purchase the complete kit if your boat has the stock flare pins; or you can purchase just the cams (#50-10480000 each) if your boat already has sister screws.

H-17/18/20/21/WAVE AND GETAWAY RUDDER CAM KIT

Quick Release Pin 1/4 X 1-1/4 with Lanyard

Murrays Part# 18-4M125L

QUICK RELEASE PIN 1/4 X 1-1/4" WITH LANYARD

H14/16/18/20/Wave Rudder Cam Stop Plate

Murrays Part# 50-20352000

Hobie factory replacement rudder cam plate for Hobie 14, 16, 17, 18 (1987 and later) and Wave (with aluminum castings).

Hobie Part# 20352000

H-14/16/18/20/WAVE RUDDER CAM STOP PLATE

Tiller Crossbar Adjustable Cap Kit

Murrays Part# 50-60400011M

Murrays Tiller Crossbar Adjustable Cap Kit installs in the end of the Hobie tiller crossbar and allows you to adjust the width of the crossbar which controls the angel of the rudders.

Hobie discontinued this part and this is a Murrays Replacement part that we have made here in California.

Applications: H14, H16, H17, H18, Hobie 18 SX tiller x-bar

Tiller Crossbar Adjuster: 1

HOBIE TILLER CROSSBAR ADJUSTABLE END CAP

H17 Tiller Arm-Black
Murrays Part# 50-50321111

Hobie® factory replacement black tiller arm tube for Hobie® 17.

H-17 TILLER ARM-BLACK

Rudder Locking Kit Hobie 17, 18, 20, 21

Murrays Part# 001-3552

The Rudder Locking Kit Hobie 17, 18, 20, 21 includes the rudder spring, rudder casting screw, and the rudder plunger for the Hobie 17, 18, 20 and 21.

Delrin screw is 3/4-10 thread. In many cases you can drill it out with a 5/8" drill bit and then get a 3/4-10 tap to clear the threads.

H-17/18/20 and 21 RUDDER LOCKING KIT

Rudder Pins H17/18 Stainless Steel

Murrays Part# 001-4273

Weight-saving compared to solid stainless steel pins, hollow stainless rudder pins with still beefy .065″ wall provide reduced wear and the good long-term durability. The universal stainless steel 3/8″ x 9-1/4″ rudder pins are suited for; Hobie 17/18/20 rudder castings. Also used on older Hobie Wave and Getaways with metal rudder castings.

Cotter pins are included.
Alternative to Hobie Cat® #60880011.  (* Pre EZ LOC Rudder c

H-17/18 RUDDER PINS PR (SS)

H14/16/17/18 Gudgeon Lower

Murrays Part# 25-3352

The latest, strongest rudder gudgeon design with welded sleeve bushings provides large, smooth bearing surfaces between rudder pins and gudgeons. Replace flared gudgeons with their sharp edges and point loading that can cause early rudder pin failure. For Hobie® 14, 16 and 17, order separate upper and lower gudgeons. For all other Hobie® cats with new-style castings, post 1986, order 4 for a complete set .

Replacement for Hobie Part# 50101401

H-14/16/17/18 LOWER GUDGEON

Rudder Pins H17, H18, Wave, Getaway (Aluminum)
Murrays Part# 001-4274
Aluminum rudder pins for the Hobie 17, 18, Wave and Getaway.  Aluminum 3/8″ x 9-1/4″ rudder pins, cotter pins are included. 

Sold in pairs

Compare to Hobie Cat® #60880001

H-17/18/WAVE AND GETAWAY ALUMINUM RUDDER PINS

Rudder Cam Screws H17, H18, H20,
Older Wave and Getaway
Murrays Part# 001-3551
The Murrays Rudder Cam Pins are a pair of sister screws for use on the Hobie 17, 18, 20, 21, as well as the older Hobie Wave and Getaway rudder cams. These pins are an upgrade form the original stock hollow flare rivet that came on the Hobie. The Sister Screws are much easier to install and remove, and they are reusable.
Compare to Hobie Cat® #5203 and #50312301.
Sold in pairs

H-17/18/20/OLDER WAVE AND GETAWAY RUDDER CAM PINS

Tiller Connection Kit
Murrays Part# 001-2061
The Murrays Tiller Connection Kit assures consistent rudder alignment through the full rudder sweep. Spring-loaded half balls and contoured spacers take the slop out of the tiller-to-crossbar connection on Hobie Cats. Racing class legal. Each kit contains 2 connectors to join the tiller crossbar to the tiller arms. Compare to Hobie Cat® #3052.
Applications:; Hobie 14, 16, 17, 18, 18SX

Hobie, Nacra, Prindle Tiller Connection Kit

Murrays Part# 001-2061

The Murrays Tiller Connection Kit assures consistent rudder alignment through the full rudder sweep. Spring-loaded half balls and contoured spacers take the slop out of the tiller-to-crossbar connection on Hobie Cats. Racing class legal. Each kit contains 2 connectors to join the tiller crossbar to the tiller arms.

Applications:  Hobie 14, 16, 17, 18, 18SX

Sold in pairs

Compare to Hobie Cat® Part#

TILLER CONNECTION KIT (PR)

H14/16 Upper Gudgeon

Murrays Part# 25-3351

This latest, strongest design with welded sleeve bushings provides large, smooth bearing surfaces between rudder pins and gudgeons. Replace flared gudgeons with their sharp edges and point loading that can cause early rudder pin failure. For Hobie® 14's, 16's and 17, order separate upper and lower gudgeons.

 For all other Hobie® cats Part# 25-3352 for both gudgeons. Each

This gudgeon is a replacement for item #50101301

H-14/16 UPPER GUDGEON

Hobie Tiller End Cap

Murrays Part# 50-10400010

Tiller arm end cap for Hobie Cats is a factory replacement part. Use two 6-6 rivets (item #19-5032) for installation.

HOBIE TILLER END CAP

Centerboard Pivot Pin H17
Murrays Part# 50-50104001
Hobie® factory replacement centerboard pivot pin for Hobie® 17
Hobie Part# 50104001

H-17 CENTERBOARD PIVOT PIN

Rudder Pins H17/18 (Nylon)

Murrays Part# 001-4271

Nylatron rudder pins are sacrificial for use in the surf (they'll break before your rudder system does) and should be inspected often for wear. These universal 3/8" x 9-1/4" nylon rudder pins are suited for all Hobie® 17/18/Wave rudder castings. Compare to Hobie Cat® #5052 fiberglass rudder pins (pair).

RUDDER PINS H-17/18 PR (NYLON)

Hobie Rudder Cam
Hobie part number 10480000
Hobie factory replacement cam. Rudder cams should be inspected and replaced periodically. Always replace cams that are bent out of shape.

Used on all Hobie Catamarans with metal housing rudder systems. Compatible on all Hobie 14, 16, 17, 18, 20, 21SC and 21SE as well as older Wave and Getaway models.

Not compatible with the Hobie Wave and Getaway EZ Loc plastic rudder housing rudder system.

HOBIE RUDDER CAM

Soft Grip Standard Extension .570 x 11"

Murrays Part# 007-3206

This is a grip upgrade for the standard Hobie Tiller extension, it will also fit the Murrays fixed tiller extension as well.

Hobie Part# 3206

SOFT GRIP STANDARD EXTENSION .570 x 11"

Hobie Tiller Extension Hinge

Murrays Part# 50-10532010

Hobie® factory replacement tiller extension hinge for #50-20550001 Hobie® Fiberglass tiller extension. Also used on Nacra tillers.

Hobie Part Number: 10532010

HOBIE TILLER EXTENSION HINGE

H18 Rudder Cam Pin

Murrays Part# 50-50312301

Hobie® factory replacement rudder cam pin for Hobie 17, 18, 20, 21SC and 21SE as well as older Wave and Getaway models.

H-18 RUDDER CAM PIN

Murrays Part# 001-0062
Replacement tiller yoke assembly for all hiking sticks sold by Murrays. Used to connect the tiller extension to the tiller crossbar. Includes two contoured spacers that provide a solid platform for the yoke to sit on. Compare to Hobie Cat® Tiller yoke assembly #3205 or NACRA connection part tiller/joystick #31072
Applications: All Hobies and Prindles
Tiller Yoke Assembly: 1

TILLER YOKE ASSEMBLY WITH SPACERS

Murrays Part# 50-10432000
Hobie® factory 2½" spring for Hobie® 16 lower rudder casting. This spring is longer and stiffer than original equipment (#50-10430000), providing additional tension if you are having trouble with rudder kick up.
Used on Hobie 18 Rudder Systems from late 80s through now.
Used on Hobie 16 Rudder Systems after 1983
Used on Hobie Getaway Rudder Systems pre- EZ Loc
Hobie part number 10432000

HOBIE RUDDER SPRING-LONG

Kisme Kleet (4)

Murrays Part# 005-1010

KISME KLEET (4)

Hobie 18 rudder plunger. Hobie Part number 50312201. Also use on the 17 as well as the older Wave and Getaway

H-17/18/GETAWAY RUDDER CAST PLUNGER

Rudder Casting Lock Spring
Murray Part# 50-10430000
Hobie factory replacement 2-1/8" lock spring for rudder casting. Replace rudder springs with this original spring supplied on Hobie® 14, 16, (pre 1983) 17 and 18.
Compare to HC part number 10430000
H14, H16, H17, H18, H20

HOBIE RUDDER SPRING

RUDDER CASTING DELRIN SCREW - rudder locking adjustment screw - 60450000

HOBIE DELRIN RUDDER SCREW

Centerboard Handle H17
Murrays Part# 50-50702001
No longer available - Discontinued by Hobie
Hobie Part# 50702001

H-17 CENTERBOARD HANDLE

Rudder Stiffening Kit

Murrays Part# 001-2053

The Rudder Stiffening Kit for all Hobies eliminates excessive clearances between rudders and castings which cause wobble and thwart rudder alignment. Kit has 4 stainless nylock nuts and 8 spacers. Compare to Hobie Cat® item #136.

RUDDER STIFFENING KIT

1 2 Next

Recently viewed

Hobie 17 Rudder and Centerboard Parts