Hobie 17 Parts

Hobie 17 Parts

227 products

    Parts for your Hobie 17

    227 products
    Gooseneck Boom Pin Murrays Part# 50-50502201 Hobie Cat gooseneck boom pin for securing boom assembly to mast at the gooseneck joint. Hobie Part# 50502201
    HOBIE GOOSENECK BOOM PIN
    Hobie
    Nut Jam 9/16-18 Low Profile Murrays Part# 50-8050461 Hobie® factory replacement low-profile 9/16-18 jam nut is used on Hobie 17 dolphin striker. Hobie Part# 8050461
    NUT JAM 9/16-18" LOW PROFILE
    Hobie
    Out of Stock
    Bolt 5/16-18 X 2" Murrays Part# 50-8040331 Replacement 5/16-18 x 2" bolt is used as a rudder bolt on Hobie® Pre-EZ Lock Rudder System. Hobie Part# 8040331
    BOLT 5/16-18 X 2"
    Misc
    H17 Illustrated Parts List Murrays Part# 50-87173000 Hobie® factory publication aids in identifying parts for the Hobie 17 and 17 Sport. Find the item number for the part you need and easily search the Murrays store. The parts list is also available for free download at the Hobie Cat® Web site.
    H-17 ILLUSTRATED PARTS LIST
    Murrays Sports
    Daggerboard Carpet Murrays Part# 56-1082 ​Approximately 1-1/2″ wide carpet installs in daggerboard wells. Nacra factory item #1083. Sold by the foot.
    DAGGERBOARD CARPET
    Murrays Sports
    Hobie rivet casings sleeves seal rivets to prevent water penetration. When used with a rivet they seal the hole to prevent water from getting through the center of the rivet. Rivet Casings are recommended for use on all rivets on the mast to keep the mast water tight. Compatible with all 3/16 diameter rivets up to 5/8" long. Compatible with all rivets on Hobie, Nacra and Prindle catamarans except traveler tracks. Requires 13/64" hole. Hobie part number 8011291, 8011290, also called rivet cap.
    RIVET CASING 6-10(3/16 X 5/8)
    Hobie
    Screw 1/4-20 x 1" THMS-P SS Murrays Part# 50-8030701 Hobie® factory replacement 1/4-20 x 1" stainless steel screw. Used on Hobie® pre-EZ-Loc rudder system, tendon tiller connector, rudder adjuster, Hobie 20 shroud anchor plate. Applications: H18/ Hobie 18 SX Rudder Adjuster Screw: 1 Compare to Hobie Part# 8030701
    SCREW STAINLESS STEEL 1/4-20x1"
    Hobie
    Rivet CCP 6-10 (3/16 X 5/8) Murrays Part# 19-5034 Stainless steel 3/16" x 5/8" rounded pan head rivet. Compare to Hobie Cat® #8010121. Halyard mast cleat rivet
    RIVET CCP 6-10 (3/16 X 5/8)
    Misc
    Rivet CCP 6-8 (3/16 X 1/2) Murrays Part# 19-5033 Stainless steel 3/16" x 1/2" rounded pan head rivet. Compare to Hobie Cat® #8011231.
    RIVET CCP 6-8 (3/16 X 1/2)
    Misc
    Out of Stock
    Nut Nylock 3/8-24 Murrays Part# 50-8050511 Replacement 3/8-24 nylock nut is used on Hobie® 14, 16 and 18 dolphin striker rods, as well as Hobie® 17 inboard support. Hobie Part# 8050511
    NUT NYLOCK 3/8-24"
    Hobie
    3/16 - 1/4" Split Ring with Pigtail Murrays Part# 22-9491 A pigtail makes this split ring (ring ding) easier to open than standard split rings. For use on 3/16″ – 1/4″ clevis pins Material: 316 Stainless steel. Medium Split ring Dimensions: 5/8″ Diameter This is the most common size Split ring on Hobie, Nacra and Prindle Catamarans. Applications: All Hobies Shroud and Forestay split ring H18/ Hobie 18 SX – Tiller Yoke Clevis Pin Ring Also called Ring Ding, Clevis Ring, Cotter Ring or Ringy Ding
    3/16 - 1/4" SPLIT RING WITH PIGTAIL
    Misc
    RIVET CCP 6-6 (3/16 X 3/8) Murrays Part# 19-5032 Stainless steel 3/16" x 3/8" pan head rivet Among other uses, the Stainless steel 3/16" x 3/8" pan head rivet can be used when Hobie® rivet #8010131 is specified: Hobie 14 (2) or 16 (4) mast head Hobie Wave/Getaway/14/16/17/18/18SX/ mast base (4) Hobie 14/16 rudder upper casting (2) Hobie 14/16 tiller end cap (2) Hobie 14/16 boom front end cap (3) Pair with stainless steal rivet casings to seal the holes when using on the mast.
    RIVET CCP 6-6 (3/16 X 3/8)
    Misc
    Murrays PN 001-0053 The Murrays Rudder Stiffening Spacer is a 2" diameter spacer for use on Hobie, Nacra and Prindle catamarans to eliminate excessive clearances between rudders and castings which cause rudder slop, side to side wobble, and thwart rudder alignment. A kit with spacers and nuts is also available (#01-2053).  The Murrays Rudder Stiffening Spacer are quite thin so that you can achieve a perfect fit. Standard kits come with 8 spacers.
    RUDDER STIFFENING SPACER
    Murrays Sports
    3/16 - 1/4" Split Ring Murrays Part# 22-9492 Stainless steel split ring (ring ding) for 3/16″-1/4″ diameter clevis pin. This is the standard size Hobie split ring used all over the boats, most commonly on the shrouds, forestay and roller furler Medium Split ring Dimensions: 5/8″ Diameter Material: 316 Stainless steel. This is the most common size Split ring on Hobie, Nacra and Prindle Catamarans. 20860000 Medium Clevis Ring.
    3/16-1/4" SPLIT RING
    Misc
    Nut Nylock 5/16-18 Stainless Steel Murrays Part# 19-2520 5/16-18 nylock nut is used on Hobie® rudders. The stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Compare to Hobie Cat® item #8050311 and 8050321 shroud anchor pin nut Used with Hobie Getaway Bow Tang Bolt
    NUT NYLOCK 5/16-18 (SS)
    Misc
    1/2 BALL (NYLON) - Hobie half round washer spacer tiller connector - Hobie part number 11510000 HOBIE HALF SPHERE TILLER CONNECTOR
    NYLON 1/2" BALL
    Murrays Sports
    Hobie Drain Plug Screw Murrays Part# 50-8031731 This screw is used to hold the rudder housing in the back of many of the Hobie Beach cats. H14, H16, H17, H18 Hobie Part# 8031731
    HOBIE DRAIN PLUG SCREW
    Hobie
    Nut Nylock Lo-Pro 1/4-20 Murrays Part# 50-8050101 Hobie® factory replacement low profile 1/4-20 nylock nut. Used on Hobie 14 and 16 gooseneck assembly. Hobie Part# 8050101
    NUT NYLOCK LOW PROFILE 1/4-20"
    Hobie
    FIBER TENDON SCREW
    Misc
    Used for tiller connection on Hobie Cats®. The stainless 1/4-20 stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Equivalent to Hobie #8050111. Also Equivalent to Nacra/Prindle F123 gudgon nut for all Prindle and older Nacras. Applications: Hobie 18 / H18: Bow Tang Nut Qty: 6 Rudder Adjustment: 1 Hobie Getaway: Forestay Yoke Nut
    NYLOCK NUT 1/4-20 SS
    Misc
    Nut Nylock #10-32 Stainless Steel Thick Murrays Part# 19-2515 Mainsheet block replacement nut. The stainless hex nut with nylock insert will not rust or work loose if properly installed. Fits Hobie Main Traveler Car. Fits Hobie Tiller Hinge Screw. Fits Hobie Masthead Sheave Screw H16 Hobie Getaway Compare to Hobie Part Number 8050201
    NUT NYLOCK #10-32 (SS) THICK
    Misc
    Screw PHMS #10-32 X 1 Stainless Steel Slot Head Murrays Part# 19-2915 Stainless steel, pan head #10-32 x 1" machine screw with slot is used as dolphin striker screw on all Prindles. Replaces Murrays item #56-F112. Also used in some Hobie Applications, compare to 8030111 Hobie Part. Applications: H18/18 SX/16 and Getaway Tiller Hinge Screw: 2
    SCREW PHMS #10-32 X 1" (SS)
    Misc
    WASHER #8 (WH NYLON) Murrays PN 19-4006WH White nylon washer is used for installation of access ports (hatches).
    WASHER #8 WHITE NYLON
    Misc
    Comptip Cap Plug Murrays Part# 50-8090900 This part is used to seal the hole in the Comptip of a Hobie cat after the expanding foam has been put in. Hobie Part# 8090900
    COMP-TIP CAP PLUG
    Hobie
    NUT SQUARE 10-32 Murrays Part# 50-8051301 Hobie® factory replacement stainless steel 10-32 square nut can be used when mounting downhaul/halyard cleat on Hobie® 14 or 16. Also can be used for mounting H17 trampoline eye straps. Use 19-2910 screw. Hobie Part# 8051301
    NUT SQUARE 10-32
    Hobie
    Out of Stock
    Washer 5/16 X 9/16 Flat Murrays Part# 50-8080181 Hobie Part# 8080181
    WASHER FLAT 5/16 X 9/16"
    Hobie
    Out of Stock
    Cotter Pin 3/32 X 3/4 Murrays Part# 19-1015 Cotter pins are used on all Hobie, Nacra and Prindle rudder pins. They are used to secure the rudder pins. Compare to Hobie Cat® #8060111. Stainless steel cotter pin measures 3/32" x 3/4".
    COTTER PIN 3/32 X 3/4" SS
    Misc
    Recently viewed