Hobie 17 Front Crossbar Parts

23 products

    23 products
    Out of Stock
    Dolphin Striker Post H17
Murrays Part# 50-50212101
Hobie® factory replacement dolphin striker post for Hobie® 17
Hobie Part# 50212101
    H-17 DOLPHIN STRIKER POST
    Hobie
    $99.99
    Harken Swivel with Carbo Cam Bullseye

Murrays Part# 25-3010

Swivel cam cleats are ideal for main traveler control and up-release jib cleating systems. Cam cleats and fairleads should be selected on the basis of need. Order plastic base pads and flat head screws separately to mount to your front crossbar.
    HARKEN SWIVEL WITH CARBO CAM & BULLSEYE
    Harken
    $87.99
    Out of Stock
    H-17 SPORT SPREADER POLE END CAST
    Hobie
    $59.99
    Out of Stock
    Crossbar H17 Inboard Support
Murrays Part# 50-50213201
Hobie® factory replacement inboard support for Hobie® 17 crossbar
Hobie Part# 50213201
    H-17 CROSSBAR INBOARD SUPPORT
    Hobie
    $48.99
    Out of Stock
    Crossbar Insert Right Front & Left Rear H17 Black
Murrays Part# 50-50121511
Hobie® factory replacement right front/left rear crossbar insert for Hobie® 17
Hobie Part# 50121511
    H-17 CROSSBAR INSERT RF/LR
    Hobie
    $48.99
    Mast Ball H17  Wave
Murrays Part# 50-50212301
Hobie factory replacement mast ball for Hobie® 17 and Wave. Ball measures 1-1/2" diameter with a 9/16"-18 threaded hole. This ball can also be glued for use on Trac 16.
    H-17/WAVE MAST BALL
    Hobie
    $39.99
    Out of Stock
    H-17 SPORT SPREADER POLE YOKE
    Hobie
    $20.39
    Swivel Mount Base with Fasteners

Murrays Part# 007-1162

The offset base pad kit fits Hobie® and Prindle elliptical crossbars. Includes injection-molded plastic base and fasteners.

Replacement fasteners are also available (requires 3 self-tapping screws #19-1620, 1 machine screw #19-1516, and 1 nut #19-2016).

Hobie Cat® Part# 1162
    PRINDLE SWIVEL MOUNT BASE WITH FASTENERS
    Hobie
    $17.99
    3-Hole Pad Kit

Murrays Part# 001-0110

This base kit is for Harken®, Hobie® or Murray 360 cleats without swivel base adapters. Kit includes one 3-hole base, one swivel base adapter (#25-3001), plus three #10 FHSMS (#19-1626). Ronstan swivel 360 cleats include swivel base adapters, so this kit is not necessary. Fits Hobie® or Prindle elliptical crossbar.
    3-HOLE PAD KIT
    Murrays Sports
    $11.00
    Out of Stock
    Dolphin Striker Sleeve H17
Murrays Part# 50-50212201
Hobie® factory replacement dolphin striker compression sleeve for Hobie® 17
Hobie Part# 50212201
    H-17 DOLPHIN STRIKER SLEEVE
    Hobie
    $8.39
    Crossbar Plug H17
Murrays Part# 50-50262101
Hobie® factory replacement plug (cap) set for Hobie® 17 Crossbar
Hobie Part# 50262101
Sold in a package of 4
    H-17 CROSSBAR PLUG (4)
    Hobie
    $5.39
    Screw 5/16-18 X 2.5" Socket Head

Murrays Part# 50-8032221

Hobie® factory replacement socket head screw bolt is 5/16-18 x 2-1/2". Hobie 17 and 17 Sport front and rear crossbar bolt.

Hobie Part# 8032221
    SCREW 5/16 X 18 X 2.5" SOCKET HEAD
    Hobie
    $3.79
    Rivet CCC 6-6 (3/16 X 3/8) Countersunk
Murrays Part# 19-5024
Countersunk stainless steel 3/16" x 3/8" rivet for traveler tracks, etc.
Compare to Hobie Part # 8010201.
This rivets is what Hobie recommends for both the main traveler tack and the jib traveler track.
We also recommend using an 1/8" stop sleeve, part number 002-1041, as a spacer to help you apply pressure on the rivet inside the track, as the track is too narrow for most rivet guns to get far enough inside to apply pressure to the rivet.
    RIVET CCC 6-6 CSK
    Misc
    $1.99
    Small Fairlead: 1-1/4 X 1/2
Murrays Part# 23-0921
Stainless steel fairlead measurements:
A = 1-1/4" (31.4mm) between holes center-to-center
B = 1/2" (12.7mm) height
C = 3/16" (5mm) hole diameter
    RONSTAN SMALL FAIRLEAD: 1-1/4 X 1/2
    Ronstan
    $1.90
    Sealed Rivet CCP 6-8 (3/16 X 1/2)
Murrays Part# 19-5033S
Sealed rivets have a sealed end that does not require rivet casings to make them water tight. One and done, no casing needed, just insert and pop as you would a normal rivet, and your hole will be sealed.
Sealed Stainless steel 3/16" x 1/2" rounded pan head rivet. Compare to Hobie Cat® #8011231 Rivet and Hobie Cat® #8011291 rivet casing.
    RIVET CCP SEALED 6-8 (3/16 X 1/2)
    Misc
    $1.40
    Nut Jam 9/16-18 Low Profile

Murrays Part# 50-8050461

Hobie® factory replacement low-profile 9/16-18 jam nut is used on Hobie 17 dolphin striker.

Hobie Part# 8050461
    NUT JAM 9/16-18" LOW PROFILE
    Hobie
    $1.39
    Rivet CCP 6-8 (3/16 X 1/2)
Murrays Part# 19-5033
Stainless steel 3/16" x 1/2" rounded pan head rivet. Compare to Hobie Cat® #8011231.
    RIVET CCP 6-8 (3/16 X 1/2)
    Misc
    $0.85
    Out of Stock
    Nut Nylock 3/8-24

Murrays Part# 50-8050511

Replacement 3/8-24 nylock nut is used on Hobie® 14, 16 and 18 dolphin striker rods, as well as Hobie® 17 inboard support.

Hobie Part# 8050511
    NUT NYLOCK 3/8-24"
    Hobie
    $0.79
    Nut Nylock 5/16-18 Stainless Steel
Murrays Part# 19-2520
5/16-18 nylock nut is used on Hobie® rudders. The stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Compare to Hobie Cat® item #8050311 and 8050321 shroud anchor pin nut
Used with Hobie Getaway Bow Tang Bolt
    NUT NYLOCK 5/16-18 (SS)
    Misc
    $0.75
    FIBER TENDON SCREW
    Misc
    $0.49
    Used for tiller connection on Hobie Cats®. The stainless 1/4-20 stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Equivalent to Hobie #8050111. Also Equivalent to Nacra/Prindle F123 gudgon nut for all Prindle and older Nacras.
Applications:
Hobie 18 / H18:
Bow Tang Nut Qty: 6
Rudder Adjustment: 1
Hobie Getaway: Forestay Yoke Nut
    NYLOCK NUT 1/4-20 SS
    Misc
    $0.45
    Screw PHMS #10-32 X 1 Stainless Steel Slot Head
Murrays Part# 19-2915
Stainless steel, pan head #10-32 x 1" machine screw with slot is used as dolphin striker screw on all Prindles. Replaces Murrays item #56-F112.
Also used in some Hobie Applications, compare to 8030111 Hobie Part.
Applications:
H18/18 SX/16 and Getaway
Tiller Hinge Screw: 2
    SCREW PHMS #10-32 X 1" (SS)
    Misc
    $0.36
    NUT SQUARE 10-32

Murrays Part# 50-8051301


Hobie® factory replacement stainless steel 10-32 square nut can be used when mounting downhaul/halyard cleat on Hobie® 14 or 16.

Also can be used for mounting H17 trampoline eye straps. Use 19-2910 screw.

Hobie Part# 8051301
    NUT SQUARE 10-32
    Hobie
    $0.29
    Recently viewed