Hobie 16 Mast Parts

Hobie 16 Mast Parts

71 products

    Parts used with the H16 Mast

    71 products
    MURRAYS H-16 HALYARD GRIP KIT The Murrays H16 Halyard grip kit is a mast hook that hold the jib halyard off center on the mast so that the jib battens don't hang up on the jib halyard when tacking.  Mostly used on the Hobie 16. Compare to Hobie part number 114
    MURRAYS H-16 HALYARD GRIP KIT
    Murrays Sports
    HOBIE HALYARD GRIP KIT The Hobie Halyard grip kit is a mast hook that hold the jib halyard off center on the mast so that the jib battens don't hang up on the jib halyard when tacking. Mostly used on the Hobie 16. Hobie part number 114
    HOBIE HALYARD GRIP KIT
    Hobie
    H18 Mast Head/Base Sheave Murrays Part# 50-60620000 Factory replacement sheave for Hobie 18 mast head/base and outhaul assembly. Specs: 1" Diameter x 3/8" wide and 1/4" hole. Also used as traveler control line turning sheave on 2005 and newer Hobie 16 sailboats. Applications: Hobie 18 - Mast head halyard sheave ; mast base halyard sheave ; outhaul car sheaves. Hobie 16 - Jib Traveler line sheave. (in the H16 Race Corner Castings) use 50-8011251 Rivet
    H-18 MAST HEAD/BASE SHEAVE
    Hobie
    Mast Cleat Murrays Part# 011-6481 The Mast Cleat is a can be used as a downhaul / halyard cleat on a Hobie 14 and or 16. Compare to Hobie Cat® factory item #10730000. 31mm Center to Center.
    MAST CLEAT
    Murrays Sports
    Ronstan Stainless Steel Bow Shackle, 3/16" Pin, Coined Head Murrays Part# 21-0634 Solid stainless steel bow shackle has 3/16" diameter pin.  UDL BL - The “Uniformly Distributed Load” breaking load of the shackle; the load is applied across the full span of the shackle pin. PL BL - The “Point Load” breaking load of the shackle; the load is only applied at the center or one side of the shackle pin.
    Ronstan bow shackle measurements
    RONSTAN STAINLESS STEEL BOW SHACKLE, 3/16" PIN, COINED HEAD
    Ronstan
    Quick-Release Pin Detent 1/4 X 1-1/2 Murrays Part# 18-4D150 The Quick-Release Pin Detent 1/4 X 1-1/2 is an economical, quick connection for Hobie 16 mast step pin. A spring-loaded ball exerts sufficient pressure to help avoid accidental release. Measurements are 1/4″ diameter x 1-1/2″ maximum grip length (distance from the shoulder to the locking ball bearings).
    QUICK RELEASE DETENT PIN 1/4 X 1-1/2"
    Misc
    Out of Stock
    H-16 FOAM MAST PLUG
    Hobie
    Out of Stock
    H16 Mast Seal Plate Murrays Part# 50-21090001 Hobie® factory replacement mast seal plate for Hobie® 16.
    H-16 MAST SEAL PLATE
    Hobie
    Murrays Part# 007-1051 The standard replacement deck plate for the traveler on all Hobie® 14, 16 and newer 17's. Hobie Cat® factory item #11870000.  Uses a 3/16 x 1/2" clevis pin to attach to the main sheet system. Also used in Hobie 14 and Hobie 16 upgrade downhaul systems to secure lower block. Sold individually
    TRACKER DECK PLATE (EA)
    Hobie
    Out of Stock
    H16 Masthead Sheave Spacer Murrays Part# 50-20614231 H16 Masthead Sheave Spacer. This is a replacement bearing surface for the comptip masthead sheaves in H16 mastheads. Fits Hobie Getaway Masthead Sheaves Hobie Part# 20644231
    H-16 MASTHEAD SHEAVE SPACER
    Hobie
    Out of Stock
    H16 Mast Head Sheave Pin  Hobie Part# 50-10630001 This is a hollow rivet for installing the Hobie 16 masthead sheave on an all aluminum mast, large pulley masthead. Requires special tools or creative minded sailor to improvise their own installation method
    H-16 MAST HEAD SHEAVE PIN
    Hobie
    3/16 X 7/8" Clevis Pin Murrays Part# 22-9806 3/16 x 7/8 Clevis Pin.  H16 gooseneck shackle clevis pin. Hobie Part# 8020061
    3/16 X 7/8" CLEVIS PIN
    Misc
    3/16 X 1/2" Clevis Pin Murrays Part# 22-9801 Stainless steel clevis pin measures 3/16" diameter x 1/2" grip length (shoulder to the split ring hole). Prindle / Nacra Part# 9412 Compare to Hobie Cat® Part# 8020041
    3/16 x 1/2" CLEVIS PIN
    Misc
    Bolt Hex Head 1/4-20 X 3.5" Stainless Steel Murrays Part# 19-2224 Stainless steel hex head bolt measures 1/4-20 x 3-1/2" Pylon Bolt for newer H16 Hobie Part# 8040361
    BOLT 1/4-20 X 3.5" (SS)
    Misc
    Stainless steel clevis pin. Measurement is 1/4" diameter x 5/8" grip length. Hobie part number 8020361, 8020381 and 8020380.
    1/4 X 5/8" Clevis Pin Murrays Part# 22-9802 Stainless steel clevis pin. Measurement is 1/4" diameter x 5/8" grip length (shoulder to the split ring hole).  Uses: Most commonly used to connect shrouds and forestays to 7 or 10 hole shroud adjusters on Hobie, Nacra and Prindle catamarans. Hobie 18 gooseneck vertex pin Hobie 18 outhaul car sheave pin Hobie Part# 8020361, 8020381 and 8020380
    1/4 X 5/8" CLEVIS PIN
    Misc
    Decal Mast Caution Orange Murrays Part# 13440010 Hobie® factory decal attaches to mast as a reminder to watch for overhead power lines when sailing and/or launching your boat. Hobie Part# 13440010
    ORANGE MAST CAUTION DECAL
    Hobie
    Out of Stock
    Black Mast Caution Decal Murrays Part# 50-13440000 The Decal Mast Caution Black Hobie® factory caution decal attaches to mast as a reminder to watch for overhead power lines when sailing and/or launching your boat.
    BLACK MAST CAUTION DECAL
    Hobie
    Sealed Rivet CCP 6-8 (3/16 X 1/2) Murrays Part# 19-5033S Sealed rivets have a sealed end that does not require rivet casings to make them water tight. One and done, no casing needed, just insert and pop as you would a normal rivet, and your hole will be sealed. Sealed Stainless steel 3/16" x 1/2" rounded pan head rivet. Compare to Hobie Cat® #8011231 Rivet and Hobie Cat® #8011291 rivet casing.
    RIVET CCP SEALED 6-8 (3/16 X 1/2)
    Misc
    Sealed Stainless Steel 3/16" x 3/8" Pan Head Rivet Murrays Part# 19-5032S Sealed rivets have a sealed end that does not require rivet casings to make them water tight. One and done, no casing needed, just insert and pop as you would a normal rivet, and your hole will be sealed. Among other uses, the Stainless steel 3/16" x 3/8" pan head rivet can be used when Hobie® rivet #8010131 is specified: Hobie 14 (2) or 16 (4) mast head Hobie Wave/Getaway/14/16/17/18/18SX/ mast base (4) Hobie 14/16
    RIVET CCP SEALED 6-6 (3/16 X 3/8)
    Misc
    Hobie rivet casings sleeves seal rivets to prevent water penetration. When used with a rivet they seal the hole to prevent water from getting through the center of the rivet. Rivet Casings are recommended for use on all rivets on the mast to keep the mast water tight. Compatible with all 3/16 diameter rivets up to 5/8" long. Compatible with all rivets on Hobie, Nacra and Prindle catamarans except traveler tracks. Requires 13/64" hole. Hobie part number 8011291, 8011290, also called rivet cap.
    RIVET CASING 6-10(3/16 X 5/8)
    Hobie
    Rivet Semi 3/16x27/32 Stainless Steal Murrays Part# 50-8012062
    RIVET SEMI
    Hobie
    Rivet CCP 6-10 (3/16 X 5/8) Murrays Part# 19-5034 Stainless steel 3/16" x 5/8" rounded pan head rivet. Compare to Hobie Cat® #8010121. Halyard mast cleat rivet
    RIVET CCP 6-10 (3/16 X 5/8)
    Misc
    Rivet CCP 6-8 (3/16 X 1/2) Murrays Part# 19-5033 Stainless steel 3/16" x 1/2" rounded pan head rivet. Compare to Hobie Cat® #8011231.
    RIVET CCP 6-8 (3/16 X 1/2)
    Misc
    RIVET CCP 6-6 (3/16 X 3/8) Murrays Part# 19-5032 Stainless steel 3/16" x 3/8" pan head rivet Among other uses, the Stainless steel 3/16" x 3/8" pan head rivet can be used when Hobie® rivet #8010131 is specified: Hobie 14 (2) or 16 (4) mast head Hobie Wave/Getaway/14/16/17/18/18SX/ mast base (4) Hobie 14/16 rudder upper casting (2) Hobie 14/16 tiller end cap (2) Hobie 14/16 boom front end cap (3) Pair with stainless steal rivet casings to seal the holes when using on the mast.
    RIVET CCP 6-6 (3/16 X 3/8)
    Misc
    Nut Nylock 5/16-18 Stainless Steel Murrays Part# 19-2520 5/16-18 nylock nut is used on Hobie® rudders. The stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Compare to Hobie Cat® item #8050311 and 8050321 shroud anchor pin nut Used with Hobie Getaway Bow Tang Bolt
    NUT NYLOCK 5/16-18 (SS)
    Misc
    3/16 - 1/4" Split Ring Murrays Part# 22-9492 Stainless steel split ring (ring ding) for 3/16″-1/4″ diameter clevis pin. This is the standard size Hobie split ring used all over the boats, most commonly on the shrouds, forestay and roller furler Medium Split ring Dimensions: 5/8″ Diameter Material: 316 Stainless steel. This is the most common size Split ring on Hobie, Nacra and Prindle Catamarans. 20860000 Medium Clevis Ring.
    3/16-1/4" SPLIT RING
    Misc
    Used for tiller connection on Hobie Cats®. The stainless 1/4-20 stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Equivalent to Hobie #8050111. Also Equivalent to Nacra/Prindle F123 gudgon nut for all Prindle and older Nacras. Applications: Hobie 18 / H18: Bow Tang Nut Qty: 6 Rudder Adjustment: 1 Hobie Getaway: Forestay Yoke Nut
    NYLOCK NUT 1/4-20 SS
    Misc
    Nut Nylock #10-32 Stainless Steel Thick Murrays Part# 19-2515 Mainsheet block replacement nut. The stainless hex nut with nylock insert will not rust or work loose if properly installed. Fits Hobie Main Traveler Car. Fits Hobie Tiller Hinge Screw. Fits Hobie Masthead Sheave Screw H16 Hobie Getaway Compare to Hobie Part Number 8050201
    NUT NYLOCK #10-32 (SS) THICK
    Misc
    Screw PHMS #10-32 X 1 Stainless Steel Slot Head Murrays Part# 19-2915 Stainless steel, pan head #10-32 x 1" machine screw with slot is used as dolphin striker screw on all Prindles. Replaces Murrays item #56-F112. Also used in some Hobie Applications, compare to 8030111 Hobie Part. Applications: H18/18 SX/16 and Getaway Tiller Hinge Screw: 2
    SCREW PHMS #10-32 X 1" (SS)
    Misc
    Comptip Cap Plug Murrays Part# 50-8090900 This part is used to seal the hole in the Comptip of a Hobie cat after the expanding foam has been put in. Hobie Part# 8090900
    COMP-TIP CAP PLUG
    Hobie
    NUT SQUARE 10-32 Murrays Part# 50-8051301 Hobie® factory replacement stainless steel 10-32 square nut can be used when mounting downhaul/halyard cleat on Hobie® 14 or 16. Also can be used for mounting H17 trampoline eye straps. Use 19-2910 screw. Hobie Part# 8051301
    NUT SQUARE 10-32
    Hobie
    Recently viewed