Hobie 14 Rear Crossbar Parts

33 products

    Rear Crossbar Parts for your Hobie 14

    33 products
    X-BAR REAR H14 BK W/O CAST
    Hobie
    Out of Stock
    Tracker Traveler Kit Murrays Part# 007-1040 Traveler car assembly for Hobie® 14 or 16 includes #07-1050 tracker car, swivel cam, mounting plate, line and fasteners. Standard on Hobie 14/16/17's made prior to 1994 but after the early 70s. This kit includes all the parts to rebuild your rear traveler system on an old worn out boat, or update some of the REALLY old traveler car systems on the early H14 or H16 boats.
    TRACKER TRAVELER KIT
    Murrays Sports
    Out of Stock
    Corner Casting Race Rear Right H14/16 Murrays Part# 50-10202011 Hobie® factory replacement left rear corner casting (#3) for Hobie® 14 or 16. This part replaces Hobie Cat's discontinued item #10200011. Use six 6-8 rivets (#19-5033) for installation. Rear Crossbar casting for Hobie 16.
    CORNER CASTING R/R H14/16
    Hobie
    CORNER CASTING RACE L/R 4
    Hobie
    MAIN TRAVELER TRACK BK (DEEP)
    Hobie
    TRACKER CAR COMPLETE NEW (POST93)
    Hobie
    Out of Stock
    Tracker Car Complete (Pre-1994) Murrays Part# 007-1050 This tracker car is the standard replacement part for all 1993 and earlier Hobie® 14, 16 and 17 main tracker traveler assemblies. Includes 2-3 rivets where required. Hobie Cat® factory item #105.
    TRACKER CAR COMPLETE (PRE'94)
    Hobie
    TRACKER:BOTTOM ROLLER (POST93)
    Hobie
    Out of Stock
    Tracker: Bottom Roller (Pre-1994) Murrays Part# 007-1060 The standard replacement bottom roller for all 1993 and earlier Hobie® 14 and 16s. Includes two rivets. Hobie Cat® factory item #106.
    TRACKER: BOTTOM ROLLER (PRE 94)
    Hobie
    Out of Stock
    Aluminum Adjustable tiller extension for Hobie, Nacra and Prindle catamarans. Compare to Hobie 20550001 Hobie hot stick
    ALUMINUM TILLER EXTENSION 50"-95"
    Murrays Sports
    Harken Swivel with Carbo Cam Bullseye Murrays Part# 25-3010 Swivel cam cleats are ideal for main traveler control and up-release jib cleating systems. Cam cleats and fairleads should be selected on the basis of need. Order plastic base pads and flat head screws separately to mount to your front crossbar.
    HARKEN SWIVEL W/CARBO CAM & BULLSEYE
    Harken
    TRACKER: HINGE UPRIGHT (EA)so
    Hobie
    QR PIN DELUXE 3/16 X 3/4
    Misc
    QR PIN STANDARD 3/16 X 3/4
    Misc
    HOBIE TRACKER: SHEAVE REPLACEMENT KIT
    Hobie
    SWIVEL MOUNT BASE W/FASTENERS
    Hobie
    Tracker: Sheave The standard replacement sheave for the tracker traveler on all Hobie® 14, 16 and newer 17's. Hobie® factory item #11880000. Tracker is the term used by Hobie for the rear traveler car. This can also be considered a traveler sheave. Fits Hobie Getaway Main Traveler Car.
    HOBIE TRACKER TRAVELER SHEAVE
    Hobie
    Murrays Part#  007-1051 The standard replacement deck plate for the traveler on all Hobie® 14, 16 and newer 17's. Hobie Cat® factory item #11870000.  Uses a 3/16 x 1/2" clevis pin to attach to the main sheet system. Also used in Hobie 14 and Hobie 16 upgrade downhaul systems to secure lower block. Sold individually
    TRACKER: DECK PLATE (EA)
    Hobie
    TRACKER: SHEAVE SPACER (EA)
    Hobie
    TRACKER: HINGE PIN (EA)
    Hobie
    CLEVIS PIN 3/16 X 5/8
    Misc
    CLEVIS PIN 3/16 X 1/2
    Misc
    BOLT 5/16 X 18 X3.5"
    Misc
    Rivet CCC 6-6 (3/16 X 3/8) Countersunk Murrays Part# 19-5024 Countersunk stainless steel 3/16" x 3/8" rivet for traveler tracks, etc. Compare to Hobie Part # 8010201. This rivets is what Hobie recommends for both the main traveler tack and the jib traveler track. We also recommend using an 1/8" stop sleeve, part number 002-1041, as a spacer to help you apply pressure on the rivet inside the track, as the track is too narrow for most rivet guns to get far enough inside to apply pressure to the rivet.
    RIVET CCC 6-6 CSK
    Misc
    Small Fairlead: 1-1/4 X 1/2 Murrays Part# 23-0921 Stainless steel fairlead measurements: A = 1-1/4" (31.4mm) between holes center-to-center B = 1/2" (12.7mm) height C = 3/16" (5mm) hole diameter
    SMALL FAIRLEAD: 1-1/4 X 1/2
    Ronstan
    BOLT HEX HD 5/16-18 X 1.5"
    Misc
    Sealed Rivet CCP 6-8 (3/16 X 1/2) Murrays Part# 19-5033S Sealed rivets have a sealed end that does not require rivet casings to make them water tight. One and done, no casing needed, just insert and pop as you would a normal rivet, and your hole will be sealed. Sealed Stainless steel 3/16" x 1/2" rounded pan head rivet. Compare to Hobie Cat® #8011231 Rivet and Hobie Cat® #8011291 rivet casing.
    RIVET CCP SEALED 6-8 (3/16 X 1/2)
    Misc
    Rivet CCP 6-8 (3/16 X 1/2) Murrays Part# 19-5033 Stainless steel 3/16" x 1/2" rounded pan head rivet. Compare to Hobie Cat® #8011231.
    RIVET CCP 6-8 (3/16 X 1/2)
    Misc
    3/16 - 1/4" Split Ring Murrays Part# 22-9492 Stainless steel split ring (ring ding) for 3/16″-1/4″ diameter clevis pin.  This is the standard size Hobie split ring used all over the boats, most commonly on the shrouds, forestay and roller furler Medium Split ring Dimensions: 5/8″ Diameter Material: 316 Stainless steel. This is the most common size Split ring on Hobie, Nacra and Prindle Catamarans.
    SPLIT RING 3/16-1/4"
    Misc
    Nut Nylock 5/16-18 Stainless Steel Murrays Part# 19-2520 5/16-18 nylock nut is used on Hobie® rudders. The stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Compare to Hobie Cat® item #8050311 and 8050321 shroud anchor pin nut Used with Hobie Getaway Bow Tang Bolt
    NUT NYLOCK 5/16-18 (SS)
    Misc
    1/2 BALL (NYLON) - Hobie half round washer spacer tiller connector - Hobie part number 11510000 HOBIE HALF SPHERE TILLER CONNECTOR
    1/2 BALL (NYLON)
    Murrays Sports
    Screw PHMS #10-32 X 1 Stainless Steel Slot Head Murrays Part# 19-2915 Stainless steel, pan head #10-32 x 1" machine screw with slot is used as dolphin striker screw on all Prindles. Replaces Murrays item #56-F112. Also used in some Hobie Applications, compare to 8030111 Hobie Part. Applications: H18/18 SX/16 and Getaway Tiller Hinge Screw: 2
    SCREW PHMS #10-32 X 1 (SS) SLOT HEAD
    Misc
    NUT SQUARE 10-32
    Hobie