Hobie 14 Front Crossbar Parts

28 products

    Front Crossbar parts for your Hobie 14

    28 products
    Out of Stock
    X-BAR FRONT H14 BK W/O CAST so
    Hobie
    Corner Casting Front Left Black H14/16 Murrays Part# 50-10150011 Hobie® factory replacement left front corner casting (#1) for Hobie® 14 or 16. Requires six 6-8 rivets (item #19-5033) for installation
    H-14/16 CORNER CASTING FRONT LEFT-BLACK
    Hobie
    H14/16 Mast Bearing (Pack of 100) Murrays Part# 001-2042 Teflon® mast bearings for Hobie® 14 or 16 are .06" thick and will form to mast base with first use. Package of 100 mast chips.
    H14/16 MAST BEARING (100-PKG)
    Murrays Sports
    Out of Stock
    H14/Wave Mast Step Murrays Part# 50-10170011 Mast step for Hobie 14 (without threaded post) and Wave (96 and older). Hobie® factory replacement part. If you have a H14 with threaded post order #50-20200011 (see below). Requires four 6-6 rivets (item #19-5032).
    H14/WAVE MAST STEP
    Hobie
    Out of Stock
    H14/16 Mast Step-Black Murrays Part# 50-20200011 This is a factory Hobie 14*/16 Mast Step Black replacement. For Hobie 14s and Hobie 16s.  This is the post 2004 version. The first hardware change was in the early 80s. The mast step was angled further back and the mast base was adjusted to match. If you are replacing an original pre-1980 mast step you will need new rigging to accommodate the increased mast rake.
    H-14/16 MAST STEP-BLACK
    Hobie
    Murrays Original Hobie 14 & 16 Jib traveler car for pre 1994 boats with the external track on the front crossbar. 21230000
    MURRAYS H-14/16 JIB TRAVELER CAR
    Murrays Sports
    H14 Dolphin Striker Rod
    Murrays Sports
    Harken Swivel with Carbo Cam Bullseye Murrays Part# 25-3010 Swivel cam cleats are ideal for main traveler control and up-release jib cleating systems. Cam cleats and fairleads should be selected on the basis of need. Order plastic base pads and flat head screws separately to mount to your front crossbar.
    HARKEN SWIVEL WITH CARBO CAM & BULLSEYE
    Harken
    H16 Dolphin Striker Post Murrays Part# 50-20140001 Hobie® factory replacement dolphin striker post fits all Hobie® 16 mast steps (older and newer)
    H-16 DOLPHIN STRIKER POST
    Hobie
    MAST STEP LINK KIT H14/16 Hobie part number 21380001
    H-14/16 MAST STEP LINK KIT
    Hobie
    V JAM CLEAT BOOM (3/16" HOLES)
    Hobie
    Swivel Mount Base with Fasteners Murrays Part# 007-1162 The offset base pad kit fits Hobie® and Prindle elliptical crossbars. Includes injection-molded plastic base and fasteners. Replacement fasteners are also available (requires 3 self-tapping screws #19-1620, 1 machine screw #19-1516, and 1 nut #19-2016). Hobie Cat® Part# 1162
    SWIVEL MOUNT BASE WITH FASTENERS
    Hobie
    H14/16 Bow Tang Murrays Part# 50-20120000 Hobie® factory replacement bow tang for Hobie® 14, 16 or Getaway. Use #19-3530 screw and #19-2520 nylock nut on Hobie 16; use #19-3530 screw on Hobie 14. The original Hobie® 14 tang is no longer available. 20120010
    H-14/16 BOW TANG
    Hobie
    3-Hole Pad Kit Murrays Part# 001-0110 This base kit is for Harken®, Hobie® or Murray 360 cleats without swivel base adapters. Kit includes one 3-hole base, one swivel base adapter (#25-3001), plus three #10 FHSMS (#19-1626). Ronstan swivel 360 cleats include swivel base adapters, so this kit is not necessary. Fits Hobie® or Prindle elliptical crossbar.
    3-HOLE PAD KIT
    Murrays Sports
    Hobie 16 mast bearings. Teflon mast chips, Hobie part number 11110005
    Hobie mast chips - 11110005
    H-14/16 MAST BEARING (3-PKG)
    Murrays Sports
    Dolphin Striker Eye Bolt H14 Murrays PN 001-0106 This part is used as part of the Murrays H14 Dolphin Striker Kit. Replacement stainless steel post for #01-2083 dolphin striker for Hobie® 14. 19-2524 nylock nut is needed and not included with this part.
    H-14 DOLPHIN STRIKER EYE BOLT
    Murrays Sports
    Bolt 5/16 X 18 X3.5" Murrays Part# 50-8040371 Hobie® factory replacement 5/16-18 x 3-7/16" bolt. Pylon bolt for Hobie® 14 and older 16 (1994 and prior; starting in 1995, boats had newer style castings/pylons). Hobie Part# 8040371
    BOLT 5/16 X 18 X3.5"
    Hobie
    Bolt Hex Head 5/16-18 X 2.50" Stainless Steel Murrays Part# 19-2231 Stainless steel rudder bolt for all Hobie® Cats measures 5/16-18 x 2.50".  Used on Hobie Getaway Bow Spreader - Bow Tang Bolt. Rudder bolt for both the upper and lower rudder casting. Compare to Hobie Cat® Part# 8040341
    BOLT HEX HEAD 5/16-18 X 2.50" SS
    Misc
    Rivet CCC 6-6 (3/16 X 3/8) Countersunk Murrays Part# 19-5024 Countersunk stainless steel 3/16" x 3/8" rivet for traveler tracks, etc. Compare to Hobie Part # 8010201. This rivets is what Hobie recommends for both the main traveler tack and the jib traveler track. We also recommend using an 1/8" stop sleeve, part number 002-1041, as a spacer to help you apply pressure on the rivet inside the track, as the track is too narrow for most rivet guns to get far enough inside to apply pressure to the rivet.
    RIVET CCC 6-6 CSK
    Misc
    Small Fairlead: 1-1/4 X 1/2 Murrays Part# 23-0921 Stainless steel fairlead measurements: A = 1-1/4" (31.4mm) between holes center-to-center B = 1/2" (12.7mm) height C = 3/16" (5mm) hole diameter
    RONSTAN SMALL FAIRLEAD: 1-1/4 X 1/2
    Ronstan
    Sealed Rivet CCP 6-8 (3/16 X 1/2) Murrays Part# 19-5033S Sealed rivets have a sealed end that does not require rivet casings to make them water tight. One and done, no casing needed, just insert and pop as you would a normal rivet, and your hole will be sealed. Sealed Stainless steel 3/16" x 1/2" rounded pan head rivet. Compare to Hobie Cat® #8011231 Rivet and Hobie Cat® #8011291 rivet casing.
    RIVET CCP SEALED 6-8 (3/16 X 1/2)
    Misc
    Rivet CCP 6-8 (3/16 X 1/2) Murrays Part# 19-5033 Stainless steel 3/16" x 1/2" rounded pan head rivet. Compare to Hobie Cat® #8011231.
    RIVET CCP 6-8 (3/16 X 1/2)
    Misc
    Nut Nylock 3/8-24 Murrays Part# 50-8050511 Replacement 3/8-24 nylock nut is used on Hobie® 14, 16 and 18 dolphin striker rods, as well as Hobie® 17 inboard support. Hobie Part# 8050511
    NUT NYLOCK 3/8-24"
    Hobie
    Nut Nylock 5/16-18 Stainless Steel Murrays Part# 19-2520 5/16-18 nylock nut is used on Hobie® rudders. The stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Compare to Hobie Cat® item #8050311 and 8050321 shroud anchor pin nut Used with Hobie Getaway Bow Tang Bolt
    NUT NYLOCK 5/16-18 (SS)
    Misc
    Rivet CCP 6-4 (3/16 X 1/4) Murrays Part# 19-5031 Stainless steel 3/16" x 1/4" rounded pan head rivet. Compare to Hobie Cat® #8010181. This is a common rivet used on many extrusions. Hobie, Nacra, Prindle masts and booms. Pair with a rivet casing to seal the rivet hole when used on masts. All Hobie mast hounds, tangs, heads, and cheek blocks. Used with Hobie Getaway Bow Spreader Plates Used on Hobie Getaway FWD and REAR Crossbar Stop Plates
    RIVET CCP 6-4 (3/16 X 1/4)
    Misc
    Used for tiller connection on Hobie Cats®. The stainless 1/4-20 stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Equivalent to Hobie #8050111. Also Equivalent to Nacra/Prindle F123 gudgon nut for all Prindle and older Nacras. Applications: Hobie 18 / H18: Bow Tang Nut Qty: 6 Rudder Adjustment: 1 Hobie Getaway: Forestay Yoke Nut
    NYLOCK NUT 1/4-20 SS
    Misc
    Screw PHMS #10-32 X 1 Stainless Steel Slot Head Murrays Part# 19-2915 Stainless steel, pan head #10-32 x 1" machine screw with slot is used as dolphin striker screw on all Prindles. Replaces Murrays item #56-F112. Also used in some Hobie Applications, compare to 8030111 Hobie Part. Applications: H18/18 SX/16 and Getaway Tiller Hinge Screw: 2
    SCREW PHMS #10-32 X 1" (SS)
    Misc
    NUT SQUARE 10-32 Murrays Part# 50-8051301 Hobie® factory replacement stainless steel 10-32 square nut can be used when mounting downhaul/halyard cleat on Hobie® 14 or 16. Also can be used for mounting H17 trampoline eye straps. Use 19-2910 screw. Hobie Part# 8051301
    NUT SQUARE 10-32
    Hobie