Getaway Rear Crossbar Parts

24 products

    Parts for the rear crossbar of your Hobie Getaway

    24 products
    TRACKER CAR COMPLETE NEW (POST93)
    Hobie
    Tracker: Bottom Roller (Post-1993) Murrays Part# 007-0112 Bottom roller with rivets for the tracker car on 1993 and later Hobie® 14, 16 and 17 's. This part allows you to rebuild your existing Hobie Traveler car by just replacing the track rollers and keeping the top half. This part can be installed on older boats if the matching Deep Track is installed as well. Fits Hobie Getaway Traveler Car. Hobie Cat Part# 112
    TRACKER BOTTOM ROLLER (POST 93)
    Hobie
    Aluminum Adjustable tiller extension for Hobie, Nacra and Prindle catamarans. Compare to Hobie 20550001 Hobie hot stick
    ALUMINUM TILLER EXTENSION 50"-95"
    Murrays Sports
    Harken Swivel with Carbo Cam Bullseye Murrays Part# 25-3010 Swivel cam cleats are ideal for main traveler control and up-release jib cleating systems. Cam cleats and fairleads should be selected on the basis of need. Order plastic base pads and flat head screws separately to mount to your front crossbar.
    HARKEN SWIVEL WITH CARBO CAM & BULLSEYE
    Harken
    Out of Stock
    Getaway Aft Crossbar End Cap Murrays Part# 50-37201021 Hobie® factory replacement rear crossbar casting end cap for Hobie® Getaway.
    GETAWAY AFT CROSSBAR END CAP
    Hobie
    Tracker Hinge Upright Murrays Part# 007-1054 The standard replacement hinge upright for the tracker on all Hobie® 14, 16 and newer 17's. Fits: Hobie Getaway Main Traveler Car Hobie Cat® Part# 11840100
    TRACKER UPRIGHT HINGE
    Hobie
    Out of Stock
    H20 & Getaway Swivel Travel Cam Plate Murrays Part# 50-37760041 Hobie® factory replacement swivel cam plate for Getaway. This bent plate is also used on the Hobie® 20 to convert mainsheet traveler control to Hobie® 16/18 style with control cleat (360-degree swivel cam) on main rear beam instead of on mainsheet traveler car. This is your answer to preventing the traveler from coming toward you when you're trying to pull in the mainsheet on your Hobie® 20.
    H-20 & GETAWAY SWIVEL TRAVEL CAM PLATE
    Hobie
    Tracker Traveler Sheave Replacement Kit Murrays Part# 007-1059 The standard replacement sheave for the tracker traveler on all Hobie® 14, 16 and newer 17's.  Tracker is the term used by Hobie for the rear traveler car. This can also be considered a traveler sheave. Fits Hobie Getaway Main Traveler Car. Hobie® Part# 11880000
    TRACKER TRAVELER SHEAVE REPLACEMENT KIT
    Hobie
    Eyelet Post H20 Murrays Part# 50-41220001 The Eyelet Post H20 Hobie® factory replacement eyelet post for Hobie® 20 rear crossbar. This item replaces tie button for Inter cats #56-9882. Fits Hobie Getaway Rear Crossbar
    H-20 EYELET POST
    Hobie
    Tracker: Sheave The standard replacement sheave for the tracker traveler on all Hobie® 14, 16 and newer 17's. Hobie® factory item #11880000. Tracker is the term used by Hobie for the rear traveler car. This can also be considered a traveler sheave. Fits Hobie Getaway Main Traveler Car.
    TRACKER TRAVELER SHEAVE
    Hobie
    Murrays Part# 007-1051 The standard replacement deck plate for the traveler on all Hobie® 14, 16 and newer 17's. Hobie Cat® factory item #11870000.  Uses a 3/16 x 1/2" clevis pin to attach to the main sheet system. Also used in Hobie 14 and Hobie 16 upgrade downhaul systems to secure lower block. Sold individually
    TRACKER DECK PLATE (EA)
    Hobie
    Tracker Sheave Spacer Murrays Part# 007-1052 The standard replacement sheave spacer for the traveler on all Hobie® 14, 16 and newer 17's. Sold Individually Hobie Cat® Part# 11860000.
    TRACKER SHEAVE SPACER (EA)
    Hobie
    TRACKER HINGE PIN
    Hobie
    3/16 X 1/2" Clevis Pin Murrays Part# 22-9801 Stainless steel clevis pin measures 3/16" diameter x 1/2" grip length (shoulder to the split ring hole). Prindle / Nacra Part# 9412 Compare to Hobie Cat® Part# 8020041
    3/16 x 1/2" CLEVIS PIN
    Misc
    Rivet CCC 6-6 (3/16 X 3/8) Countersunk Murrays Part# 19-5024 Countersunk stainless steel 3/16" x 3/8" rivet for traveler tracks, etc. Compare to Hobie Part # 8010201. This rivets is what Hobie recommends for both the main traveler tack and the jib traveler track. We also recommend using an 1/8" stop sleeve, part number 002-1041, as a spacer to help you apply pressure on the rivet inside the track, as the track is too narrow for most rivet guns to get far enough inside to apply pressure to the rivet.
    RIVET CCC 6-6 CSK
    Misc
    Bolt Hex Head 5/16-18 X 1.5" Murrays Part# 19-2229 Use this stainless steel, 5/16-18 x 1-1/2" hex head bolt as beam strap bolt for Nacra. Substitute for Nacra Sailing factory item #30358. This bolt is also used to hold the cam stop plate on a Hobie Rudder Upper casting. Replaces Hobie Cat® Part# 8040301 and Murrays Part# 56-F164
    BOLT HEX HEAD 5/16-18 X 1.5"
    Misc
    Sealed Rivet CCP 6-8 (3/16 X 1/2) Murrays Part# 19-5033S Sealed rivets have a sealed end that does not require rivet casings to make them water tight. One and done, no casing needed, just insert and pop as you would a normal rivet, and your hole will be sealed. Sealed Stainless steel 3/16" x 1/2" rounded pan head rivet. Compare to Hobie Cat® #8011231 Rivet and Hobie Cat® #8011291 rivet casing.
    RIVET CCP SEALED 6-8 (3/16 X 1/2)
    Misc
    RIVET MCP 6-8 3/16x1/2" PH Murrays Part# 50-8011231 Hobie® factory 6-8 heavy duty rivet requires a rivet tool for installation. 3/16" x 1/2" pan head. Fits Hobie Getaway Eyelet Post. Fits Hobie 20 Eyelet Post. Mounts Wave Mast Step Hobie part number 8011231
    RIVET MCP 6-8 3/16x1/2" PH
    Hobie
    Nut Nylock 5/16-18 Stainless Steel Murrays Part# 19-2520 5/16-18 nylock nut is used on Hobie® rudders. The stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Compare to Hobie Cat® item #8050311 and 8050321 shroud anchor pin nut Used with Hobie Getaway Bow Tang Bolt
    NUT NYLOCK 5/16-18 (SS)
    Misc
    3/16 - 1/4" Split Ring Murrays Part# 22-9492 Stainless steel split ring (ring ding) for 3/16″-1/4″ diameter clevis pin. This is the standard size Hobie split ring used all over the boats, most commonly on the shrouds, forestay and roller furler Medium Split ring Dimensions: 5/8″ Diameter Material: 316 Stainless steel. This is the most common size Split ring on Hobie, Nacra and Prindle Catamarans. 20860000 Medium Clevis Ring.
    3/16-1/4" SPLIT RING
    Misc
    Rivet CCP 6-4 (3/16 X 1/4) Murrays Part# 19-5031 Stainless steel 3/16" x 1/4" rounded pan head rivet. Compare to Hobie Cat® #8010181. This is a common rivet used on many extrusions. Hobie, Nacra, Prindle masts and booms. Pair with a rivet casing to seal the rivet hole when used on masts. All Hobie mast hounds, tangs, heads, and cheek blocks. Used with Hobie Getaway Bow Spreader Plates Used on Hobie Getaway FWD and REAR Crossbar Stop Plates
    RIVET CCP 6-4 (3/16 X 1/4)
    Misc
    Out of Stock
    FIBER TENDON SCREW
    Misc
    Screw PHMS #10-32 X 1 Stainless Steel Slot Head Murrays Part# 19-2915 Stainless steel, pan head #10-32 x 1" machine screw with slot is used as dolphin striker screw on all Prindles. Replaces Murrays item #56-F112. Also used in some Hobie Applications, compare to 8030111 Hobie Part. Applications: H18/18 SX/16 and Getaway Tiller Hinge Screw: 2
    SCREW PHMS #10-32 X 1" (SS)
    Misc
    Washer 5/16 x 3/4 Flat SS Murrays Part# 50-8080671 EZ Loc Rudder Assembly Lower Bolt Washer for Hobie Bravo, Getaway and Wave Hobie Part# 8080671
    WASHER SS 5/16 x 3/4" FLAT
    Hobie