All Prindle 19 Parts

120 products

    120 products
    Shroud Stay Adjuster 7 Hole Murrays Part# 25-3310 Stainless steel shroud adjuster with seven 1/4" holes. ​Use #22-9802 clevis pin at top and #22-9808 at bottom. Fits: H14/16/18/20, Wave and Getaway. Compare to Hobie Part# 20830010
    SHROUD STAY ADJUSTER 7-HOLE
    Murrays Sports
    Prindle split rings and clevis pin kit, mast hinge pin
    PRINDLE PINS & RINGS KIT
    Murrays Sports
    Murrays Part# 001-0062 Replacement tiller yoke assembly for all hiking sticks sold by Murrays. Used to connect the tiller extension to the tiller crossbar. Includes two contoured spacers that provide a solid platform for the yoke to sit on. Compare to Hobie Cat® Tiller yoke assembly #3205 or NACRA connection part tiller/joystick #31072 Applications: All Hobies and Prindles Tiller Yoke Assembly: 1
    TILLER YOKE ASSEMBLY WITH SPACERS
    Murrays Sports
    Diamond Tang 3-Hole Bottom Murrays Part# 56-6813 The Prindle Diamond Tang 3-Hole (Bottom) is a 3-hole lower tang for diamond wire is for Prindle 18, 18-2 and 19. Performance Sailing factory item #6813; Nacra Sailing #31444.
    PRINDLE DIAMOND TANG 3-HOLE BOTTOM
    NACRA
    Nacra Crossbar Bolt Chip Murrays Part# 56-2510 The Nacra Crossbar Bolt Chip is for beam mounting on Prindles and Nacras. Nacra Sailing factory item# 30069 Prindle item# 2510
    NACRA CROSSBAR BOLT CHIP
    NACRA
    Spreader Tip Plate Murrays Part# 56-9842 Spreader tip plate for all Nacras and Prindle 18, 18.2 and 19. Nacra Sailing factory item# 30316
    NACRA SPREADER TIP PLATE
    NACRA
    DIAMOND WIRE ROLLER
    Misc
    Trap Shock Cord: Nacra, Prindle, Sol Cat and Getaway Murrays Part# 001-8019 A trapeze shock cord is an absolute necessity because it keeps the trapeze system in place and ready for hook-up. One hook connects to either the thimble on the trapeze wire or the adjustment line, then runs under the tramp and connects to the other side in the same location. A plastic carbine hook is installed on one end only; the other hook is included to be installed after the shock cord is put on the boat. Cord is 1/4" d
    NACRA/PRINDLE/SOL CAT AND GETAWAY TRAP SHOCK CORD
    Murrays Sports
    Quick Release Detent Pin 1/4 X 3" Murrays Part# 18-4D300 Economical quick release pin has a spring-loaded ball that exerts sufficient pressure to help avoid accidental release. Measurements are 1/4" diameter x 3" maximum grip length (distance from the shoulder to the locking ball bearings). Uses: - Use as mast step pin on Hobie® 21 and Prindle 16/18/18-2/19 cats. Compare to Hobie part # 8020501
    Quick Release Detent Pin 1/4 X 3" Murrays Part# 18-4D300 Economical quick release pin has a spring-loaded ball that exerts sufficient pressure to help avoid accidental release. Measurements are 1/4" diameter x 3" maximum grip length (distance from the shoulder to the locking ball bearings). Uses: - Use as mast step pin on Hobie® 21 and Prindle 16/18/18-2/19 cats. Compare to Hobie part # 8020501
    QUICK RELEASE DETENT PIN 1/4 X 3"
    Misc
    Vertical Pole Tang Murrays Part# 56-1045 The vertical pole tang is part of the Prindle 19MX Conversion Kit. Performance Sports factory item #1045 is limited to stock on hand.
    NACRA VERTICAL POLE TANG
    NACRA
    3-Hole Pad Kit Murrays Part# 001-0110 This base kit is for Harken®, Hobie® or Murray 360 cleats without swivel base adapters. Kit includes one 3-hole base, one swivel base adapter (#25-3001), plus three #10 FHSMS (#19-1626). Ronstan swivel 360 cleats include swivel base adapters, so this kit is not necessary. Fits Hobie® or Prindle elliptical crossbar.
    3-HOLE PAD KIT
    Murrays Sports
    Dolphin Striker Casting Murrays Part# 56-2009 Performance Sports factory dolphin striker casting for all Prindle Cats
    Prindle part numbers 2505, 2009 and 2009C
    PRINDLE DOLPHIN STRIKER CASTING
    NACRA
    Hobie Cat #80550005 Main sail batten pocket protector kit. Hobie, Nacra, Prindle.
    MAIN SAIL POCKET PROTECTOR KIT
    Murrays Sports
    PRINDLE MAST STEP HINGE PIN
    Murrays Sports
    PRINDLE 18.2/19 OWNERS MANUAL
    Murrays Sports
    NACRA and Prindle Rudder Spring Murrays Part# 56-4016 The NACRA and Prindle Rudder Spring is the rudder spring for all Prindle and most newer Nacras (Late Model US boats, Inters and all European NACRA boats) is Nacra Sailing factory item #30418. Fits Nacra 460, Nacra 500, Nacra 570, Nacra 16, Nacra 17, Nacra F18 Infusion, Nacra F20 Carbon and all Inters.
    ILLUSTRATED PRNDLE RUDDER PARTS LIST
    NACRA/PRINDLE RUDDER SPRING
    NACRA
    Rudder Lock Release Strap Murrays Part# 56-4010 This is one of two plates used in each rudder assembly on a Prindle beach cat. This is part of the internal assembly that moves up and down as part of the rudder pull up/down system. The Prindle Rudder Lock Release Strap is works on all Prindles. Nacra sailing factory item# 30415 Prindle Part# 4010
    PRINDLE RUDDER LOCK RELEASE STRAP
    NACRA
    Brindle Pole Tang P19MX Murrays Part# 56-1043 The bridle pole tang is part of the Prindle 19MX Conversion Kit. Performance Sports factory item #1043 is limited to stock on hand.
    PRINDLE BRIDLE POLE TANG
    NACRA
    Prindle Centerboard Lock Bearing P18.2 19 Murrays Part# 56-4870 Centerboard lock bearing for Prindle 18.2 & 19 is Nacra Sailing factory item #30429. Approximately 1" diameter x 5/16" high.
    PRINDLE CENTERBOARD LOCK BEARING
    NACRA
    Jib Track End Stop Murrays Part# 56-1911 1 Jib track end stop. Fits Nacra 5.5SL, 5.7, 5.8, 6.0, as well as Prindle 18-2 and 19.
    PRINDLE/NACRA JIB TRACK END STOP
    NACRA
    Prindle 18/19 Ronstan Mast Head Base Sheave Murrays Part# 56-6804 Replacement sheave for mast base on Prindle 15, 18, 18.2, 19 and Nacra 2003 and later mast head. Sheave measures 1-1/8" diameter x 3/8" wide. Please note that this item replaces #6803 that is no longer available.
    PRINDLE 18/19 RONSTAN MAST HEAD SHEAVE
    Ronstan
    Replacement Sheave Prindle Rudder Upper Ronstan PN RF1741 Replacement sheave for upper part of rudder casting on all models of Prindle catamarans. Replacement for Performance Sports item #4009. 1/4" wide x 3/4" diameter, 1/4" hole.
    ILLUSTRATED PRNDLE RUDDER PARTS LIST
    RONSTAN 19MM ACETAL SHEAVE, 6MM WIDTH
    Ronstan
    Centerboard Spring Kit Prindle Factory centerboard spring kit for Prindle 18.2 and 19 includes 4 springs. Performance Sports factory item #1027.
    PRINDLE CENTERBOARD SPRING KIT
    NACRA
    Bolt Hex Head 5/16-18 X 4.50" (Stainless Steel) Murrays Part# 19-2237 Stainless steel hex head bolt for Prindle mast rotation control arm. Use #19-2520 nylock nut. This bolt is a replacement for item #56-F110 Comparable to Hobie Part# 8040211
    BOLT HEX HEAD 5/16-18 X 4.50" SS
    Misc
    Clevis Pin 1/4 X 3/4" Murrays Part# 56-4012 The Clevis Pin 1/4 X 3/4" is used on Prindle rudders, Nacra mast head sheave and as Nacra/Prindle shroud pin. Prindle Part# 4012
    CLEVIS PIN 1/4 X 3/4"
    NACRA
    Out of Stock
    Upper Rudder Roller Murrays Part# 56-4009 This plastic spacer/ roller is used in the locking mechanism of Prindle Rudder systems. It is also used as a boom roller.
    PRINDLE UPPER RUDDER ROLLER
    NACRA
    Batten Cap Leech Adjustable H16 Jib Each Murrays Part# 012-3004-1 No more knots at the trailing edge. Adjust Hobie® 16 jib sail shape in seconds without tying and untying knots. Release tension to prolong sail shape and life. Individual cap. Sold Individually
    ADJUSTABLE LEECH JIB BATTEN CAP (EA)
    Tren-Tec
    Gooseneck Bolt Murrays Part# 56-F131 3/8" x 1-1/2" gooseneck bolt for Nacra 5.2 and all Prindles. Performance Sports factory item # F131
    PRINDLE/NACRA GOOSENECK BOLT
    NACRA
    Stainless steel clevis pin. Measurement is 1/4" diameter x 5/8" grip length. Hobie part number 8020361, 8020381 and 8020380.
    1/4 X 5/8" Clevis Pin Murrays Part# 22-9802 Stainless steel clevis pin. Measurement is 1/4" diameter x 5/8" grip length (shoulder to the split ring hole).  Uses: Most commonly used to connect shrouds and forestays to 7 or 10 hole shroud adjusters on Hobie, Nacra and Prindle catamarans. Hobie 18 gooseneck vertex pin Hobie 18 outhaul car sheave pin Hobie Part# 8020361, 8020381 and 8020380
    CLEVIS PIN 1/4 X 5/8"
    Misc
    Leech Cap Adjustable Main Prindle Murrays Part# 012-6003-1 No more knots at the trailing edge. These Perfect Pocket leech batten caps adjust sail shape in seconds without tying and untying knots. Release tension to prolong sail shape and life.Tren Tec adjustable batten caps for Prindle catamaran mainsails. Leech caps are used on the trailing edge of the sail. Sold individually
    PRINDLE 16 MAIN ADJUSTABLE LEECH CAP
    Tren-Tec
    Prindle Rudder Lock Bolt Nut Murrays Part# 56-4018 The Prindle Rudder Lock Bolt Nut is the factory replacement 3/8″ hex nut for rudder lock bolts on all Prindles. Also used as the jam nut for adjuster screw on Nacra bridle foil assembly. Nacra Sailing factory item #30420. Prindle part number 4018
    Prindle rudder parts 4000, 4001, 4002, 4004, 4005, 006, 4007, 4009, 4012, 4010, 4014, 013, 4016, F115, F120
    PRINDLE/NACRA RUDDER LOCK BOLT NUT
    NACRA
    3/16 - 1/4" Split Ring with Pigtail Murrays Part# 22-9491 A pigtail makes this split ring (ring ding) easier to open than standard split rings. For use on 3/16″ – 1/4″ clevis pins Material: 316 Stainless steel. Medium Split ring Dimensions: 5/8″ Diameter This is the most common size Split ring on Hobie, Nacra and Prindle Catamarans. Applications: All Hobies Shroud and Forestay split ring H18/ Hobie 18 SX – Tiller Yoke Clevis Pin Ring Also called Ring Ding, Clevis Ring, Cotter Ring or Ringy Ding
    3/16 - 1/4" SPLIT RING WITH PIGTAIL
    Misc
    Murrays PN 001-0053 The Murrays Rudder Stiffening Spacer is a 2" diameter spacer for use on Hobie, Nacra and Prindle catamarans to eliminate excessive clearances between rudders and castings which cause rudder slop, side to side wobble, and thwart rudder alignment. A kit with spacers and nuts is also available (#01-2053).  The Murrays Rudder Stiffening Spacer are quite thin so that you can achieve a perfect fit. Standard kits come with 8 spacers.
    RUDDER STIFFENING SPACER
    Murrays Sports
    NACRA/PRINDLE BOLT FOR GUDGEON 1/4-20X1.25"
    NACRA
    Prindle Rudder Lower Plastic Spacer Murrays Part# 56-4014 Prindle Rudder Lower Plastic Spacer is used on the rudder systems of all Prindle models. Performance Sports factory item #4014. 9/16″ wide x 1/2″ diameter, 1/4″ hole.
    ILLUSTRATED PRNDLE RUDDER PARTS LIST
    PRINDLE LOWER RUDDER PLASTIC SPACER
    NACRA
    Nylon Washer Internal Casting Prindle Murrays Part# 56-F118 Nylon washer is used on Prindle rudder casting to separate the upper sheaves to help keep the line from fouling. Order four per side to remove as much slop as possible. Performance Sports factory item #F118
    PRINDLE NYLON WASHER INTERNAL CASTING
    NACRA
    Used for tiller connection on Hobie Cats®. The stainless 1/4-20 stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Equivalent to Hobie #8050111. Also Equivalent to Nacra/Prindle F123 gudgon nut for all Prindle and older Nacras. Applications: Hobie 18 / H18: Bow Tang Nut Qty: 6 Rudder Adjustment: 1 Hobie Getaway: Forestay Yoke Nut
    NYLOCK NUT 1/4-20 SS
    Misc
    WASHER #8 (WH NYLON) Murrays PN 19-4006WH White nylon washer is used for installation of access ports (hatches).
    WASHER #8 WHITE NYLON
    Misc
    Nylon Spacer Murrays Part# 56-4011 Prindle rudder spacer, Prindle part number 4011.
    ILLUSTRATED PRNDLE RUDDER PARTS LIST
    PRINDLE RUDDER SPACER
    Murrays Sports
    Cotter Pin 3/32 X 3/4 Murrays Part# 19-1015 Cotter pins are used on all Hobie, Nacra and Prindle rudder pins. They are used to secure the rudder pins. Compare to Hobie Cat® #8060111. Stainless steel cotter pin measures 3/32" x 3/4".
    COTTER PIN 3/32 X 3/4" SS
    Misc
    Recently viewed