All Bravo Parts

66 products

    66 products
    Hobie rudder bushing. Hobie part number 8062001
    RUDDER TITE BUSHING EACH
    Murrays Sports
    Out of Stock
    Hobie Bravo Batten Cap Murrays Part# 50-9101100 Hobie batten cap for round battens Sold individually
    BRAVO BATTEN CAP
    Hobie
    Universal Drain Plug for most Hobie, Nacra and Prindle Catamarans which includes a gasket and fits most Hobie, Nacra and Prindle catamarans. Hobie part number 10091000
    Hobie drain plug 10091000 Hobie 18
    HOBIE DRAIN PLUG WITH GASKET
    Misc
    Screw 12x24x1 Pan Head (Long Lock) Murrays Part# 50-8030402 This screw is used to hold the rudder gudgeons on the back of the boat.  Hobie Part# 8030402
    SCREW 12x24x1 PAN HEAD (LONG LOCK)
    Hobie
    Bolt 5/16-18 x 2-1/2" HX HD Murrays Part# 50-8040321 EZ Loc Lower Rudder Bolt for Hobie Bravo, Getaway and Wave. Hobie Part# 8040321
    BOLT 5/16-18 x 2-1/2" HX HD
    Hobie
    Hobie Tiller End Cap Murrays Part# 50-10560000 Replacement end cap for Hobie tillers.
    HOBIE TILLER END CAP
    Hobie
    Out of Stock
    Bolt 5/16-18 x 2-3/4" HX HD Murrays Part# 50-8040391 EZ Loc upper rudder bolt for Hobie Bravo, Getaway and Wave  Hobie Part# 8040391
    BOLT 5/16-18 x 2-3/4" HX HD
    Hobie
    Out of Stock
    Bolt 5/16-18 X 2" Murrays Part# 50-8040331 Replacement 5/16-18 x 2" bolt is used as a rudder bolt on Hobie® Pre-EZ Lock Rudder System. Hobie Part# 8040331
    BOLT 5/16-18 X 2"
    Misc
    Hobie rivet casings sleeves seal rivets to prevent water penetration. When used with a rivet they seal the hole to prevent water from getting through the center of the rivet. Rivet Casings are recommended for use on all rivets on the mast to keep the mast water tight. Compatible with all 3/16 diameter rivets up to 5/8" long. Compatible with all rivets on Hobie, Nacra and Prindle catamarans except traveler tracks. Requires 13/64" hole. Hobie part number 8011291, 8011290, also called rivet cap.
    RIVET CASING 6-10(3/16 X 5/8)
    Hobie
    Screw 1/4/20x1.25" PHPMS Murrays Part# 50-8032061 Rear Hatch Screw for Hobie Bravo. Hobie Part# 8032061
    SCREW 1/4/20x1.25" PHPMS
    Hobie
    Screw 1/4-20 x 1" THMS-P SS Murrays Part# 50-8030701 Hobie® factory replacement 1/4-20 x 1" stainless steel screw. Used on Hobie® pre-EZ-Loc rudder system, tendon tiller connector, rudder adjuster, Hobie 20 shroud anchor plate. Applications: H18/ Hobie 18 SX Rudder Adjuster Screw: 1 Compare to Hobie Part# 8030701
    SCREW STAINLESS STEEL 1/4-20x1"
    Hobie
    Nut Nylock 5/16-18 Low Profile Murrays Part# 50-8050331 Hobie® factory replacement low-profile 5/16-18 nylock nut.  Fits EZ Loc Upper and Lower Rudder Housing Hobie Bravo, Getaway and Wave. Hobie Part# 8050331
    NUT NYLOCK 5/16"-18 LOW PRO
    Hobie
    Out of Stock
    Screw 1/4-20 x 1-1/4" PHMS Murrays Part# 50-8031191 Tiller Extension Hinge Screw
    SCREW 1/4-20 x 1-1/4" PHMS
    Misc
    Screw RHMS 1/4-20 X 1" Murrays Part# 50-8030211 Hobie® factory replacement round head machine screw measures 1/4-20 x 1". Measurements are diameter and threads per inch times grip length. Applications: Hobie 18 - Shroud anchor plate screw
    SCREW RHMS 1/4-20 X 1"
    Hobie
    3/16 - 1/4" Split Ring with Pigtail Murrays Part# 22-9491 A pigtail makes this split ring (ring ding) easier to open than standard split rings. For use on 3/16″ – 1/4″ clevis pins Material: 316 Stainless steel. Medium Split ring Dimensions: 5/8″ Diameter This is the most common size Split ring on Hobie, Nacra and Prindle Catamarans. Applications: All Hobies Shroud and Forestay split ring H18/ Hobie 18 SX – Tiller Yoke Clevis Pin Ring Also called Ring Ding, Clevis Ring, Cotter Ring or Ringy Ding
    3/16 - 1/4" SPLIT RING WITH PIGTAIL
    Misc
    Nut Nylock 5/16-18 Stainless Steel Murrays Part# 19-2520 5/16-18 nylock nut is used on Hobie® rudders. The stainless steel hex nut with nylock insert will not rust or work loose if properly installed. Compare to Hobie Cat® item #8050311 and 8050321 shroud anchor pin nut Used with Hobie Getaway Bow Tang Bolt
    NUT NYLOCK 5/16-18 (SS)
    Misc
    Screw RHMS 1/4-20 X 1/2" Stainless Steel Murrays Part# 19-3019 Stainless steel, Phillips pan head 1/4-20 x 1/2" machine screw is used to fasten mast bearing on post-1990 Hobie® 18. Compare to Hobie 8032011
    SCREW RHMS 1/4-20 X 1/2" (SS)
    Misc
    SCREW STAINLESS STEEL #10 x 3/4 PHSM-PH
    Hobie
    Screw #10 x 1-1/4 PHSMS-P Murrays Part# 50-8030261 Tiller Hinge Screw for Hobie Fiberglass Tiller.
    SCREW #10 x 1-1/4 PHSMS-P
    Hobie
    Screw #10 x 1/2 PHSMS-P Murrays Part# 50-8031151 Hobie Part# 8031151
    SCREW #10X1/2" PHSMS-P
    Hobie
    Nut Nylock Lo-Pro 1/4-20 Murrays Part# 50-8050101 Hobie® factory replacement low profile 1/4-20 nylock nut. Used on Hobie 14 and 16 gooseneck assembly. Hobie Part# 8050101
    NUT NYLOCK LOW PROFILE 1/4-20"
    Hobie
    FIBER TENDON SCREW
    Misc
    Out of Stock
    Screw 10-32 x 3/4 PHPMS Murrays Part# 50-8030981 Mainsheet Bracket Screw for Hobie Bravo.
    SCREW 10-32 x 3/4" PHPMS
    Misc
    Nut 10-32 Nylock Low Profile Murrays Part# 50-8050211 Hobie factory low-profile Nylock 10-32 nut as used on EZ-Loc rudder assembly. Hobie Part# 8050211
    NUT 10-32 NYLOCK LOW PROFILE
    Hobie
    Washer 5/16 x 3/4 Flat SS Murrays Part# 50-8080671 EZ Loc Rudder Assembly Lower Bolt Washer for Hobie Bravo, Getaway and Wave Hobie Part# 8080671
    WASHER STAINLESS STEEL 5/16 x 3/4" FLAT
    Hobie
    WASHER STAINLESS STEEL 1/4 x 1/2 x .032"
    Hobie
    Recently viewed